UVISION X1 LCD Multimedia Projector User Manual

: June 6, 2024
: Uvision

UVISION X1 LCD Multimedia Projector User Manual

Safety Instructions

Read all warnings and follow all instructions.
Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from over heating, it is recommended to install the projector in a location that does not block ventilation. As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the projector in an enclosure such as a book case or a cabinet that restricts air flow.
Avoid exposing the projector to direct sunlight or other sources of sustained heat. Do not install near any heat sources such as radiators, heat registers, stoves, or othe r devices.
Do not use the projector near water or moisture. To reduce the risk of fire and/or electric shock, do not expose the projector to rain or moisture.
Do not place the projector on an uneven or unstable surface. The projector may fall over, causing personal injury or projector malfunction.
Do not look straight at the projector lens during operation. The intense light beam may damage your eyes.
Please remove the lens cap when the projector is operating . Do not block the projection lens with any objects as this could cause objects to become heated and deformed or even cause a fire.
Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short out parts that could result in fire or electric shock.
When moving the projector, be careful not to drop or bump the projector on anything.
Do not place any heavy objects on the projector or connection cables.
Do not stand the projector on end vertically. Doing so may c ause the projector to fall over, causing personal injury or projector malfunction.
Only use attachments/accessories specified by the manufacturer.
Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If th e projector does become wet, disconnect it from the power supply and contact UVISION to have projector serviced.
When the projector is under operation, you may sense some heated air and odor from its ventilation grill. It is a normal operation and not a de fect.
If smoke, an abnormal noise, or a strange odor is present, immediately switch the projector off and contact UVISION. It is dangerous to continue using the projector.
Disconnect the power cord from the AC outlet if the projector is not being used for a long period of time.
Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please contact UVISION before you send the unit for repair.

Trademarks
UVISION and the UVISION logo are
trademarks of UVision Innovation Co., Ltd , registered in the United States and other countries.
Regulatory Notices
FCC Compliance Statement

This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions

This device may not cause harmful interference, and
This device must accept any interference received including interference that may cause undesired operation.

Introduction

Package Contents

Your projector comes with all the items shown below. Ensure that you have all the items, and contact UVISION if anything is missing.

UVISION X1 Projector Remote Control Power Cord

HDMI Cable User Manual

Note: The Remote Control not includes battery.

Product Overview

UVISION X1 Projector Controls and Functions

Item	Description
1	IR Receiver for Remote Control
2	Front tilt adjustment stand
3	Focus adjust

Item	Description
4	Dual Channel Stereo Out
5	Heat dissipation air inlet

Item	Description
14	Power Button

Connection Ports

Item	Description
6	Dual Channel Stereo Out
7	IR Receiver for Remote Control
8	USB Port
9	AV Port
10	AC Power Cord inlet
11	HDMI Port
12	USB Port
13	AUX Port

Remote Control

Using the UVISION X1
Turning On
Off the Projector
Turning Your Projector On

Connect the power cord and appropriate signal cables to the projector.
Remove the lens cap.
Press the Power button or the Power key by remote control.
Turn on your source (computer, DVD player, etc).
Connect your source to the projector using the appropriate cable.
The input source is determined by the last connected input source. (By default, the input source of the projector is set to Multimedia). Change the input source of the projector if necessary.

Note: Turn on the projector before you turn on the source (computer, DVD player, etc.). The Power button light red until pressed. After turn on the projector, button light blue.

Turning Your Projector Off

Press the Power button or the Power key by remote control. Follow the instruction displayed on screen to properly turn off the projector.
Press the Power button or the Power key again.
Disconnect the power cord from the electrical outlet and the projector.

Note: The “Power key to standby any key to cancel” message will appear on the screen. The message disappears after you can press the any key to clear it.

Adjusting the Projection Image

Raising the Projector Height

Raise the projector to the desired display angle, and use the front tilt adjustment wheel to fine tune the display angle.

Lowering the Projector Height

Lower the projector, and use the front tilt adjustment wheel to fine tune the display angle.

Adjusting Projection Image

Focus Rotate the Focus Ring to sharpen the Image Focus until the blurred image becomes clear.

Adjusting Projection Image Size

Place UVISION X1 on a flat, stable foundation squarely in front of the projection surface.
For best results, the projection surface shall be white and flat. The distance between this
projector and the projection surface must be a minimum of 1 .1 meter (3 5 inches) and a max imum of 5.9 meters ( 200 inches).
The distance between this projector and the projection surface determines the approximate size of the image. Use the table below to determine approximately how far to place this projector from the screen based on the size o f the projected image.

Screen size	Projection distance (m)
35 inches	1.1m
60 inches	1.8m
80 inches	2.4m
100 inches	3.0m
150 inches	4.4m
200 inches	5.9m

Adjusting Projection Image Keystone

The projector supports horizontal and vertical keystone correction within a degree of ±40. You can correct the horizontal or vertical keystone distortion manually until the shape is evenly rectangular.

Horizontal Correction

Signal Source choosing

Press key choose corresponding input source to connect. If there is no corresponding signal channel selection will show no signal. Step are as following:

Connection to HDMI Playback Devices

This projector can be connected to various HDMI playback devices such as a TV box, TV stick, DVD player, set top box (STB), gaming console or other devices.

Connection to a AV Device

This projector can be connected to various AV playback devices such as a DVD player, gaming console or other devices.

Connection to External Audio Devices

This projector can also be connected to external devices, including headphones and speakers.
When connected to external speakers, the built in speaker system is disabled.

Connection to External Audio Devices

This projector can also be connected to external devices, including headphones and speakers. When connected to external speakers, the built-in speaker system is disabled.

Use Screen Mirroring

Android:	Miracast Dongle is required. (not included)
iPhone:	Lightning to HDMI cable is required. (not included)

**PICTURE**

SOUND

Item	Description
Sound Mode	Standard / MUSIC / MOVIE / Sports / User
Surround Sound	Off / SRS TruSurround XT / Surround

TIME

Item	Description
Clock	Clock Time Setting

Off Time

| Off / Once / Every Day

Mon ~ Fri. / Sat ~ Sun. / Sunday

On Time

| Off / Once / Every Day

Mon ~ Fri. / Sat ~ Sun. / Sunday

Sleep Timer| Off / 10min / 20min / 30min / 60min / 90min
Auto Sleep| Never / 4Hours / 6Hours / 8Hours

OPTION

Item	Description
OSD Language	Select an on-screen language.

Keystone

| Horizontal : -25 ~ 25

Vertical : -25 ~ 25

Rotate

| Rear / Front

Front Ceiling / Rear Ceiling

Software Update (USB)

| Press insert a USB to upgrade the

firmware version.

Restore Factory Default| Yes / No
Version| 20200910 V2.1.0.4

Appendices

Troubleshooting

If you experience problems with your projector, see the following troubleshooting tips. If the problems persists, please contact UVISION.

Problem	Possible Solution

__

The remote control doesn’t work?

| • Make sure the battery is already installed in the remote control.

• Replace the batteries.

• Make sure remote points at IR Receiver directly.

• Do not cover IR Receiver.

__

Blurred image?

| • Adjust focus ring and keystone.

• Projection and screen/wall must be in effective distance.

Reversed projection image?| • Rotate to flip the projection image.
__

My USB disk or hard drive can not read?

| • Make sure the fotmat of you USB disk or hard drive is FAT32 or NTFS.
What Should I do if I want to watch the

content from Hulu, Netflix, and similar services via the projector?

| • Please prepare a Fire TV Stick, Roku Stick or Chromecast, than connect it to

the projector to watch the content.

Product Specification

Item	Specifications
Display technology	LCD
Light source	LED
LED life	30000 hours
Optical engine	Full Sealed & Dustproof Design
Resolution	1920x1080P
Brightness	200 ANSI / 3600 lumens
Contrast ratio	5000 : 1
Throw ratio	1.33 : 1
Throw distance	1.1m to 5.9m
Projection image size	35 – 200 inch
Projection focus	Manual focus
Projection Keystone	±40 Horizontal and Vertical