NORTEK GoControl GD00Z-8-GC Installation Guide
- June 6, 2024
- NORTEK
Table of Contents
GD00Z-8-GC
GARAGE DOOR OPENER REMOTE COMMAND TRANSCEIVER with TILT SENSOR
Installation Instructions
PRODUCT DESCRIPTION
GD00Z-8-GC Overview
- A garage door opener remote command transceiver with built-in Z-Wave
- Allows remote operation of a garage door opener using Z-Wave controllers.
- Acts as a Z-Wave repeater to improve communications within the Z-Wave mesh
GD00Z-8-GC Summary of Operation
- GD00Z-8-GC connects to the garage door opener’s pushbutton wall console
- A wireless tilt sensor mounts on the garage door and reports the door’s position to GDOOZ-8-GC.
- GDOOZ-8-GC responds to Z-Wave commands from Z-Wave controllers to open or close the garage door.
- A warning indicator light flashes and a beeper sounds for 5 seconds before the door begins to move.
- If the door does not completely open or close, a second open or close command can be sent after 30 seconds.
- If the door does not completely open or close after the second attempt, the GD00Z-8-GC operation is suspended until a local garage door pushbutton is activated.
Z-Wave Information
- Z-Wave(us is a registered trademark of Sigma Designs Inc. and/or its subsidiaries.
- Z-Wave is an Interoperable two-way RF mesh networking technology designed (or used with a Z-Wave gateway/controller and other Z-Wave enabled devices.
- Replication is the process of copying or transferring your Z-Wave network from one controller to another.
- This is a Security Enabled Z-Wave product and must be used with a Security enabled Z-Wave controller in order to fully utilize this product. As such, this device will not respond to Basic CC commands.
- ASSOCIATION: GDOOZ-8-GC supports 1 Group with 1 Node. Group 1 must be assigned the Node ID of the controller to which unsolicited notifications from the GDOOZ-8-GC will be sent. The Z-Wave controller should set this association automatically after inclusion.
S2 Security
- New S2 security uses Elliptic Curve Diffie Hellman key exchange protocol to establish a secure communication channel.
- Uses multiple “Keys” to create a permanent Key.
- Virtually impossible to hack.
- Z-Wave hub must also support S2 Security. If the hub does not support S2, the device will operate using standard security.
**** SAFETY NOTES
WARNING
This operating system is equipped with an unattended operation feature. This door could move unexpectedly. NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING
This system can be installed on sectional type (roll-up) doors only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING
The Remote Command Transceiver must be mounted in the garage, in sight of the garage door, where the visual and audible movement warning indicators can be clearly seen and heard.
WARNING
Do not install the Remote Command Transceiver on garage door operators manufactured prior to 1993 (models without an operational safety beam entrapment detection system).
PRODUCT COMPONENTS
TILT SENSOR INSTALLATION AND BATTERY
PAIRING (INCLUDING) WITH THE SYSTEM
FO INCLUDE THE GDOOZ-8-GC INTO YOUR CONTROLLER
-
Place your Z-Wave Controller into
Discovery or Include mode. -
Press and release the link button on the GDOOZ-11-GC
-
Confimi that the GDOOZ-8-GC was recognized by your Z-Wave Controller.
Refer to your Z-Wave Controllers instructions for additional information on including devices.
TO EXCLUDE THE 6000Z-8-GC FROM YOUR CONTROLLER
- Place your Z-Wave Controller into Exclude mode.
- Press and release the link button on the GDOOZ-R-GC
- Confirm that the GDOOZ-8-GC was excluded by your Z-Wave Controller.
Refer to your Z-Wave Controllers instructions for additional information on excluding devices.
GD00Z-8-GC MOUNTING
GD00Z-8-GC CONNECTIONS
SYSTEM OPERATION
- Restore power to your Garage door opener.
- To synchronize the system, use the garage door opener’s push-button to manually open and close the door.
- Use the ADT pulse touch-screen or mobile app to control your garage door, view status, and add your garage door control to automation and modes. (For example, you can schedule your garage door to close nightly at sunset.)
- The GDOOZ-8-GC will beep and flash for five seconds before the door moves.
- The GDOOZ-8-GC will activate the door opener and open or close the door.
- The touchscreen or mobile app will show the new status of the door after the door completes its cycle.
OPERATION NOTES
- The warning light will flash and the warning beeper will sound for five seconds before the door opener is activated. STAY CLEAR OF THE DOOR AND DOO R THEY ARE ABOUT TO MOVE!
- If the door does not completely open or close after remote activation, the G000Z-8-GC will allow the user to try to operate the door one more time. If the second attempt fails, the GDOOZ-8-GC will go into lock-out mode. See Note #3.
- If the GDOOZ-8-GC is in lock-out mode and will not accept remote commands activate the door from the pushbutton wall console.
- Once the GDOOZ-8-GC has initiated the movement of the garage door, another r command cannot be sent for 30 seconds. This eliminates the chance f “bouncing” the garage door and possibly damaging the garage door opener.
GDOOZ-8-GC Specifications
Power Supply: Input: 120 VAC, 0.35 A Output: 12 VDC, 1 A
Operating Temperature: -4°-122° F (-200-50° C)
Audible Alarm: 45 db @ 10 feet
Strobe: 360 Lumens
Communications: Z-Wave (908.4 MHz)
Mounting: Screws and anchors to
the ceiling, or bracket to the
opener’s hanging hardware
Tilt Sensor Specifications
Power Supply: Type CR2032 Coin Cell Battery
Operating Temperature: 4°-122° F (-20°-50° C)
Battery Life: 24 Months (typical)
Communications: Proprietary 345 MHz
Range: 100 ft. line-of-sight to GD00Z-8-GC
Mounting to Garage Door Double-sided tape or two mounting screws (Specifications subject to change without notice)
NOTICE TO USERS IN CALIFORNIA – CR COIN CELL LITHIUM BATTERY INFORMATION:
THIS PRODUCT ,;1* CONTAINS A CR COIN CELL LITHIUM BATTER Y WHICH CONTAINS
PERCHLORATE MATERIAL SPECIAL HANDLING MAY APPLY – SEE
www.dtsc.ca.gov/hazardouswaste/porchlorite
KEEP AWAY FROM SMALL CHILDREN. IF BATTE IS SWALLOWED, PROMPTLY SEE A DOCTOR. NOT TRY TO RECHARGE THIS BATTERY. DISP05, OF USED BATTERIES, MUST BE MADE IN ACCORDANCE WITH THE WASTE RECOVERY AI RECYCLING REGULATIONS IN YOUR AREA.
TROUBLESHOOTING
PROBLEM| POSSIBLE CAUSE| CORRECTIVE ACTION
---|---|---
Unable to include in Z-Wave network.
| GDOOZ-8-GC was not properly excluded Tram from a previous Z-Wave network.
| 1. Reset the GDOOZ-8-GC by pressing the LINK button 5 times. A quick beep followed by a longer beep will indicate the reset. Reset should only be used in the case of a missing or inoperative primary controller.
The GDOOZ-8-GC flashes and beeps when activated but the door does not move.
| Obstruction blocking the door or incorrect Wring.| 2 Make sure that there are no obstacles preventing the door from moving. 3 Make sure that the GDOOZ-8-GC connection wires are connected to the proper terminals on the garage door opener. Trace the wires from the garage door opener’s pushbutton wall console to the door opener. This is where the GDOOZ-8-GC connection wires should be connected.
The GDOOZ-8-GC flashes and beeps when activated but the door does not move.
| The till sensor signal is not being received by the GDOOZ-8-GC.
| 1. Pair the till sensor with the GDOOZ Garage Door Controller. a. Press and hold the pair button on the side of the GD00Z-8-GC main unit for about 7 seconds. It will emit a short chirp. b. Release the button. c. Rotate the tilt sensor 90 degrees to trigger a transmission. A short chirp should be heard. d. If a short chirp is not heard, rotate the tilt sensor again. 2. Make sure the tilt sensor is mounted correctly on the garage door, with the arrow pointing up. 3. Make sure the battery pull tab has been removed from the tilt sensor. 4. Replace the battery in the tilt sensor.
NORTEK SECURITY & CONTROL LIMITED WARRANTY
This Nortek Security & Control product is warranted against defects in material and workmanship for twelve (12) months. This warranty extends only to wholesale customers who buy direct from Nortek Security & Control or through Nortek Security & Control’s normal distribution channels. Nortek Security & Control does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty if any. There are no obligations or liabilities on the part of Nortek Security & Control LLC for **consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All Implied warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until the warranty expires. This Nortek Security & Control LLC Warranty is In lieu of **all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization Number (RPM). Contact Nortek Security & Control Returns at 1-855-546-3351 for an RPA# and other important details.
REGULATORY NOTICES
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
Les changements ou modifications non approuves expressement par la parte responsable de la conformith pourrait annuler l’autorite de l’utilisateur a faire fonctionner requipement.
This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide re, assemble protection against harmful Interference In a residential Installation, This equipment generates and can radiate radio frequency energy and, If not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver Is connected
- Consult the dealer or an experienced radio/TV technician for help
This Class B digital apparatus complies with Canadian ICES-003.
Cot appareil numerique de la classe B est conforme a la normeMMB-003 du Canada.
Copyright 0 2019 Nortek Security & Control LLC
10025383A
SECURITY & CONTROL
USA & Canada (800) 421- 1587& 800 392-0123
760-438-7000- Toll Free FAX (800)
68-1340
www.nortek.control.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>