SILICON LABS UG301 Si5332-12EX-EVB Low Hitter Clock Generator User Guide
- June 6, 2024
- SILICON LABS
Table of Contents
UG301: Si5332-12EX-EVB User’s Guide
The Si5332-12EX-EVB is used for evaluating the Si5332 Low Jitter Any-Frequency
Clock Generator. The Si5332 uses the patented Multisynth technology to
generate up to twelve independent clock frequencies each with 0 ppm synthesis
error. The Si5332-12EX-EVB has three independent ™input clocks. The Si5332
-12EX-EVB can be controlled and configured using the Clock Builder Pro ™(CB
Pro
) software tool.
EVB FEATURES
- Powered from the USB port or external power supply.
- Onboard 25 MHz XTAL allows the free-run mode of operation on the Si5332 or up to 2 input clocks for synchronous clocking.
- CBPro ™GUI programmable VDD supply allows devices to operate from 3.3, 2.5, or 1.8 V.
- CBPro GUI programmable VDDO supplies allow each of the 10 outputs to have its own power supply voltage selectable from 3.3, 2.5, or 1.8 V.
- CBPro GUI-controlled voltage, current, and power measurements of VDD and all VDDO supplies.
- SMA connectors for input and output clocks.
Functional Block Diagram
Below is a functional block diagram of the Si5332-12EX-EVB. This EVB can be
connected to a PC via the main USB connector for
programming, control, and monitoring. See section “2. Quickstart” or section
“7. Installing CBPro Desktop Software” for more information.
Si5332 CBPro™
The Si5332 is intended to be part of the CBPro software and this initial software release “showcases” that trait. This software contains:
- An EVB GUI that communicates and controls the EVB by allowing the user to set VDD supplies
- The ability to modify frequency plan (from the starting point CBPro file provided with this limited release) from an existing CBPro
file.
Si5332-12EX-EVB Schematics
The schematic and layout files are provided in here: schematics and layouts.
Please review the files, especially the DUT page in order to get familiar with
using the EVB through CBPro™
Si5332 CBPro.™
EVB GUI
The EVB GUI can be used to communicate the part for register access:
The first page shows the board’s identity.
The other pages for register access, VDD control, and GPIO control.
Installing ClockBuilderPro (CBPro) Desktop Software
To install the CBOPro software on any Windows 7 (or above) PC:
Go to https://www.silabs.com/products/development-tools/software
/clockbuilder-pro-software and download ClockBuilderPro
software.
Both installation instructions and the User’s Guide for ClockBuilderPro can be
found at this link. Please follow the instructions as indicated.
ClockBuilder Pro
One-click access to Timing tools, documentation, software, source code
libraries & more. Available for Windows and iOS (CBGo only).
www.silabs.com/CBPro
Timing Portfolio
www.silabs.com/timing| SW/HW
www.silabs.com/CBPro| Quality
www.silabs.com/quality| Support and
Community
community.silabs.com
---|---|---|---
Disclaimer
Silicon Labs intends to provide customers with the latest, accurate, and in-
depth documentation of all peripherals and modules available for system and
software implementers using or intending to use the Silicon Labs products.
Characterization data, available modules and peripherals, memory sizes, and
memory addresses refer to each specific device, and “Typical” parameters
provided can and do vary in different applications. Application examples
described herein are for illustrative purposes only. Silicon Labs reserves the
right to make changes without further notice and limitation to product
information, specifications, and descriptions herein, and does not give
warranties as to the accuracy or completeness of the included information.
Silicon Labs shall have no liability for the consequences of use of the
information supplied herein. This document does not imply or express copyright
licenses granted hereunder to design or fabricate any integrated circuits. The
products are not designed or authorized to be used within any Life Support
System without the specific written consent of Silicon Labs. A “Life Support
System” is any product or system intended to support or sustain life and/or
health, which, if it fails, can be reasonably expected to result in
significant personal injury or death. Silicon Labs products are not designed
or authorized for military applications. Silicon Labs products shall under no
circumstances be used in weapons of mass destruction including (but not
limited to) nuclear, biological or chemical weapons, or missiles capable of
delivering such weapons.
Trademark Information
Silicon Laboratories Inc.®, Silicon Laboratories®, Silicon Labs®, SiLabs®, and
the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®,
DSPLL®, EFM®, EFM32®, EFR, Ember®, Energy Micro, Energy Micro logo and
combinations thereof, “the world’s most energy friendly microcontrollers”,
Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®, ISOmodem®, Micrium,
Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis
Logo®, USBXpress®, Zentri, and others are trademarks or registered trademarks
of Silicon Labs. ARM, CORTEX, Cortex-M3, and thumbs are trademarks or
registered trademarks of ARM Holdings. Keil is a registered trademark of ARM
Limited. All other products or brand names mentioned herein are trademarks of
their respective holders.
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>