hama 00186412 Action Weather Station Instruction Manual

00186412
Weather Station
“Action”
Wetterstation
Operating Instructions

|
---|---

Controls and Displays
A Base station

1. Display
2. Outdoor temperature
3. Outdoor humidity
4. Time
5. Day
6. Month
7. Room humidity
8. Indoor temperature
9. Weather forecast symbol
10. ‘CH ’button =switches channel |increases the current set value| 11. ‘C/F |SET’ button =switches between °C and °F |sets time and date
12. ‘MEM ’button =displays the stored maximum/minimum indoor and outdoor temperature values  decreases the current set value
13. Measuring station wireless symbol
14. Battery compartment
15. Recess for wall mounting
16. Base
B Measuring station
17. Recess for wall mounting
18. Battery compartment
---|---

Explanation of Warning Symbols and Notes

Warning
This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes.

Package Contents

• ‘Action’ weather station (base station for indoors /measuring station for outdoors)
• 5AAA Micro batteries
• These operating instructions

Safety Notes

• The product is intended for private, non-commercial use only.
• Use the product for its intended purpose only.
• Protect the product from dirt, moisture, and overheating, and only use it in an adry environment.
• Do not use the product in the immediate vicinity of heaters or other heat sources or in direct sunlight.
• Keep this product, like all electrical products, out of the reach of children!
• Do not operate the product outside the power limits given in the specifications.
• Do not use the product in areas where the use of electronic devices is not permitted.
• Do not use the product in moist environments and avoid splashes.
• Do not place the product near interference fields, metal frames, computers, TVs, etc. Electronic devices and window frames can negatively affect the functionality of the product.
• Do not drop the product and do not expose it to any major shocks.
• Do not modify the product in any way. Doing so voids the warranty.
• Keep the packaging material out of the reach of children due to the risk of suffocation.
• Dispose of packaging material immediately according to locally applicable regulations.

Warning –Batteries

• When inserting batteries, note the correct polarity (+ and -markings) and insert the batteries accordingly. Failure to do so could result in the batteries leaking or exploding.
• Only use batteries (or rechargeable batteries) that match the specified type.
• Before you insert the batteries, clean the battery contacts and the polar contacts.
• Do not allow children to change batteries without supervision.
• Do not mix old and new batteries or batteries of a different type or make.
• Remove the batteries from products that are not being used for an extended period (unless these are being kept ready for an emergency).
• Do not short-circuit batteries.
• Do not charge batteries.
• Do not throw batteries in a fire.
• Keep batteries out of the reach of children.
• Never open, damage, or swallow batteries or allow them to enter the environment. They can contain toxic, environmentally harmful heavy metals.
• Immediately remove and dispose of dead batteries from the product.
• Avoid storing, charging, or using batteries in extreme temperatures.

Getting Started

Note
Before use, ensure you insert the batteries in the measuring station first and then in the base station.
4.1 Insert batteries
Measuring station

• Open the battery compartment (19) and remove the contact breaker.
• Then close the battery compartment cover.

Base station

• Remove the screen protector from the display.
• Open the battery compartment (14) and insert three AAA Micro batteries with the correct polarity.
• Then close the battery compartment cover.

4.2 Replacing the batteries
Note –Replacing the batteries

• Note that the stations have to be resynchronized each time after you change the batteries in the measuring or base station.
• To do this, remove the batteries from the other station and then reinsert them, or change them as required.

Measuring station

• Open the battery compartment (18), remove and properly dispose of the depleted batteries, and insert two new AAA Micro batteries with the correct polarity. Then close the battery compartment cover.

Base station

• Open the battery compartment (14), remove and properly dispose of the depleted batteries, and insert three new AAA Micro batteries with the correct polarity. Then close the battery compartment cover.

Installation

Note –Installation

• We recommend initially placing the base and measuring stations in the intended locations without installing them and making all the settings described in 6. Operation –todo.
• Only install the stations once the appropriate settings have been made and an astable wireless connection is established.

Note

• The wireless transmission range between the measuring and base stations is up to 50 min open spaces.
• Before installation, ensure that wireless transmission will not be disrupted by interference or obstacles like buildings, trees, vehicles, high-voltage lines, etc.
• Before the final installation, ensure that there is sufficient reception between the intended installation locations.
• When installing the measuring station, ensure that it is protected from direct sunlight and rain.
• The international standard height for measuring air temperatureis1.25 m(4ft) above ground.

Warning

• Buy special or suitable installation material from a specialized dealer for wall-mounting.
• Ensure that no faulty or damaged parts are installed.
• Never apply force during installation. This could damage the product.
• Before installation, ensure that the chosen wall is suitable for the weight to be mounted, and make sure that there are no electrical wires, water, gas, or other lines at the installation site on the wall.
• Do not mount the product above locations where persons might linger.

5.1. Base station

• Use the base to position the base station (16) on a level surface.
• Alternatively, you can install the base station on a wall using the opening (15) on the back.

5.2. Measuring station

• You can also position the measuring station on a level outdoor surface.
• We recommend installing the measuring station securely on an outdoor wall.
• Install an anchor, screw, nail, etc. in the wall of your choice.
• Hang up the base/measuring station using the opening (17) intended for this purpose.

Operation

Note
Hold down the ‘CH |  ’button (10) or the ‘MEM | ’button (12) to select the values faster.

6.1. Connection to the measuring station

• After you insert the batteries, the base station automatically searches for a connection to the measuring station and performs the initial setup.

Note

• Initial setup takes approx. 2minutes.
• During connection, the wireless symbol on the measuring station will flash (13).
• Do not press any buttons during setup. Otherwise, values may not be transmitted correctly and there is risk of value errors and inaccuracies.
• The setup process is completed when the indoor (7/8) and outdoor (2/3) measurement data is displayed.
• The measured value is automatically updated by the base device about every 45 seconds.
• If the temperature is outside of the measuring range, –.- (lower than minimum temperature) or –.- (higher than maximum temperature) will appear on the temperature display.
• If the base station still does not receive a signal from the measuring station, press and hold the ‘CH | ’button (10) for approx. 3seconds to start the manual search for the signal.

Displayed continuously| Inactive – no signal reception

Note –Faulty transfer of measured values

• In isolated cases, interference -e.g. from a WLAN network, computer, or television set -can cause the transfer of measured values between the measuring station and the base station to fail.
• In this case, you must resynchronize the stations by briefly removing the batteries from both stations and reinserting them.
• If the measured values are not transferred again once the batteries are inserted, replace the batteries with new ones.
• If necessary, select a new location for the base station in order to avoid possible interference in the future.

6.2 Selecting the channel/other measuring stations
Note

• You can install two moremeasuring stations in addition to the included measuring station. Ensurethat the base and measuring stations areset to the same channel.
• Visit www.hama.com for suitable measuring stations.
• Press the ‘CH | ’button (10) to set the channel to that set on the respective measuring station. Channel 1, 2or3 is displayed

6.3Basic and manual settings
Manually setting the date/time

• Press and hold the ‘C/F |SET’button (11) for approximately 3seconds to make the following settings one after the other.
• Year
• Month
• Day
• 12/24-hour format
• Hour
• Minute
• To select the individual values, press the ‘CH | ’button (10) or the ‘MEM | ’button (12), and confirm each selection by pressing the ‘C/F |SET’ button (11).
• Press the ‘C/F |SET’button (11) to adopt the set value displayed and to skip.
• If you do not make an entry for 8seconds, you automatically exit Settings mode.

6.4 Celsius/Fahrenheit

• Press the ‘C/F |SET’ button (11) when in any mode to choose between °C (Celsius) and °F (Fahrenheit).

6.5 Temperature measurement, maximum/minimum

• Press the ‘MEM | ’button (12) to display the maximum or minimum values for temperatureand humidity recording.
• If you press the ‘MEM | ’button (12) once, the maximum temperatureand humidity values are displayed. When you press the button once more, the minimum values are
  displayed.

6.6 Resetting data

• Press and hold the ‘MEM | ’button (12) for approximately 3seconds to reset the stored maximum and minimum values for indoor temperature(2), room humidity (3), outdoor temperature(2), and outdoor humidity (3).

6.7 Weather forecast

• The weather station shows the trend of the weather for the next 8hours using the following weather symbols:

Care and Maintenance

Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents. Make sure that water does not get into the product.

Warranty Disclaimer

Hama GmbH &CoKG assumes no liability and provides no warranty for damage resulting from improper installation/ mounting, improper use of the product or failure to observe the operating instructions and/or safety notes.

 Technical Data

Weather Station|
---|---
Max. transmitting power| 1.5 V
5AAA Micro batteries
Measuring range for temperature| 0°C –50°C /32°F –122°F
Measuring range for humidity| 20% –95%
Max. number of measuring stations| 3
Range| Approx. 50 m

 Declaration of Conformity

Hereby, Hama GmbH &CoKG declares that the radio equipment type [00186412] is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: www.hama.com->00186412->Downloads.

Recycling Information

Note on environmental protection:
After the implementation of the European Directive 2012/19/EU and 2006/66/EU in the national legal system, the following applies:
Electric and electronic devices, as well as batteries, must not be disposed of with household waste. Consumers areobliged by law to return electrical
and electronic devices, as well as batteries at the end of their service, lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual, or the package indicates that a product is subject to these regulations. By recycling, reusing the materials, or other forms of utilizing old devices/Batteries, you are making an important contribution to protecting our environment.

Hama GmbH &CoKG
86652 Monheim /Germany
Service &Support
www.hama.com
+49 9091 502-0

All listed brands are trademarks of the corresponding companies. Errors and omissions excepted,
and subject to technical changes. Our general terms of delivery and payment are applied.
00186412/07.21

References

• hama.com
• hama.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>