hama 00040072 Big Zapper Universal Remote Control Instruction Manual
- June 6, 2024
- Hama
Table of Contents
THE SMART SOLUTION
00040072
X1040072
Universal Remote Control
Big Zapper
Universal Fernbedienung
2in1
Art.Nr.: 00040072 /X1040072
Operating Instructions
Thank you for your decision about the Hama product. Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference.
Function buttons
- ON/OFF /LED Indicator
- Device selection keys
- Vol+/- Volume settings
- Mute
- Number keys 0-9
- -/– switch to two-digit channel numbers
- Setup –Remote control settings
- Menu –to enter On-screen menu
- AV –Select external AV source
- To confirm a selection
- Exit –to exit on-screen Menu
- CH +/- -Channel Selection
Explanation of the Note symbol
Warning
This symbol is used to indicate safety instructions or to draw your attention
to specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes.
Package Contents
- Universal Remote Control (URC)
- Code List
- This operating instruction
Safety notes
- Do not use the Universal Remote Control in moist or wet environments and avoid spray-water contact.
- Do not expose the Universal Remote Control to heat sources or direct sunlight.
- As with all electrical devices, keep the Universal Remote Control away from children.
- This product is intended for private, non-commercial use only.
- Use the product for its intended purpose only.
- Protect the product from dirt, moisture, and overheating, and only use it in an adry environment.
- Do not use the product in areas where the use of electronic devices is not permitted.
- Do not drop the product and do not expose it to any major shocks.
- Do not modify the product in any way. Doing so voids the warranty.
- Keep the packaging material out of the reach of children due to the risk of suffocation.
- Dispose of packaging material immediately according to Mlocally applicable regulations.
- Do not operate the product outside the power limits given in the specifications.
- Do not open the device or continue to operate it if it becomes damaged.
- Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
- Use the item only in moderate climatic conditions.
Warning –Batteries
-
When inserting batteries, note the correct polarity (+ and -markings) and insert the batteries accordingly.
Failuretodosocould results in the batteries leaking or exploding. -
Only use batteries (or rechargeable batteries) that match the specified type.
-
Before you insert the batteries, clean the battery contacts and the polar contacts.
-
Do not allow children to change batteries without supervision.
-
Do not mix old and new batteries or batteries of a different type or make.
-
Remove the batteries from products that are not being used for an extended period (unless these are being kept ready for an emergency).
-
Do not short-circuit batteries.
-
Do not charge batteries.
-
Do not throw batteries in a fire.
-
Keep batteries out of the reach of children.
-
Never open, damage, or swallow batteries or allow them to enter the environment. They can contain toxic,
environmentally harmful heavy metals. -
Immediately remove and dispose of dead batteries from the product.
-
Avoid storing, charging, or using the device in extreme temperatures and extremely low atmospheric pressure (for example, at high altitudes).
Getting started –Installing the Batteries
Note
• Alkaline batteries are recommended. Use 2„AA“(LR 6/Mignon) type batteries.
• Remove the battery compartment lid on the back of your URC (A).
• Check the required battery polarity and insert batteries according to the
“+/–” marks inside the compartment (B).
• Close battery compartment lid (C).
Note –Code saver
This remote control saves the settings during battery change.
Note –Battery saving function
The remote control switches off automatically when a button is pressed down
for more than 15 seconds. This
conserves battery power if the remote control gets stuck in a position where
the buttons are continually pressed down, such as between sofa cushions.
Setup
Note
- To obtain a proper infrared (IR) transmission, always point your Remote control in the approximate direction of the device you want to control.
- No entry for approx. 30 seconds will time out the Setup mode. The LED indicator shows six flashes and turns off.
- If you want to control a device, it´s not possible while the Universal Remote Control is in the Setup Mode.
Exit the Setup mode and select the device you want to control using the device selection keys.
5.1 Direct Code Entry
Your Universal Remote Control Package contains a code list. The code list
shows 4-digit codes for most TV/STB manufacturers in alphabetical order. If
the device you want to control is covered
by the code list, the Direct Code Entry is the most convenient entry method.
5.1.1 Turn on the device you want to control
5.1.2 Press the SETUP key until the LED indicator is permanently lit.
5.1.3 Select the device you want to control using the device key (e.g. TV). A
successful selection is indicated by the LED with one flash followed by
permanent light.
5.1.4 Check code list for brand and type of the device you want to control.
5.1.5 Enter the corresponding 4-digit code using the 0–9 keys. The LED
indicator confirms each entered digit via a short flash and turns off after
the fourth digit.
Note
• If the code is valid, it is saved automatically.
• If the code is invalid, the LED indicator flashes six times and then turns
off. Repeat steps 5.1.1 to 5.1.5 or use a different code entry method.
5.2 Manual code search
Your Universal Remote Control is equipped with an internal memory, which is
preloaded with up to
350 codes per device type for the most common
TV/STB devices. You can zap through these codes until the device you want to
control shows a reaction. This might be that the device you want to control
switches off (POWER key) or changes the channel (CH+/CH- keys).
5.2.1 Turn on the device you want to control
5.2.2 Press the SETUP key until the LED indicator is permanently lit.
5.2.3 Select the device you want to control using the device key (e.g. TV). A
successful selection is indicated by the
LED with one flash followed by permanent light.
5.2.4 Press the “POWER” or the CH+/CH- key to zap through the preloaded codes
until the device you want
to control reacts.
5.2.5 Press MUTE to save the code and exit the code search. The LED indicator
turns off.
Note
Internal memory limitations allow only up to 350 most common device codes to
be preloaded. Due to the
extensive number of different available TV/STB devices on the market, it may
be possible that only the most common main functions are available. If so,
repeat steps 5.2.1 to 5.2.5 to find a more compatible code. No code may be
available for some special device models.
5.3 Auto Code Search
Auto Code Search uses the same preloaded codes as the Manual Code Search (5.2)
but your Universal Remote Control scans through the codes automatically until
the device you want to control shows a reaction. This might be that the device
you want to control switches off (POWER key) or changes the channel (CH+/CH-
keys).
5.3.1 Turn on the device you want to control
5.3.2 Press the SETUP key until the LED indicator is permanently lit.
5.3.3 Select the device you want to control using the device key (e.g. TV). A
successful selection is indicated by the
LED with one flash followed by permanent light.
5.3.4 Press the CH+/CH- keys or POWER to start the Auto Code Search. The LED
indicator flashes once followed by permanent light. The Universal Remote
Control has a latency of 6seconds before the first scan starts.
Note –Scan Speed Settings
Scan Speed Settings can be set at either 1or3seconds.
The default setting for the scan time per single code is 1 sec. If this feels
uncomfortable, you can switch to 3sec. scan time per single code. To switch
between the scan times, press CH+ or CH- during the 6sec. latency before auto
Code Search starts scanning.
5.3.5 The LED indicator confirms each single code scan with a single flash.
5.3.6 Press MUTE to save the code and exit the code search.
The LED indicator turns off.
5.3.7 To stop the Auto Code Search during the scan process, press the EXIT
key.
Note
When all codes are searched without success, the Universal
Remote Control exits Auto Code Search and returns to operational mode
automatically. Currently, the stored code is not changed.
5.4 Code Identification
The Code identification offers you the possibility, to determine an already
entered code.
5.4.1 Press the SETUP key until the LED indicator is permanently lit.
5.4.2 Select the device you want to control using the device key (e.g. TV).
Successful selection is indicated by the LED with one flash followed by
permanent light.
5.4.3 Press SETUP key. The LED indicator flashes once followed by permanent
light.
5.4.4 To find the first digit, press the numeric keys from 0to
9. The LED indicator flashes once to indicate the first digit of the 4-digit
code number.
5.4.5 Repeat step 5.4.4 for the second, third, and fourth digits.
CODES
TV| SAT
|
Special Functions
6.1 Punch Through Channel
The Punch Through Channel allows the CH+ or commands to bypass the currently
controlled device and
switch the channels on a second device. All other commands remain
uninfluenced.
To activate the punch through channel setting:
- Press desired device mode key (e.g. TV).
- Press and hold the “CH+” key.
- Press desired device mode key (e.g. SAT).
- Release “CH+” (the indicator flashes once if the setting is activated).
To deactivate the punch through channel setting:
- Press desired device mode key (e.g. TV).
- Press and hold the “CH-” key.
- Press desired device mode key (e.g. SAT).
- Release “CH-” (the indicator is flashing twice if the setting is deactivated).
6.2 Punch Through Volume
The Punch Through Volume allows the VOL+ or VOLcommands to bypass the
currently controlled device and adjust the volume on the second device. All
other commands remain uninfluenced.
To activate the punch through volume setting:
- Press desired device mode key (e.g. TV).
- Press and hold the “VOL+” key.
- Press desired device mode key (e.g. SAT).
- Release “VOL+” (the indicator flashes once if the setting is activated)
To deactivate the punch through volume setting:
- Press desired device mode key (e.g. TV).
- Press and hold the “VOL-” key.
- Press desired device mode key (e.g. SAT).
- Release “VOL-” (the indicator is flashing twice if the setting is deactivated).
6.3 Macro Power
MacroPower enables you to turn two TV/STB devices on/off simultaneously.
To activate the micropower setting:
- Press desired device mode key (e.g. TV).
- Press and hold the “POWER” key.
- Press desired device mode key (e.g. SAT).
- Release “POWER” (the indicator flashes once if the setting is activated).
To deactivate the macro power setting:
- Press desired device mode key (e.g. TV).
- Press and hold the “POWER” key.
- Press desired device mode key (e.g. SAT).
- Release “POWER” (the indicator is flashing twice if the setting is deactivated).
Learn Mode
This remote control is equipped with a learning function.
Thus, you could learn the functions of your original remote to this remote
control.
7.1 Before Starting Learn Mode
- The batteries in the two remote controls have to be in good condition. Replace them if necessary.
- Place the remote controls with the infrared diodes so that they point towards each other.
- Where necessary adjust the height of both remotes so that infrared diodes are properly aligned.
- The distance between the remote controls should be about 3cm.
Note
- Do not move the remote controls during the learning procedure.
- Ensure that the room is not lit by fluorescents tubes or low energy consumption lamps since such light sources could interferewith the copying.
- The 2remote controls must be at least 1meter away from any light source.
- During learning mode, if no key is selected for morethan 30 seconds, the learning mode will exit automatically or if no other remote signal is received.
- Each function key will hold only one command. Anew command to be learned will automatically replace the previous one.
- It is not possible to learn any new functions to the TV, STB, and Setup key.
7.2 Enter Learn Mode
-
Press and hold the [MUTE] and [VOL+] keys for approx. 3seconds until the LED will be lit.
-
Enter the code [9] [8] [0], the LED will flash 2times and then remain on.
-
The Universal Remote Control is now ready to learn new commands.
7.3 Learning Of Keys
-
Press and release the desired key on the original remote control which you want the command to be learned. The LED at your Universal Remote Control will flash to confirm that the information has been received.
-
Then press and release the target key on the Universal
Remote Control you want to learn. -
If the LED flashes 3times and then remains on, the command has been learned successfully.
-
Repeat these steps to learn other key functions.
-
Please press the [SETUP] key to save the code and exit learning mode.
Note
While replacing the batteries, the remote control will keep the functions of
the learned keys.
7.4 Cleaning Of Learned Keys
7.4.1 Cleaning Of One Learned Key
-
Press and hold [MUTE] and [VOL+] keys for 3seconds until the LED will be lit.
-
Enter the code [9] [8] [1], the LED will flash 2times and then remain on.
-
Press and release the desired key at the Universal
Remote Control which you want to clear the learned command. If the LED flashes 3times, the learned
the command has been cleared successfully.
7.4.2 Cleaning Of All Learned Keys
-
Press and hold [MUTE] and [VOL+] keys for 3seconds until the LED will be lit.
-
Enter the code [9] [8] [2], the LED will flash 2times and then remain on.
-
Press and release the [SETUP] key at the Universal Remote Control. If the LED flashes 3times, all commands have been cleared successfully.
Maintenance
- Do not mix new and used batteries for powering the Universal Remote Control, as old batteries tend to leak and may cause power drain.
- Do not use corrosive or abrasive cleaners on your Universal Remote Control.
- Keep the Universal Remote Control dust-free by wiping it with a soft, dry cloth.
Troubleshooting
Q. My Universal Remote Control does not work at all!
A. Check your TV/STB device. If the device’s main switch is turned off, your
URC cannot operate your device.
A. Check whether your batteries are inserted properly and are in the correct
+/- position.
A. Check whether you have pressed the corresponding device mode key for your
device.
A. If the batteries are low, replace the batteries.
Q. If several Device Codes are listed under the brand of my TV/STB device, how
can I select the correct Device Code?
A. To determine the correct Device Code for your TV/STB device, test the codes
one by one until most keys work properly.
Q. My TV/STB equipment responds only to some of the commands.
A. Try other codes until most keys work properly.
Recycling Information
Note on environmental protection:
After the implementation of the European Directive 2012/19/EU and 2006/66/EU
in the national legal system, the following applies: Electric and electronic
devices, as well as batteries, must not be disposed of with household waste.
Consumers are obliged by law to return electrical and electronic devices as
well as batteries at the end of their service lives to the public collecting
points set up for this purpose or point of sale. Details to this are defined
by the national law of the respective country. This symbol on the product, the
instruction manual, or the package indicates that a product is subject to
these regulations. By recycling, reusing the materials, or other forms of
utilizing old devices/ batteries, you are making an important contribution to
protecting our environment.
Hama GmbH &CoKG
86652 Monheim /Germany
Service &Support
www.hama.com
+49 9091 502-0
All listed brands are trademarks of the corresponding companies. Errors and omissions excepted, and subject to technical changes. Our general terms of delivery and payment are applied.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>