hama Universal Smartphone or Tablet Holder Instructions
- June 6, 2024
- Hama
Table of Contents
THE SMART SOLUTION
Universal Smartphone-/ Tablet- Holder
Universal Smartphone-/ Tablet- Halter
A
B 
C
D
Operating instruction
Thank you for choosing the Hama product.
Take your time and read the following instructions and information completely.
Please keep these instructions
in a safe place for future reference. If you sell the device, please pass
these operating instructions on to the new
owner.
-
Explanation of warning symbols and notes
Warning
This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes. -
Package contents
• Smartphone /tablet holder
• These operating instructions
Note
Please check the package contents for completeness before installing the holder and ensure that there are no faulty or damaged parts. -
Safety instructions
• The product is intended for private, non-commercial use only.
• Use the product only for the intended purpose.
• Do not use the product in a damp environment and avoid splashing water.
• Do not use the product in the immediate vicinity of heaters, other heat sources, or in direct sunlight.
• Do not attach any additional objects to the product.
• Keep the packaging material out of the reach of children due to the risk of suffocation.
Dispose of packaging material immediately in accordance with the locally applicable regulations.
• Do not modify the product in any way. Doing so voids the warranty.
• Observe the other warnings and safety instructions.
Warning
• Ensure that the product does not exceed its maximum permitted carrying capacity and that no-load exceeding the maximum permitted dimensions are attached.
• Make sure that the product is loaded symmetrically.
• During adjustment, ensure that the product is loaded symmetrically and that the maximum permitted carrying capacity is not exceeded.
• The product is used to set up smartphones, tablet PCs and similar or to attach them to tabletops and shelving. -
Installation
Warning -Mounting
• Only set the product up on even, non-slip surfaces with sufficient load- bearing capacity for the product and the device attached to it.
• Do not mount the product above locations where persons might sit or stand.
• Never apply force during mounting. This can damage your device or the holder.
• During mounting, ensure that neither there are no coils, hobs or other sources of moisture and heat in the area of the holder’s mounting or swivel range.
• Once you have mounted the product and the attached load, check that they are sufficiently secure, resilient and safe to use.
• You should repeat this check at regular intervals (at least every three months).
• In the event of damage to the product, remove the attached load and stop using the product.
4.1 Inserting /removing the device
• Spread the holding clamps on the holder far enough apart for you to be able to insert your device. (Fig. A)
• Hold the device firmly, position it between the holding clamps and then press the holding clamps gently together. (Fig. B)
• After insertion, check that the device is sitting firmly and securely in the holder.
• To remove your device, hold it firmly and carefully push the holding clamps apart.
4.2 Attachment to the tabletop /shelf
• Always affix the holder without the device inserted.
• Slightly open the closure on the holder by turning it anti-clockwise. (Fig. C)
• Position the holder in the required place on the tabletop. Turn the holder to adapt it to the thickness of the tabletop.
• Turn the closureclockwise to attach the holder.
• Check that the holder is firmly and securely seated. -
Adjusting the angle and tilt The holder can be steplessly adjusted in terms of angle and tilt with respect to the observer using a ball head.
• Always adjust the angle and tilt without the device being inserted.
• To adjust, loosen the clamp screw on the ball head. (Fig. D)
• Adjust the angle and tilt as required and tighten the clamp screw.
• The holder arm can also be adapted to the required height. -
Technical data
00210538 –Smartphone holder
| Up to max. tabletop thickness | 7cm |
|---|---|
| Adjustable height | max. 65 cm |
| Holding bracket width | 6–8cm |
00210539 –Tablet holder
| Up to max. tabletop thickness | 6.5 cm |
|---|---|
| Adjustable height | max. 75 cm |
| Holding bracket width | min. 13.5 cm |
max. 22 cm
7. Warranty Disclaimer
Hama GmbH &CoKGassumes no liability and provides no warranty for damage
resulting from improper installation/mounting, improper use of the product or
from failure to observe the operating instructions and/ or safety notes.
Hama GmbH &CoKG
86652 Monheim /Germany
Service &Support
www.hama.com
+49 9091 502-0
All listed brands are trademarks of the corresponding companies.
Errorsand omissions excepted and subject to technical changes.
Our general terms of delivery and payment are applied.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>