ZbeamZ SLIMPAR 30W Datasheet
- June 6, 2024
- ZbeamZ
Table of Contents
BEAMZ MADE EAZY
150.903 V1.1
SLIMPAR 30W
QUICK STAR GUIDE
UNPACKING INSTRUCTION
CAUTION
Immediately upon receiving the product, carefully unpack the carton, check
the contents to ensure that all parts are present, and have been received in
good condition. Notify the shipper immediately and retain the packing material
for inspection if any parts appear damaged from shipping or the package itself
shows signs of mishandling. Save the package and all packing materials. In the
event that the product must be returned to the factory, it is important that
the product be returned to the original factory box and packed.
If the unit has been exposed to drastic temperature fluctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation
water might damage your unit. Leave the unit switched off until it has reached
room temperature.
POWER SUPPLY
On the label on the backside of the unit is indicated on this type of power
supply must be connected. Check that the mains voltage corresponds to this,
all other voltages than specified, the light effect can be irreparably
damaged. The product must also be directly connected to the mains and may be
used. No dimmer or adjustable power supply.
WARNING
Always connect the unit to a protected circuit (circuit breaker or fuse).
Make sure the unit has an appropriate electrical ground to avoid the risk of
electrocution or fire.
RIGGING
The unit may be set up on a stable and even surface. By means of the fixing
facilities of the baseplate, the unit can also be mounted upside down to a
truss, see the below picture. For fixing, certified clamps with correct save
working load are required. According to the figure, the quick-lock bolts of
the omega brackets are placed into the openings provided in the base plate and
turned clockwise until they lock (to the stop). The mounting place must be of
sufficient stability and be able to support a weight of 10 times the unit’s
weight. Secure the unit with a safety cable so that it cannot fall down.
When carrying out any installation, always comply with European and national
guidelines concerning rigging, truss, and all other safety issues. Always let
the installation be checked out by an authorized dealer!
REMOTE CONTROLLER
BLACKOUT MODE
Press{BLACK OUT} off existing modes. Press return the last modes.
AUTO MUDE
Automatic mode will enable you to run the automatic programs on the
product.
To turn on Automatic mode:
- Press {auto} on the remote controller.
- Press {+} or {-} to choose between the different auto programs.
SUND MUDE
The sound-Active mode will enable the product to respond to the music.
To turn on Sound-Active mode:
- Press {SOUND} on the remote controller.
- Press {+} or {-} to choose between the different sound programs.
STROBE MODE
To adjust the strobe speed of the automatic program and the sound active
program.
- Press < STROBE) on the remote controller.
- Press < +> or <-> to either increase or decrease the speed of the program.
- Press < STROBE> again to turn off the strobe.
SPEED MODE
To adjust the speed of the automatic program and the sound active program.
- Press < SPEED) on the remote controller.
- Press < +> or <-> to either increase or decrease the speed of the program.
SENSITIVITY MODE
To adjust sound sensitivity for in Sound-Active mode
- Press < SENSITIVITY> on the remote controller.
- Press [-] or <-> to either increase or decrease sound sensitivity.
MANUAL MODE
- Press < MANUAL> on the remote controller.
- Press < W>, <0>,
(cool white, warm white, or UV) to choose your color.\ - Press again < kb, <0>, <UV) (cool white, warm white, or UV) to close your color.
- Press < +> or <-> to either increase or decrease the percentage of each color.
FADE/UNIT MODE
To adjust the FADE speed of the automatic program. the sound active program
and the manual mode.
1. Press < FADE> on the remote controller.
2. Press < FADE> again to turn off the Fade mode.
NUMBER 1-9
To adjust the brightness value of the automatic program. the Sound active
program and Manual Mode. Press digit (1 > to (9 > to change different
brightness on the device.
CAUTION!
The remote control is supplied with a battery inserted. An insulating foil
between the battery and the battery contacts prevents the battery from being
discharged during storage. Prior to the first operation remove the foil from
the battery support on the rear side of the remote control. Otherwise, the
operation of the remote control is not possible.
If the range of the remote control decreases. replace the battery. For this
purpose. on the rear side of the remote control press, the small bar with the
groove to the right (1) and at the same time remove the battery support (2).
For operation. one 3 V button cell type CR 2025 is required. When inserting.
pay attention that the positive pole of the button cell shows upwards in the
support
BEAMZ
YOUR FUTURE
YOUR SKILLS
YOUR PLATFORM
is a leading developer of lighting products, including intelligent DMX moving heads, wireless battery operated DMX eFFects, static washes, sound-activated club eFFects, strobes & blacklights, LED lighting, fog and special effects machines, lasers, and indoor and outdoor architectural lighting, as well as lighting controllers and protective bags.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>