SOCKET 600 Series Charging Stand User Guide
- June 6, 2024
- Socket
Table of Contents
- SOCKET 600 Series Charging Stand
- PACKAGE CONTENTS
- PRODUCT INFORMATION
- ATTACHING THE SECURITY CABLE
- INSERTING THE POST TO THE BASE
- CHARGING STAND OPERATIONS
- OPTIONAL TABLE MOUNTING
- COMMAND BARCODES
- AUTO SCANNING MODE
- PRODUCT SPECIFICATIONS
- HELPFUL RESOURCES
- COMPLIANCE STATEMENT
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SOCKET 600 Series Charging Stand
PACKAGE CONTENTS
Optional
©2021 Socket Mobile, Inc. All rights reserved. Socket®, the Socket Mobile
logo, SocketScan®, DuraScan®, Battery Friendly® are registered trademarks or
trademarks of Socket Mobile, Inc. Microsoft® is a registered trademark of
Microsoft Corporation in the United States and other countries. Apple®, iPad®,
iPad Mini®, iPhone®, iPod Touch®, and Mac iOS® are registered trademarks of
Apple, Inc., registered in the U.S. and other countries. The Bluetooth®
Technology word mark and logos are registered trademarks owned by the
Bluetooth SIG, Inc. and any use of such marks by Socket Mobile, Inc. is under
license. Other trademarks and trade names are those of their respective
owners.
PRODUCT INFORMATION
Illuminates Red when connected to AC Power.
ATTACHING THE SECURITY CABLE
Security cable comes Pre-installed for your convenience. To remove, follow step 2 and step 1.
INSERTING THE POST TO THE BASE
Insert the post into the top of the base, lining up the marker on the post to
the unlock icon. Push down and turn the post towards the lock icon until you
hear a click. Run the USB cord through the
channel at the bottom of the base.
CHARGING STAND OPERATIONS
The charging pins must align to supply power to the scanner. The red light will illuminate and the scanner will beep twice.
When set to Auto Scan with Socket Mobile’s 2D barcode scanners (D740, D745, D750, D755, D760, S740, S760), the barcode should be 4 to 8 inches away.
OPTIONAL TABLE MOUNTING
Two keyholes are provided on the Charging Stand base for an optional installation on a wooden surface (screws and drill template included).
- Place the Charging Stand on the drill template and position these in the desired location. Rotate the Charging Stand to align with the solid notch (not the dotted notch) on the template.
- Rotate the Stand/template combination so the Socket Mobile logo faces the direction you want the scanner to aim.
- Tape the template to the surface and remove the Charging Stand.
- Drill two 3/32” holes through the drill marks on the template.
- Tighten the two screws with about 1/4” of the screw head exposed.
- Place the Charging Stand on the template aligned with the dotted notch.
- You can now tear away the template.
- Twist the Charging Stand clockwise to lock the screws in the keyholes.
COMMAND BARCODES
Charging Stand Modes
Auto Scan
Scan the barcode to enable Auto Scan. This will allow the scanner to
automatically scan barcodes without pressing the scan button.| 
Manual Mode – Normal (default)
Scan the barcode to configure the scanner back to normal. It will be in manual
scan mode even when placed in the stand or cradle.| 
Charging Stand Modes
**Stand Mode***
Scan the barcode to configure the scanner is permanently in Auto Scan mode, regardless whether it is connected to power or not.
| 
This mode will drain the battery faster if not connected to power.
AUTO SCANNING MODE
- Scan command barcode to place your scanner in Auto Scan. Note: Turn off host device’s Bluetooth before scanning command barcode.
- Once the scanner is in Auto Scan, it will switch to automatic scanning when it detects power coming from the charging pins of the Dock or Stand. Place a barcode in the scanners field of view and the scanner will automatically scan it.
Supported 2D Scanners:
D740, D745, D750, D755, D760, S740, S760
How Auto Scanning Mode Works in the Stand or Dock
| Action | Behavior | Notification |
|---|---|---|
| Beep Pattern | Light Activity | Vibrate |
| Place Scanner in the Stand | Scanner switches to Auto Scan Mode | High-high tone |
| confirms proper seating* | Battery Status Light is Disabled | None |
| Place a barcode in the Scanners Field of View | Decode barcode | 1 Beep when |
| Data successfully scanned | Green Light blinks (while scanning) | None |
How the Scanner reverts to Manual Mode (Not in the Stand)
| Action | Behavior | Notification |
|---|---|---|
| Beep Pattern | Light Activity | Vibrate |
| Remove the Scanner from the Stand and press the scan button | Scanner switches | |
| to Manual Mode | None | Battery Status Light is Enabled |
| Press the scan button | Decode barcode | 1 Beep when Data successfully scanned |
| Green Light blinks (while scanning) | Vibrate when Data successfully scanned |
Auto Scanning Mode: Barcodes placed in the Scanner’s field of view are
automatically scanned.
Manual Mode (default): Pressing the scan button initiates a scan.
PRODUCT SPECIFICATIONS
Dimensions
Stand Height| 6.5 in (165 mm)
Charging Mount Width| 1.80 in (46 mm)
Charging Mount Length| 5.50 in (140 mm)
Base Diameter| 5.75 in (146mm)
Total Weight
Without Scanner and Power Adapter| 12.7 oz (360 g)
HELPFUL RESOURCES
Technical Support and Product Registration:
support.socketmobile.com
Phone: 800-279-1390
+1-510-933-3020 (worldwide)
Warranty Checker: socketmobile.com/warranty-
checker
Socket Mobile Developer Program:
socketmobile.com/developer
Download Socket Mobile’s scanner User Guide and Command Barcodes at
socketmobile.com/downloads
COMPLIANCE STATEMENT
CE MARKING AND EUROPEAN UNION COMPLIANCE
The unit under test was found compliant with all the applicable Directives,
2004/108/EC and 2006/95/EC.
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
The WEEE directive places an obligation on all EU-based manufacturers and
importers to take-back electronic products at the end of their useful life.
ROHS STATEMENT OF COMPLIANCE
This product is compliant to Directive 2011/65/EU.
NON-MODIFICATION STATEMENT
Changes or modifications not expressly approved by the party responsible for
compliance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>