Godox SL150II BI Bi-Color LED Video Light Instruction Manual
- June 6, 2024
- Godox
Table of Contents
Godox SL150II BI Bi-Color LED Video Light Instruction Manual
IMPORTANT SAFETY INSTRUCTIONS
When using your photographic equipment, basic safety precautions should always be followed, including the following:
- Read and understand all instructions before using.
- Close supervision is necessary when any appliance is used by or near children. Do not leave appliance unattended while in use.
- Care must be taken as burns can occur from touching hot parts.
- The appliance switch is provided with the symbols 0 indicating off and 1 indicating on. The symbols and may be used for this purpose.
- Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged – until it has been examined by a qualified serviceman.
- Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
- If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat.
- Always unplug appliance from electrical outlet before cleaning and servicing and when not in use. Never yank cord to pull plug from outlet. Grasp plug and pull to disconnect.
- Let appliance cool completely before putting away. Loop cord loosely around appliance when storing.
- To reduce the risk of electric shock, do not immerse this appliance in water or other liquids.
- To reduce the risk of electric shock, do not disassemble this appliance, but take it to a qualified serviceman when service or repair work is required. Incorrect reassembly can cause electric shock when the appliance is used subsequently.
- The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire, electric shock, or injury to persons.
- Connect this appliance to a grounded outlet.
- Disconnect this unit from its source of supply before replacing the projection lamp.
- This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way.
SAVE THESE INSTRUCTIONS
Foreword
Thank you for purchasing this Godox Product! With 8 special effects modes, strong power, soft illumination and abundant functions, Bi-color LED Video Light SL150IIBi can achieve creative shooting easily.
Main Features:
- With color temperature adjustment from 2800K to 6500K.
- With 9 FX special effects mode to simulate various of shooting scene.
- Silent mode: without noises and interference.
- Built-in Godox 2.4G wireless & wirelessly adjust parameters.
- With stable light source and 0% to 100% precise light adjustment.
- With 16 groups and 32 channels wireless control.
- With U-type bracket to adjust different angles easily.
- Bowens-mount enables to install various of accessories.
- Clear LCD display.
- Excellent heat dissipation.
Warning
Always keep this product dry. Do not use in rain or in damp conditions.
Do not disassemble. Should repairs become necessary, this product must be sent
to an authorized maintenance center.
Keep out of reach of children.
As this product do not have waterproof function, please take measures of
waterproof in rainy or damp environment.
Do not use the product in the presence of flammable gases, chemicals and other
similar materials.
CAUTION: Hot parts! When the product is always on and flickering, please do not touch the high temperature part of the LED head. When replacing product accessories, please turn off the LED light and perform a cold cut.
Name of Body
Remote Control
LCD Panel
Included Items
-
Body 1 Frosted Cover 1
-
*Reflector 1
** -
*Protect Cover 1
** -
*RC-A6 Remote Control 1
** -
*Power Cable 1
** -
*Instruction Manual 1
**
Separately Sold Accessories
The product can be used in combination with the following accessories sold separately, so as to achieve best photography effects: Power Inverter, Softbox, Photographic Umbrella, Light Stand, Barndoor, Snoot, etc
Power Connection
Use the power cord to connect the LED light to an AC power source and turn on the power switch.
Operation
Mode Selection
LED silent mode: in this mode, the fan is turned off. There is no noises and interference in this mode.
LED special effects modes: Short press the FX button to enter or exit the
special
effects. When entering the FX modes, FX icon will be displayed on the LCD
panel. Then, turn the FX select dial to choose one mode from the 9 special
effects modes to achieve creative shooting.
| Display | FX1 | FX2 | FX3 | FX4 | FX5 | FX6 | FX7 | FX8 | FX9 |
|---|---|---|---|---|---|---|---|---|---|
| Scene | Flash1 | Flash2 | Stornn1 | Storm2 | TV | Broken bulb | Camdle | Fire |
Firework
Note: Only 6500K color temperature can be displayed in special effects mode.
LED strong power mode : turn on the fan to enter LED strong power mode and the power will up to the maximum value in this mode.
Light Brightness Adjustment
In LED mode, the light brightness of LED light can be adjusted by turning the
DMX select dial from 0% to 100%. And the light brightness will be clearly
displayed on the LCD Panel.
Color Temperature Adjustment
In continuous LED mode, turn the CCT/FX select dial to adjust color
temperature from 2800K to 6500K. And the color temperature value will be
precisely displayed.
Group GR, Channel CH and ID Setting
GR Setting: Short press GR button to choose group from A, B, C, D, E, F and 0 to 9.
CH Setting: Short press CH button to choose channel from 1 to 32
ID Setting: Long press GR and CH button to enter ID setting interface. Then, turn the DIM select dial to choose ID from OF and 01 to 99.
Wireless Control
With 2.4G wireless system, Bi-color LED Video Light SL150IIBi have receive and control function. Up to multiple groups of LED lights can be controlled. 32 channels and 99 wireless IDs are available with strong anti-interference capability. Please set the channels, groups and IDs of LED light to the same as those of RCA6 remote control before usage
Adjusting Channel/Group with the Remote Control
- Press the CH/GR button and the group icon blinks. Press the“-”“+”button to choose a group (A to F, 0 to 9).
- Press the CH/GR button twice and the channel icon blinks.
Press the“-”“+”button to choose a channel (1 to 32).
Adjusting ID with the Remote Control
- Double click the CH/GR button and press the“-”“+”button to choose ID from OFF or 01 to 99. Adjusting Light Brightness with the Remote Control
- Press the“-””+“button to adjust the light brightness.
Adjusting Color Temperature with the Remote Control
- Press the SET button of the remote control and the color temperature icon blinks. Press the“-”“+”button to adjust the color temperature.
Remote control reset: press down “-” and “+” button simultaneously to reset.
Note: The wireless signal can be received only when the controller of LED light is powered on.
Setting color temperature range
The factory setting of remote control’s color temperature range is 2800-6500K. In order to use remote control conveniently, color temperature range settings are added: when the remote control is off, hold down the SET button and turn it on to enter color temperature adjusting interface. Press CH/GR button to switch the lowest and highest color temperature value and press “-” or “+” button to change the value. Press the SET button to confirm it.
Technical Data
| LED Video Light | SL15011Bi |
|---|---|
| Power Supply | AC100V-240V(50/60HZ) |
| Output Power | 150W |
| Color Temperature Range | 2800-6500K |
| 100% Light Brightness(LUX,1M) | =.30000 |
| CRI i–––—– | 96 |
| TLCI –zi | 97 |
| Light Brightness Range | 0%-100% |
| Operation Temperature | -10 -40°C |
| Channel | 32 |
| Group | 16(A, B, C, D, E, F, 0-9) |
| Dimension (not included a standard reflector) | 34x20x16cm |
| Net Weight(not include reflector and protect cover) | 3.07Kg |
| Remote Control | RC-A6 |
| --- | --- |
| Power Supply | 3.0V(AAA*2)(not include) |
| Wireless Frequency | 2.4GHz |
| Distance (emptiness) | 50m |
| Channel | 32 |
| Group | 16 groups(A-F, |
| Standby Time | Over one year |
| Operation Temperature | -10 – 40°C |
| Dimension | 120*3815mm |
| Net Weight | 30g |
Product design and specifications are subject to change without notice.
Maintenance
This product, except consumables e.g. cable, is supported with a one-year warranty. Avoid sudden impacts and the product should be dedusted regularly. Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories. Unauthorized service will void the warranty. If the product had failures or was wetted, do not use it until it is repaired by professionals. Changes made to the specifications or designs may not be reflected in this manual.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation..
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>