HONOR R3-FT400 Radio Car Bluetooth Box User Manual
- June 6, 2024
- Honor
Table of Contents
R3-FT400 Bluetooth Box User Manual
V1.3 （October 25, 2020）
After June 2020, the Bluetooth module supports SPP and BLE
The role of the Bluetooth box:
The Bluetooth box has a built-in Bluetooth module. The APRS beacon data
decoded by the FTM400 or FTM100 is output to the Bluetooth module in the box
through the
10-pin to 6-pin cable. The APRs software is installed on the mobile phone or
tablet to search for the Bluetooth module in the connection box. For example,
APRSDROID is
connected to the Bluetooth box. The beacon received by the FT400 or FT100 can
be transmitted to the APRSDROID to see the map position, direction distance,
etc.
Supported platform models: FTM-400D, FTM400XDR, FTM-100D *You can also use DIY
other cables to connect to KenwoodTM-D710 or other APRS stations with PACKET
or NMEA WAYPOINT output.
FT M-400D Set the use steps:
1，Connect the FTM400 or FTM100 radio and power supply according to the
picture.
2，Set the serial output format of the radio station to: WAYPOINT or PACKET, rate: 9600 For example, the FTM400 settings are shown in the picture：
Select： waypoint, the beacon output has a call sign and GPS coordinates。
Select: packet, the beacon output has a call sign, GPS coordinates, and beacon text。
3, mobile phone Bluetooth pairing, search conversion box
Bluetooth name : FT400BT-SPP or FT400BT-BLE
pairing password: 1 234
Note1: IOS system uses FBT400-BLE, Android system uses FBT400-SPP or
FBT400-BLE
The red LED inside the box will flash or light up when the power is on. If
there is no flash or long light, there is no power supply to the box.
Red LED Blink = Bluetooth is not connected
Red LED Long light = Bluetooth is connected
4. After the Bluetooth pairing is completed, the APRS program can be used in
conjunction with (NMEA WAYPOINT format).
The APRS program APRSDROID is set as follows：
Connection protocol selection: NMEA waypoint Link type selection: Bluetooth
SPP Device selection: FT400BT-SPP
Note2: APRSDROID program can only choose” NMEA waypoint”； Other APRS APP, please test and verify by yourself！
|
---|---
After the setting is completed, enable: start Tracking. At this time, the red indicator light inside the Bluetooth converter box is long, indicating that the APRSDROID is connected to the Bluetooth converter box. When the FT400 receives the decoded beacon, it will immediately transmit to the APRSDROID via Bluetooth. To the APRS list, you can also see the specific location or trajectory of the other party through the APRS map in real-time. Note 3: The APRSDROID version of the above screenshot is the OSM version.
iPhone test FT400BT-BLE (October 25, 2020) Test Conditions: iPhone 7 IOS version: 10.3.2
Note 4: In the IOS system, R3 internal Bluetooth BLE mode does not
support Bluetooth manager search. The APP needs to support the Bluetooth BLE
mode, and the R3-BLE connection will be automatically found in the APP
R3 Bluetooth serial port transparent transmission test 1, Serial debugging APP
name: JDY-LED or LIGHTBLUE, Download in the Apple Store.
JDY-LED is Installed normally.
LIGHT BLUE Installation prompt, Apple system version is low and not supported
Below is a screenshot of the JDY-BLE test
Left picture: APP found BLE,
Right: FT400 receives APRS beacon data and transmits it to APP via BLE
Name : FT400BT- BLE
MCA: 20:07:23:20:23:FE
RSSI:-60
Note5: JDY-LED is only to verify that the Bluetooth BLE mode is used normally. It is not an APRS application
R3 Bluetooth BLE test 2: APRS software test
APP name: OvitalMap
APP URL: https://www.ovital.com/ https://en.ovital.com/
Note 6: Accepted by China’s Apple ID, only China’s APP test
Enter the peripheral device manager, select Bluetooth
Left picture: ” OvitalMap ” peripheral device manager, Bluetooth device scan,
search list has FT400BT-BLE
Right picture: ” OvitalMap ” peripheral device manager, select “FT400BT-BLE”,
and automatically bind the Bluetooth device “FT400BT-BLE”
Choice: Universal APRS device, the default communication mode of the program is KISS, compatible with FT400 radio output KISS
Peripheral Device Manager, BLE is connected
OvitalMap l, normal use in China. I don’t know if it can be used in other
regions. Please find the APRS program available
in the current region to connect “R3-BLE”
This manual download URL： http://avrtx.cn/ File Directory：
R3
BH7NOR E-MAIL: [email protected];
[email protected]
October 25, 2020