HomeSeer HS-DS100+ Z-Wave Door / Window Sensor User Guide
- June 6, 2024
- HomeSeer
Table of Contents
HS-DS100+ Z-Wave Door / Window Sensor
OVERVIEW
HS-DS100+ is a battery-operated sensor that is designed to issue Z-Wave commands when doors or windows are opened or closed. HS-DS100+ may be associated directly with other Z-Wave devices or it may be used with a wide variety of Z-Wave hubs and controllers to trigger events, scenes, and other automation.
Operation
HS-DS100+ is comprised of a sensor body and a magnet piece. The sensor body is (typically) installed on a door or window jamb. The magnet piece is (typically) installed on the door or window. When the door or window are closed, the magnet trips a switch inside the sensor body and a Z-Wave command is issued. When the door or window are opened, the switch is tripped again and another Z-Wave command is issued.
Physical Installation
The sensor body and magnet piece must be mounted to the door or window (vertically or horizontally) using the provided crews or double-stick tape (your choice). Leave a gap (no wider than 10mm) to allow the door or window to open and close easily without obstruction. If using screws, you’ll have to the mount the backing plates of the sensor body and magnet pieces first. To do this, press the latch button on the sensor body and gently pry off the backing plate (the plate can be difficult to remove). Then, use a small slotted screwdriver to remove the backing plate from the magnet piece.
Z-Wave Network Installation
Door/Window Sensor can be included and operated in any Z-Wave network with
other Z-Wave certified devices from other manufacturers and/or other
applications. All non-battery-operated nodes within the network will act as
repeaters regardless of the vendor to increase the reliability of the network.
Inclusion (Use this procedure to add the HS-DS100+ to your Z-Wave
network).
- Ensure AAA batteries are installed. Remove any plastic from the battery compartment (if necessary)
- Put your home automation controller into ‘inclusion’ mode. Consult your system’s manual for details.
- Triple-click the Z-Wave button inside the sensor body. Wait for the process to finish.
- If successful, the sensor body LED will blink briefly and then stay on for 3 seconds. If unsuccessful, the LED blinks briefly and then turns off. Should this happen, repeat the inclusion process.
Note: If you want this Door/window sensor to function as a security
device using secure/encrypted Z-Wave communications, then a security-enabled
Z-Wave controller is required.
Exclusion (Use this procedure to remove the HS-DS100+ from your Z-Wave
network).
- Put your home automation controller into ‘exclusion’ mode. Consult your system’s manual for details.
- Triple-click the Z-Wave button inside the sensor body. If successful, the LED will turn off within 1 second. If unsuccessful, the LED blinks for 5 seconds. Should this happen, repeat the exclusion process.
Reset (Use this procedure to reset the HS-DS100+ to factory default settings when the network primary controller is missing or otherwise inoperable).
- Press and hold the Z-Wave button inside the sensor body for 20 seconds, the LED will stay on until releasing the button.
Z-Wave Association Information
HS-DS100+ supports Group 1 and Group 2 associations. Group 1 reports the
sensor’s condition, battery level and tamper state.
Group 2 sends the BASIC SET command.
Battery Information
HS-DS100+ is designed to report its battery condition once every 24 hours. A
battery level report can also be manually invoked by pressing the Z-Wave
button.
S2 Security
HS-DS100+ supports Z-Wave S2 security in unauthenticated mode.
ADDITIONAL INFORMATION
Please visit our website for the latest information about HS-DS100+
(https://homeseer.com/support-home/)
ADVANCED CONFIGURATION
| Parameter | Settings |
|---|---|
| 15 | Value of BASIC SET |
0-Sends 0xFF for open and 0x00 for closed
1-Sends 0x00 for open and 0xFF for closed
0-Default
1 byte—Parameter size
32| Defines value of LOW BATTERY
10-50 (10%-50%)
20-Default
1 byte—Parameter size
SPECIFICATIONS
Operating Temp Range| 0ºC to 40ºC| Power Supply| Requires (2) AAA 1.5V
Batteries
---|---|---|---
Z-Wave Frequency | Range Z-Wave Certification| 908 MHz (US) | Up To 300 Ft
line of sight
Z-Wave Plus| Dimensions| Sensor Body: 3 x 1.1 x .75 inches
Magnet Piece: 3 x .5 x .75 inches
LIMITED WARRANTY
HomeSeer Technologies, LLC will repair or replace, at its option, any part of the device, which proves to be defective in workmanship or material under normal use, in the USA except in the states of Alaska or Hawaii, for a period of one year from the date the device is purchased. During the warranty period, HomeSeer Technologies, LLC will repair and provide all parts necessary to correct such defects, free of charge, provided the device has been operated in accordance with the manufacturer’s guidelines. The Customer will return the device to HomeSeer Technologies, LLC for testing and repair or replacement. Should you need service, during the warranty period or beyond, contact HomeSeer to obtain return authorization before shipping your device to HomeSeer Technologies, LLC.
This product employs or practices certain features and/or methods of the
following U.S. Patents: U.S. Patent Nos.6,891,838, 6,914,893 and 7,103,511.
HomeSeer | 10 Commerce Park North, Unit 10 | Bedford, NH 03110 |
HomeSeer.com | Doc: HS-DS100-en-v2
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>