IMIC-ME20 Digital Thermometer Hygrometer User Manual

IMIC-ME20 Digital Thermometer Hygrometer User Manual

Introduction

Thank you for purchasing our Digital Thermometer-Hygrometer. Please take a few minutes to browse through this user manual before you begin to operate the meter to ensure that you are fully familiarized with how best to operate the meter as accurately and safely as possible. This product is for indoor use, only. It uses a high-speed microprocessor and a high-precision digital sensor, which can quickly and accurately measure the current environmental temperature and humidity. It is useful in homes, offices, warehouses, laboratories, greenhouses, etc.

Specifications

• Name lMlC Digital Thermometer-Hygrometer
• Model MIC— ME20
• Standard QB/WSDL ML2X-20a 9
• Temperature : -10 60.0 C(J4 140 L) ResoIution0.J °C Accuracy+0.3°C
• Humidity : 0 99%RH ResoIution1%RH Accuracy +3%RH
• Sample rate: default 5 seconds, Adjustable range 1- 60seconos
• Dimension : 80 x 80 x 13mm
• Weight : 62g
• Battery: CR 2032, DC3V

Panel information

1. Temperature display
2. Bluetooth ( optional)
3. Low power indicator
4. Humidity units
5. Comfort level indicator
6. Temperature units

Comfort Level Indicator

Comfortable
Normal
Uncomfortable

| Temperature <20’C| 20°CTemperature 27 C| Temperature›27’C
---|---|---|---
Humidity <25% or >75%|

25% < Humidity <75%|

|

|

Low power indicator

When the battery voltage drops below proper operation range. the symbol still appear on the LCD display and the battery  will need to be replaced

Back panel information

1. Magnet
2. Battery cover
3. Bracket
4. Battery insulation film
5. Settings button
6. CF switch button

Operation Instructions

• Install or Replace Battery
  first time u se, please pull out and discard the protective UI m under the battery.
  If you need to replace the battery, please install a CR2032 battery with the negative pole facing down, and replace the battery cover.

• Usage scenarios
  The product supports two scenarios: desktop mode and wall mode.
  
  

• Select Degrees Fahrenheit or Celsius
  Pres  the button to select degrees i n Fahrenheit it (”F) or Celsius (
  O C).

• Adjust Sampling Rate
  The default sample rate is 5 seconds after each power-on. If you need to adjust the increment, p res s S ET button for 5 second s to enter the setting mode. Press  the button to choose the sampling time between – 60 seconds. Set the meter for 10 seconds to save and exit automatically.

Note that the sample rate will affect the battery life, the shorter the cycle, the shorter the battery life. The following table is for reference only:

Precautions and notes

• Do not use in high temperature and humidity environment for an extended period of time.
• Avoid prolonged exposure to volatile chemicals.
• Please use gentle detergent to clean products surface if needed.
• Upon initial use, for a 30 minute lag li me for monitor to register the
  correct data.

Warranty instructions

Warranty ordinance
The after-sales service of this Thermo- hygrometer must be in strict accordance with the Amazon warranty.

Non-warranty Ordinance

1. Non-authorized maintenance dropping liquid contamination, etc.
2. Expiration of warranty.
3. Damaged by any major force event.
4. Situations not in “Fault Table.”
5. Situations caused by misuse.

Fault – Table

LCD display abnormality
Sensors do not work
Button failure

Hazardous Substances Containing Table

This table is prepared in accordance with the provisions of SJ/T 11364
0 : Indicates that said hazardous substance contained in all of the homogeneous   1114 materials for this part is below the limit requirement of GBP 26572.
X.  Indicates that said hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement of GBZT 26572.

Please visit http://www.imictek.com for more information.
Please contact service@imictek.com for after- sale service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>