Godox LEDP260C Bi Color LED Light Panel Instruction Manual

Godox LEDP260C Bi Color LED Light Panel

GODOX Photo Equipment Co., Ltd.

Add: Building 2, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao’an District, Shenzhen, China
Tel: +86-755-29609320(8062)
Fax: +86-755-25723423
E-mail: godox@godox.com

Foreword
Thank you for purchasing this Godox Product!
This LEDP260C video light (color temperature 3300K~5600K) is excellent for macrophotography, product shooting, photojournalistic and video recording, etc.
The LED Light provides high brightness, a wide spectrum, soft light and accurate color temperature.

Features

• 256-LED-bulbs panel is lithium-ion or DC powered
• Wireless 433MHz grouping system (6 groups & 16 channels)
• Wirelessly adjust brightness or color temperature
• Include a remote control, a detachable handle and AC adapter
• Large-sized LCD panel. Settings auto saved
• Fits almost any occasions

For your safety

• Do not place in high temperature or high humidity conditions.
• If this product overheats, it will cease operation and resume working after cooling down. This is due to the built-in overtemperature protection.
• Do not handle with wet hands, immerse in water, or expose to rain.
• Observe precautions when handling batteries:
  • Do not mix new and used batteries or batteries of different types.
  • Do not put batteries into a fire or apply direct heat to it.
  • Batteries are prone to leakage when fully discharged. To avoid damage to the product, be sure to remove batteries out when the product will not be used for a long time or when batteries run out of charge.
  • Should liquid from batteries come into contact with skin or clothing, rinse immediately with fresh water.

Parts

What’s in the Box of LEDP260C?

Power Management

1. Power Supply
   Two power supply modes are available:

   • Using lithium battery: Put two SONY NP-F970 model lithium batteries (purchased separately) into the battery compartment separately.
   • Using DC power jack: This light can be powered by DC power supply. Use a 13~16.8V adapter (included) to connect the light with the DC power jack.
     Note: When using lithium battery, the Battery Level Indicator is displayed on the LCD panel. When the indicator blinks, the lithium battery power is low. Please recharge it immediately before usage in order to avoid forceful auto off.

2. Installing Lithium Battery

   • Turn the Power Switch off.
   • Target the socket of the lithium battery towards the “+” “-” contacts of the Battery Compartment. Push the battery in until it locks.
   • Power the light on.
   • After using the light, please power it off.

Using the Video Light

1. By the Handle
   • Install the Detachable Handle into the Handle Install Groove.
2. On the Light Stand
   • Screw the Light Stand Locking Ring to the highest point and install the video light.
   • Tighten the Light Stand Locking Ring.

Operation

1. Before Usage

   • Insert the lithium battery or connect the light with the DC power supply.
   • Switch the power on, the video light giving out light.
   • Press the STOP/RUN Button to light up and shut down the LED lights.
   • LCD panel shows the information.

2. Light Brightness/Color Temperature Adjustment
   Adjusting Light Brightness

   • Turn the select dial to adjust the light brightness.
     Model| Temperature| Light Brightness Range
     ---|---|---
     LEDP260C| 3300K~5600K ±300K| 10%~100%

Adjusting Color Temperature

  * Press the SET button once and the color temperature icon blinks.
  * Turn the select dial to adjust color temperature.  

3. Wireless Remote Control
   • With 433 MHz wireless system, this product has remote grouping and control function. Up to 6 groups of LED light can be controlled. 16 channels are available with strong anti-interference capability.

Please set the channels and groups of LED video light to the same as those of remote control before usage.

Adjusting Channel/Group of the LED Video Light

• Press the CH/GR button and the group icon blinks. Turn the select dial to choose a group ID (A to F).
• Press the CH/GR button twice and the channel icon blinks. Turn the select dial to choose a channel ID (1 to 16).

Note: The wireless signal can be received only when the LED light is power on.

Technical Data

2050 (0.5 m/3300K)
2200 (0.5 m/5600K)
Color Rendering Index| >95
TLCI| ≥94
Light Brightness Range| 3300K~5600K: 10%~100%
LED Beads Quantity| 5600K: 128
3300K: 128
Operation Temperature| -10~40°C
Dimension| 360mm240mm27mm
Net Weight| 917g

Product design and specifications are subject to change without notice.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warranty

Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safe keep it.  Thank you!

Address
Seller Information| Name
Contact Number
Address
Date of Sale
Note: This form shall be sealed by the seller.

Applicable Products
The document applies to the products listed on the Product Maintenance information (see below for further information). Other products or accessories (e.g. promotional items, giveaways and additional accessories attached,etc.) are not included in this warranty scope.

Warranty Period
The warranty period of products and accessories is implemented according to the relevant Product Maintenancelnformation. The warranty period is calculated from the day(purchase date) when the product is bought for the first time,And the purchase date is considered as the date registered on the warranty card when buying the product.

How to Get the Maintenance Service
If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid wananty card. If you cannot provide valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.

Inapplicable Cases
The guarantee and service offered by this document are not applicable in the following cases: 1. The product or accessory has expired its warranty period; 2. Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, etc; 3. Breakage or damage caused by non- authorized institution or staff in the process of installation, maintenance, alternation, addition and detachment; 4. The original identifying information of product or accessory is modified, alternated, or removed; 5. No valid warranty card; 6. Breakage or damage caused by using illegally authorized, nonstandard or non-public released software; 7. Breakage or damage caused by force majeure or accident; 8. Breakage or damage that could not be attributed to the product itself. Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion and consumption are not the breakage within the maintenance scope.

Maintenance and Service Support Information
The warranty period and service types of products are implemented according to the following Product Maintenance Information:

Product Type| Name| Maintenance Period(month)| Warranty Service Type
---|---|---|---
Parts| Circuit Board| 12| Customer sends the  product  to designated site
Battery| 3| Customer sends the   product   to designated site
Electrical parts e.g.battery charger, power cord, sync cable, etc.| 12| Customer sends the   product   to designated site
Other Items| Flash tube, modeling lamp, lamp body, lamp cover,l ockingdevice, package, etc.| No| Without warranty

Godox After-sale Service Call 0755-29609320-8062

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>