WILLIAMS SONOMA Chain Link Sconce Kit Installation Guide

Williams-Sonoma Inc.
Pottery Barn – Pottery Barn Teen – Pottery Barn Kids – Williams Sonoma Home – West Elm – Rejuvenation – Mark and Graham

Assembly Instructions

CHAIN LINK SCONCE KIT

• Do not dispose of off any packaging or content of the shipping carton until assembly is completed to avoid accidentally discarding
  small parts or hardware.

• For your safety, it is strongly recommended that two people install the lighting fixture.

• This fixture has been rated for up to one (1) 60 Watt Maximum TYPE ‘A’ standard incandescent light bulb (not included) or one
  (1) 13-Watt Compact Fluorescent light bulb (not included) Or one (1) 9-Watt LED lighting bulb (Included). To avoid the risk of fire, do not exceed the recommended wattage.

• Use with approved Williams Sonoma shades only, having a minimum opening diameter of 4-0 inches and a minimum
  lamp-to-shade spacing of 3-1/2 inches.

• “ This lighting fixture is intended for indoor or protected/covered outdoor areas. Do not expose to direct rainfall.
  SUITABLE FOR EITHER DRY OR DAMP LOCATIONS”

• Save these instructions.

WARNING:

•   To reduce the risk of fire, electrical shock, or personal injury, always turn off light fixture and allow it to cool prior to replacing the light bulb.
• Do not touch the bulb when fixture is turned on. Do not look directly at the lit bulb.
• Keep flammable materials away from lit bulbs.
• Wash hands after installing, handling, cleaning, or otherwise touching this light fixture.

Pre-assembly:

• Remove all parts and hardware from the box along with any plastic protective packaging.
• Do not discard any contents until after assembly is complete to avoid accidentally discarding small parts or hardware.
• For your safety and convenience, assembly by two people is recommended.

Care Instructions:

• Dust often using a clean, soft, dry, and lint-free cloth.
• Blot spills and wipes with a clean, damp cloth immediately.
• We do not recommend the use of chemical cleaners, abrasives, or furniture polish on our lacquered finish.
• Hardware may loosen over time. Periodically check to make sure all connections are tight. Re-tighten if necessary.

TOOLS REQUIRED (not included) : Step Ladder, Philips Head & Flat Blade crew drivers, Wire Cutter / Stripper & Electrical

Parts Included:
(B) Green Ground Screw (1)
(D) Mounting Plate (1)
(E) Side Screws (2)
(F) Canopy (1)
(G) Metal Tubes
(H) Shade (1)
(I) Socket (1)

Hardware Enclosed:
(A) Plastic Wire Connectors (3)
(C) Mounting Screws (2) (includes (1) extra)

Assembly & Installation Instructions:

1. SHUT OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER!
2. Carefully unpack all fixture parts and hardware and lay them out on a clear workspace.

1. Tighten the canopy with a threaded pipe by providing double hex-nut, insert the canopy screws (C) into the mounting plate (D).

Connect the NEUTRAL FIXTURE WIRE to the NEUTRAL JUNCTION BOX WIRE (usually white insulation). Fasten each together with a Plastic Wire Nut Connector (A) by twisting the connector in a clockwise direction and wrapping the connection with electrical tape. Be sure that no wire strands are exposed.

To Make the Wire Connections:

1. Gently pull the existing wire down from the ceiling junction box and allow wires to hang. The or LIVE wire is usually black. The NEUTRAL wire is usually white. Check to see if there is a ground wire that is usually green or green with a yellow stripe or exposed copper metal wire. If needed, use a pair of wire strippers to remove about 1/2 inch of insulation from each wire.
2. Carefully inspect the fixtures wires. The NEUTRAL FIXTURE WIRE IS WHITE. The HOT FIXTURE WIRE is BLACK and the GREEN WIRE is the GROUND WIRE. If you have any doubt cannot identify the power-supply wires with confidence, then we recommend that you ask an electrician and that you not continue with the installation.
3. With the help of another person to hold the weight of the fixture, attach the fixture wires to the junction box wires as shown in the illustrations.

Connect the GROUND FIXTURE WIRE to the GROUND J-BOX WIRE using the Plastic Wire Nut Connector (A) and wrap the connection with electrical tape. Be sure that no wire stands are exposed.
If the junction box DOES NOT have a GROUND WIRE, wrap the fixture’s green ground wire around the Green Ground Screw(B) and insert the screw into the Mounting Plate (D), marked as “GND”, and tighten the screw to secure the wire.
Connect the NEUTRAL FIXTURE WIRE to the NEUTRAL J-BOX WIRE first and then connect the HOT FIXTURE WIRE to the HOT J-BOX WIRE using the Plastic Wire Nut Connectors (A). Wrap these connections with electrical tape. Be sure that no wire strands are exposed.

NOTE:
IT IS IMPERATIVE THAT THE JUNCTION BOX IN YOUR HOME BE PROPERLY GROUNDED!
DO NOT REVERSE THE NOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
Check the wiring connections and if all looks good, gently tuck the wire connections neatly into the ceiling junction box.

Williams-Sonoma Inc.
Pottery Barn – Pottery Barn Teen – Pottery Barn Kids – Williams Sonoma Home – West Elm – Rejuvenation – Mark and Graham

Documents / Resources

| WILLIAMS SONOMA Chain Link Sconce Kit [pdf] Installation Guide
Chain Link Sconce Kit
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>