MEDIC ASSIST PMS-SL-1550-52-FRx SmartLink FRx – AED Remote Monitor User Manual
- June 6, 2024
- MEDIC ASSIST
Table of Contents
MEDIC ASSIST PMS-SL-1550-52-FRx SmartLink FRx – AED Remote Monitor
PACKAGE CONTENTS
Check the contents of the SmartLink box to be sure it contains:
- SmartLink Remote Monitoring unit with installed battery pack and SD/ SIM card (or SIM Chip)
- Sensor-Cradle connected to SmartLink
- User Manual
- Quick Setup Guide
- Spare Pads Pouch
Edition 1
Publication date: December 2021
Device manufacturer: medic assist GmbH & Co. KG, Friederikastrasse 148, 44789
Bochum, Germany, support@medicassist.eu,
www.medicassist.eu
Please contact your local Philips representative for information on revision
of this document.
It is important to understand how to use your SmartLink safely.
Please read these warnings and precautions carefully.
A warning describes something that could cause serious personal injury or
death. A precaution describes something that could cause minor personal
injury, damage to the SmartLink, loss of data stored in the SmartLink, or less
chance of successful remote checking of the defibrillator including data
transfer.
WARNINGS
Any visible damage or disassembly of SmartLink may cause harm and result in
the loss of type approval, functionality and warranty. Do not use SmartLink if
the environmental conditions do not meet its specified temperature and
humidity range as described hereinafter. Do not remove the SIM-Card or SD-RAM-
Card (hidden mounted within the battery compartment). These parts are not user
serviceable and the SmartLink will not be able to work with any other SIM or
memory card. AutoSend periodic self-test feature must be “On” (default setting
on the AED) for proper function. AED needs to be placed on the cradle as shown
in the Quick Setup Guide, so that the Infrared receiver of the cradle is
aligned to the Infrared port of the AED.
Flammable Gas Do not use the SmartLink in the presence of flammable gases
such as in an oxygen tent. Move supplemental oxygen and oxygen delivery
devices and other flammable gases away from the SmartLink.
Battery The SmartLink battery is not rechargeable. Do not try to
recharge, open, crush, or burn the battery,
or it may explode or catch fire.
Fluids Do not let fluids get into the SmartLink. Avoid spilling any
fluids on the SmartLink or its accessories. Spilling fluids into the SmartLink
may damage it or cause a fire. Do not sterilize the SmartLink or its
accessories.
Accessories Using damaged or expired equipment/ accessories or non-
approved accessories may cause the SmartLink to perform improperly, and/or
injure the user.
Interference Do not use SmartLink within 10 inches of another medical
appliance (except AED). Avoid long term exposure to Smartlink due to RF
radiation exposure.
Children Keep SmartLink out of reach of children to avoid the potential
risk of inhalation or swallowing of small parts or strangulation by sensor
cable.
Sensor Cable Be cautious when closing the AED case, so that the sensor
cable does not get pinched. Pinched sensor cable may impact remote monitor
functionality.
PRECAUTIONS
Device Handling The SmartLink was designed to be sturdy and reliable for
many different use conditions. However, handling the SmartLink too roughly can
damage it or its accessories and will invalidate the warranty coverage. Check
the SmartLink and accessories regularly for damage, according to directions.
Your SmartLink version may only be used for fixed installations and shall not
be moved without need – this may result in delay in messaging and higher
drainage of the battery.
Maintenance Improper maintenance may damage the SmartLink or cause it to
function improperly. Maintain the SmartLink according to guidance provided in
the User Manual.
Mobile Connectivity Never replace existing emergency call or other safety
or wired communication devices by SmartLink. Due to its mobile network
dependency SmartLink should only act as an additional emergency device.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more
of the following measures: — Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver. — Connect the
equipment into an outlet on a circuit different from that
to which the receiver is connected. — Consult the dealer or an experienced
radio/TV technician for help.
IMPORTANT NOTE
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be operated with minimum distance 20 cm between the radiator & your body.
INTRODUCTION
SmartLink is a battery-powered device intended to be used only for supervision of the Philips defibrillators (HS1, FRx) built-in self-test functionality using a special patented sensor, which needs no fixed connection to the defibrillator.
SETTING UP SMARTLINK
Setting up the SmartLink is simple and quick. The SmartLink Quick Setup Guide provides illustrated instructions for setup (Install Routine).
USAGE AND FUNCTIONALITY DESCRIPTION
SmartLink system consists of the mobile and battery powered SmartLink unit
which is stored in the AED carrying case, the cradle containing the sensors
and the remote computer based host center. This SmartLink solely monitors the
AEDs self-test function (basic functionality). Besides the basic functionality
SmartLink may offer additional functions in other versions.
Power supply SmartLink is powered by a primary LiMnO2-cell. It delivers
the processor-controlled
functionality described above. The battery is field exchangeable by the user.
Reinstalling or replacing the battery will restart the device and trigger the
Install Routine.
SmartLink is intended to not send data in a time frame of 30 minutes after any
movement was detected. Therefore the intended use case for monitoring function
is the SmartLink and AED standing still. To ensure monitoring of the AED is
not delayed, SmartLink should remain stationary when the AED is not in use.
CLEANING SMARTLINK
The outside of the SmartLink can be cleaned with a soft cloth dampened in
soapy water, chlorine bleach
(2 tablespoons per quart or liter of water), or ammonia-based cleaners with up
to 10% ammonia by volume or by weight. Caution: Do not use isopropyl (rubbing)
alcohol, strong solvents such as acetone or acetone-based cleaners, abrasive
materials, or enzymatic cleaners to clean SmartLink. Do not immerse the
SmartLink in fluids or allow fluids to spill onto it. Do not sterilize the
SmartLink or its accessories.
TECHNICAL DATA
- Module Dimensions 213 x 118 x 27 mm
- Weight (Module w/o battery) 205 g
- Sensor-Inlay passive featuring IR and inductive receiver with cable connection to Module
- Storage temperature range -20 – 60°C
- Operating temperature range 0 – 50°C
- Humidity range 0% – 95% rel. humidity, non condensing
- SIM built-in 3V SIM-Card
- Battery supply 3V LiMnO2, 4 x 1,5Ah
- Battery Weight 140 g (4 cells)
- Battery dimensions 82 x 24 x 110 mm
- LTE Module BG95 Quectel, Cat M1, Cat NB2 (FCC, GCF, PTCRB, IC and others), FCC ID: XMR201910BG95M3
- Certifications USA: FCC part15b, PTCRB FCC ID: 2A2C5-SL-MA-1550-5X PMS-SL-1550-52-FRx is hardware identical to MA-1550-25 FRx
The SmartLink is located directly adjacent to the defibrillator in the
carrying case.
The SmartLink device has no user interface.
Declaration of conformity We, medic assist GmbH & Co. KG,
Friederikastrasse 148, 44789 Bochum, hereby declare that this product conforms
with the basic requirements and the other relevant regulations of the named
certifications above.
Please contact your local Philips representative for information on revision
of this document.
ENVIRONMENTAL CONSIDERATIONS
The battery cells contain chemicals. The chemistry used in each battery is
identified by a symbol on the label. You should be informed about your local
laws and legal requirements regarding disposal of batteries. In case of any
questions please refer to your local authorities. Recycle the battery at an
appropriate recycling facility.
Reproductions of any kind, completely or in part and in particular photocopy
or digital copies, as well as translations are permitted only with the written
consent of the copyright holder. This manual complies with the technical state
at the date stated on the title page. In the context of technical changes,
such as improvement or further development, changes may occur at any time.
Actual product characteristics may also differ from the behavior described in
this document, for example due to remotely installed updates.
The trademarks, logos, and product names are trademarks of their respective
owners.
© 2021 Philips & medic assist All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>