ironcat FM13DM Infinity G Pro Dual mode Wireless Gaming Mouse Instructions
- June 6, 2024
- ironcat
Table of Contents
INFINITY G PRO
Dual mode wireless gaming mouse
Function layout
| 1. Left click | 6. DPI | 11. Polling rate:1000Hz |
|---|---|---|
| 2. Right click | 7. Scroll up | 12. RGB OFF |
| 3. Middle click | 8. Scroll down | 13. RGB ON |
| 4. Forward | 9. Polling rate:125Hz | 14. Power Off |
| 5. Backward | 10. Polling rate:500Hz | 15. Type-c connection |
Instruction
Mouse instruction:
- Take out the wireless USB Nano receiver from package
- Plug the receiver into your computer USB port
- Turn on the mouse power by switching the power switch on the bottom of the mouse
- Waiting for computer installation finished
DPI setting and indication:
- DPI level: 400-800-1600-2400-3200-6400,total 6 levels DPI
- By pressing the DPI button on the top of mouse to change DPI circularly
- The mouse wheel led color will indicate the DPI level as below: 400DPI: Red color breath. 800DPI(default):blue color breath.1600DPI: green color breath. 2400DPI: Yellow color breath.3200DPI: Cyan color breath. 6400DPI: Purple color breath
Note:
- DPI can be set by software , MAX DPI is 19000dpi
- DPI led effects can be set by software and can turn off the DPI led to save power
Polling rate:
125-500-1000Hz can be set by software, default polling rate is 1000Hz
Power switch function:
- Switch at RGB off place: turn on the mouse power, but RGB led is off
- Switch at power off place: turn off the mouse power
- Switch at RGB On place: turn on the mouse power and RGB led
Wired and wireless function:
- Wired and wireless mode switch automatically, when you plug the receiver into computer without cable connection, it will work as wireless mode.
- If you connect the cable from computer to the mouse, it will switch to wired mode automatically and work as wired mode.
Low power and charging indication
- Low power indication: when mouse battery power is low, the Red color in the wheel will flash, so you need charge when the Red color flash in the wheel
- During charging the yellow color led in the wheel will flash, after the battery charging full, the LED color will back to DPI indication and charging stop automatically,
Pairing
- use pairing tool to pair the receiver and mouse if you need change to new receiver or miss connection
Note: If you need customize function, pls download the software from website
CAUTION
- Keep the battery dry.
- Avoid locating the battery terminals near metallic object.
- Do not short-circuit and avoid metallic or water come into mouse to cause battery short
- Use computer USB and specified cable to charge the mouse
Main Specification
| Size: | 125×63.5x40mm |
|---|---|
| Weight: | 76±2g |
| Switch | As per order spec. |
| Sensor | PAW3370 |
| Max DPI | 19000 |
| Default DPI: |
400-800-1600-2400-3200-6400DP1
IPS| 400ips
Acceleration| 50g(Max)
LOD| 1mm and 2mm
Polling rate| 125-500-1000Hz
Interface| USB 2.0
Battery type| Li-ion Polymer Battery
Battery capacity| 500mAh
Charging time| Around 2. 5h
FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>