CRAZVIEW JQ901A Projector User Manual

PROVIDE YOU WITH A NEW VISION

Model No : JQ901A

User Manual

ADDITIONAL WARNINGS AND PRECAUTIONS

1. Do not look directly into the projector light.
2. Don’t touch the projector lens.
3. Mains adapter is used as a disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely.
4. Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure.
5. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the
6. Use of this unit near fluorescent lighting may cause interference regarding the use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause.
7. Shock hazard – Do Not Open.
8. Caution and marking information is located at the rear or bottom of the
9. To reduce the risk of fire or electric shock, do not expose this apparatus to rain, moisture, dripping, or splashing.
10. Objects filled with liquids, such as vases, shall not be placed on the

PRODUCT OVERVIEW

1. POWER Button
2. RETURN Button
3. NAVIGATION
4. MENU Button
5. SOURCE S ” Button
6. Keystone Correction
7. Focusing Ring
8. LENS
9. Headphone Jack
10. AV

| 11. Micro SD Card

12. HDMI Port 1

13. HDMI Port 2

14. USB Port

15. POWER INPUT

16. Adjusting Knob

17. POWER on Indicator

18. IR Window (Front side )

19. IR window (Rear side)

---|---

CONTROL

Install Power Adapter

As shown in Picture **1**connect the projector and the power source with the included AC Power cable.

CONTROLS OF REMOTE

Install / Remove Battery Of Remote

Remove the battery compartment cover on the back of your remote by carefully sliding it open. The battery cover can then be lifted away. Fit the correct batteries (2 X AAA batteries not included), referring to the polarity markings. Finally, replace the cover.

NOTES:

• Batteries shall not be exposed to excessive heat such as sunshine, fire
• Be sure that the batteries are installed polarity correctly.
• Only same or equivalent type batteries as recommended are to be used.
• Do not dispose of batteries in fire, the battery may explode or leak. Do not try to recharge a battery
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-me, etc) batteries

TO REDUCE IMAGE DISTORTION

It is recommended to move the projector as close to the center of the screen.

PLACING YOUR PROJECTOR ON THE CEILING

When installing the projector in the ceiling, please purchase a projector mount recommended by an installation professional and follow the instructions that come with the mount.

Before installing the projector in the ceiling, please check to make sure the ceiling structure can support the weight of the projector and the mount. If in doubt, please ask the advice from an installation professorial.

NOTE: Projector mount and screw(s) not included

ADJUST THE VERTICAL LOCATION

Follow the below picture to adjust the vertical location.

TO REDUCE IMAGE DISTORTION

It is recommended to move the projector as close to the center of the screen.

Adjust the focus by turning the knob while observing the image pixels near the center of the screen. Optimal focus is obtained when the pixels are clearly visible. Depending on the projected screen size, the focus near the screen edges may be less sharp than the screen center.

keystone image is created when the projector beam is projected to the screen at an angle. Keystone correction will restore the distorted image to a rectangular or square shape.

CONNECTION

Wired Screen Mirroring Connection

CONNECT AN IPHONE/PAD

1. Press the signal source key “s” of the projector or the remote control and select “Miracast”. Then select IOS Miracast.
2. Plug an original USB charging cable into the USB port of this projector.
3. Please select “Trust this device” when the iPhone asks “Trust”or “Don’t trust”, and enter the Your iPhone password to connect.

Wireless Screen Mirroring Connection – Connection Method 1

WIRELESS WIFI CONNECTION-WIFI TRANSFER CONNECT AN IPHONE/IPAD

1. Press the key “s” of the projector or the [source] button on the remote control and select”Miracast”.
2. Select Setting, click wifi setting, select your home wireless network in the projector display interface, enter the password. ( or long-press “menu” button on the remote control or on the project to set wifi )
3. Open the phone WiFi settings, connect to your home wireless network. Make sure the projector and phone are connected to the same WiFi.
4. Come back to IOS Miracast. Slide the phone interface from the bottom up to enter the control central(Full-screen phones slide down from above,-those with home button slide up from below), then open “Screen Mirror­ing”.Then search and select the projector device,(Note: the name of the projector device is Dualcast-**”), click to connect.

CONNECT AN ANDROID PHONE/TABLET

1. Press the key “s” of the projector or the [source] button on the remote control and select”Miracast”.
2. Select Setting, click wifi setting, select your home wireless network in the projector display interface, enter the password. ( or long-press the “menu” button on the remote control or on the project to set wifi )
3. Come back to Android Miracast. Since different brands of Android phones have different settings, find the screen share and connect the projector, Samsung phones find”Smart View”, other phones find “Multi-screen” or “Wireless projection”, Then Search and select the projector device (Note: The name of the projector device is Dualcast-‘), click to connect.

Wireless Screen Mirroring Connection – Connection Method 2

CONNECT AN IPHONE/IPAD
Requires Cellular DataTraffic Transfer

1.  Press the signal source key “s” of the projector or the remote control and select”Miracast”. Then select IOS Miracast.
2. Open the wifi in the Phone settings, search and select projector hotspot Dual-cast-***, enter password to connect(Note: The hotspot name is on the projector screen “SSID: Dualcast-‘”, the password is “PSK:”12345678”).
3. Slide the phone interface from the bottom up to enter the control center. (Full-screen phones slide down from above, those with home button slide up from below), then open “Screen Mirroring “.Then Search and select the projector device(Note: The name of the projector device is Dualcast-***), click to connect.

CONNECT AN ANDROID PHONE/TABLET

1. Press the signal source key “s” of the projector or the remote control and select”Miracast”.Then select Android Miracast.
2. Since different brands of Android phones have different settings, find the screen share and connect the projector. Samsung phones find “Smart View”, Huawei phones find”Multi-screen”.Then Search and select the projector device (Note: The name of the projector device is Dualcast-***), click to connect.

CONNECT A WINDOWS DEVICE

1. Press the signal source key “s” of the projector or the remote control and select”Miracast”.Then select Windows Miracast
2. Open the windows device settings interface and find the “Connections” icon.
3. Search and select the projector device: Dualcast-**- and click Connect.”

More Tips about Netflix. Prime Video, Hulu, etc

It works with youtube, chrome, safari, facetime when you connect it to a smartphone directly.

And it doesn’t support play-protected video when you connect it to your smartphone directly. (Netflix, Prime Video, Hulu, etc) Due to this video having an encryption protocol, the projector has no right to recognize when it is connected directly to the phone via the USB interface.

But it works with Netflix, amazon prime video, or any other copyright videos when connecting this projector to a laptop, fire tv stick, Roku, or Chrome cast. The reason why the fire stick or other HDMI device can play Netflix is that the HDMI interface encryption protocol includes Netflix’s.

Connect HDMI Show The Image On Projector Screen

Follow the below picture to connect the HDMI cable and device.

1. Turn off the unit before connecting the HDMI cable.

2. After connecting, press the button to turn on the unit, and the power indicator will light GREEN

3. Press the S ” / SOURCE button to HDMI mode and the video of the HDMI device will show on the projector screen. There are 2 HDMI inputs, the HDMI1 interface corresponds to HDMI 1 in SOURCE mode , and the HDMI2 interface corresponds to HDMI 2 in SOURCE mode.

4. Press the button to turn off unit power.

HDMI HD Signal Input: This Interface Can Be Input With HD Player HDMI Output At The Connection

Connect AV Show The Image On Projector Screen

Follow the below picture to connect the AV cable and device.

1. Turn off the unit before connecting the AV cable.
2. Use AV cable to connect follow below figure
3. After connecting, press the button to turn on the unit and the power indicator will light GREEN
4. Press the”S”/ SOURCE button to AV mode and the video of the AV device will show on the projector screen
5. Press the buttons to turn off unit power.

Connect Audio Output (Aux Out / Line Out / Earphones)

Follow the below picture to connect the audio cable and device.

1. Press the buttons to turn off the power of your projector before the connection.
2. Use an audio cable to connect follow the below figure.
3. After connecting and turning on both units. Your projector sound from an external device now.
4. After using, turn off both units.

Install USB Device And Micro SD Card

Follow the below picture to install the USB and microSD Card. Turn off the unit before installing the USB / microSD Card.

Install USB / Micro SD device:

1. Turn off the unit before installing a USB / microSD Card.

2. Install the USB device into the USB port.

3. After connecting, press the button to turn on the unit and the power indicator light GREEN

4. Press the “S” / SOURCE button to enter and use buttons to search the MEDIAPLAYER mode.

5. After selection, use buttons to search the MUSIC / PHOTO / MOVIE icon and press the button to enter. If necessary, use the button to select microSD card or USB and press the ‘ button to enter.

6. Use buttons to search the correct file and press the button to preview the playback file and press the button of the unit or button of the remote to start playback.

7. Press the button to fast search forward and rewind.

8. Press the button to search the next or previous file.

9. During playback, press the button to pause and press again to resume.

NOTE: Remove USB / microSD device, press the button to turn power FIRST.

USING BLUETOOTH PLAYBACK

Pairing to Bluetooth Wireless Speakers or Sound Bar

NOTE: Bluetooth is OFF by default when the projector powers ON. Bluetooth can be turned ON or OFF from the OPTIONS Menu.

1.  Enable Bluetooth on the receiver (external speakers, soundbar, etc.) to which you wish to connect. Devices such as smartphones, tablets, or computers are not Bluetooth receivers and will not connect to the projector. To eliminate confusion, you should disable Bluetooth on all receivers to which you do not wish to connect.
   The Bluetooth pairing list is not acceptable, it needs to show what is the step to turn on the projector and show the picture in the manual.

2. Power on the projector and make sure the projector’s Bluetooth is on and in pairing mode (see the note above). Press the menu key from the remote>>>select OPTION>>>select BlueTooth>>>press the navigation >1< to turn on the bluetooth>>>Select the Bluetooth on, press the OK key from the remote, when the Scan shows on the screen, press the OK key again>>>When the screen shows ‘Searching, >>>the Bluetooth devices name will be shown on the screen, select it and press the OK key to connect it.

3. When successfully paired, it will show ‘ Bluetooth Connected’ on the menu. Exit the menu, the sound will come out from the Bluetooth speaker.

4. It can connect the last Bluetooth speaker automatically when the unit is powered on again. Note: It needs power on the last connected Bluetooth speaker first, then turned on the projector. if it can’t connect the last devices automatically, please repeat steps 2-3.

After the initial pairing, the projector and the Bluetooth speakers will stay paired unless unpaired manually by the user, or erased due to a reset of either device. If this occurs, or you find either unit is unable to connect, repeat the above steps.

@CRAZVIEW
1-888-965-5888
US: service@crazviewtec.com
UK: service.uk@crazviewtec.com
EU: service.eu@crazviewtec.com
JP: service.jp@crazviewtec.com
www.crazviewtec.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>