BUTTONS ONBTN10 Wireless Earbuds User Guide
- June 6, 2024
- BUTTONS
Table of Contents
BUTTONS ONBTN10 Wireless Earbuds User Guide
Powering Up And Pairing
-
When taking your earphones out of the charging case, the earphones issue a voice prompt of “Ready for pairing”. This means your earphones have entered pairing mode;
-
Turn on your mobile’s Bluetooth, find “BUTTONS ON” in the Bluetooth device list and click “Connect”;
Available equipment -
The system pops up the “Authorization Bluetooth Pairing Request” dialog box, press the “Pair” button, and the earphones voice prompts “Connected”, indicating that the earphones are successfully connected. Note: After the first-time connection, the earphones will automatically connect to the last connected device the next time; The earphones can also be used separately when next connection. Please charge the charging case and earphones before first use.
Pair a new device
Put your earphones into the charging case, and keep the charging case lid opened. Press and hold the pair button in bottom for 3 seconds until the red and white LED blinking. Then take out earphones;
Your earphones will automatically enter pairing mode, and you may pair with a device using the steps described in the “Paring section.
Note: the pair button may not work when charging box battery low (red LED light up when open the cover). In this case please turn off phone Bluetooth if it connect already or wait for re-connection time out to enter pairing mode.
ANC Mode Switch
After connecting and wearing both earphones, tap the X1 C’J touch panel on the left earphone to switch between ANC PI / ambient sound / standard modes.
- Enter ANC Mode: Can hear voice prompt “ANC On”;
- Enter Ambient Sound Mode: Can hear voice prompt “Ambient On”;
- Enter Standard Mode: Can hear voice prompt “Off”;
Note: The default mode of the earphones is ANC mode; Mode switch cannot be performed when only one earphone is used.
Wearing Detection & Sleep Mode
Wearing Detection:
While music is played, the music will automatically paused when you take off either one or both earphones and will resume when you put on the earphone(s) again.
During a phone call, the telephone receiver will be enabled when you takeoff both earphones, and the earphone speakers will be enabled when you put on either or both earphones.
Note: Touch control is not supported if your earphones are detected not be worn.
Voice Assistant
To enable the voice assistant, tap the touch panel on either earphone for three times
Music Control
Play/Pause
- Using both earphones: Tap the touch panel on the right-side earphone one time to pause & play music
- Using one earphone: Tap the touch panel on the earphone one time to pause & play music
Track Switch
- Previous: Double-tap the touch panel on the left earphone
- Next: Double-tap the touch panel on the right earphone
Volume Control
- Volume Up: Press and hold the touch panel on the right earphone for is
- Volume Down: Press and hold the touch panel on the left earphone for is
Note: The system will issue two beeps when the volume is adjusted to the maximum or minimum.
Call Control
Answer Calls
- Using both earphones: Tap the touch panel on the right earphone one time to answer a call
- Using one earphone: Tap the touch panel on the earphone one time to answer a call
Reject Calls
- To reject a call, double-tap the touch panel on either earphone
End Calls
- To end a call, tap the touch panel on right earphone during the call
Call Volume Control
- Volume Up: Press and hold the touch panel on the right earphone for is
- Volume Down: Press and hold the touch panel on the left earphone for is
Charge
Charge earphones :
Put your earphones into the charging case and ensure the two metal contact points are well contacted, the charging box will automatically charge the earphones.
- Earphone Low Battery: Voice prompt “Battery Low”
- Charging: LED indicator on charging case turns white and flash slowly
- Charging Done: LED indicator on charging case turns off
Charge the charging case
Use provided charging cable connect charging box and charger together to charge earhpones and charging box.
- Charging: LED indicators on the charging case turn white and flash;
- Charge complete: LED indicators on the charging case are off;
- Charge Fault: LED indicators on the charging case turn red and rapidly flash;
Note: The above light indication only applies to charge the charging case separately; When the charging case cover is opened, if the LED indicator is red, it means that the charging box is low battery; Please use standard 5V=1A charger for this product, as those chargers out of specification may damage the device.
Safety Guide
Warning: Electrical and electronic equipment, parts and batteries marked with this symbol must not be disposed together with normal household waste. They must be collected and disposed separately to protect the environment. Your BUTTONS retailer will advise you of the correct method of disposal in your country/region.
Warning: Prolonged listening at high volume levels can cause hearing
damage.
Warning: Choking Hazard – small parts.
Warning: This product contains magnets
Manufacturer: Buttons (Shanghai) Technology Limited
Name: BUTTONS ON
Model: ONBTN10
Charging voltage/current: 5V IA
Do not use your earphones during charging
Items in package:
- Silicon eartips x4
- USB Type A to Type C
- charging cable x1
- earphones x2
- charging case xl
- Quick Start Guide x1
Specifications
- Frequency: 20 ^ 20KHz
- Resistance: 240hm
- Sensitivity: 113d13±3dB Speakers: 10mm biofibre+ AU composite element
- Noise reduction: up to 35dB (200Hr1000Hz)
- ANC Mic: Analog Mic (x2), -36 — -40dB@1kHz Digital Mic (x2),-26 +1-1 dBFS at 94dB SPL@lkHz
- Call Mic: Digital Mic. -26 +/-1 dBFS at 94dB SPL@1kHz
- Battery life: 8h (noise cancellation enabled and medium sound volume) 10h (noise cancellation disabled and medium sound volume)
- Earphone Battery: DC 3.7V 0.32Wh
- Battery of charging case: DC 3.8V 1.67Wh
- Bluetooth version: v5.1
- Bluetooth range: Over 12meters
- Weight: About 6.8 g (each earphone) About 54g (charging case)
- Warranty period: 1 year
FCC Statement
CCI EU WARNING: Hereby Buttons declares that the radio equipment type
(BUTTONS ON is in compiance with Directiw 2014/53/EU.11* device may be
operated ‘pall member states of the EU. TVs device complies virth part15d the
FCC Rules.
Operation b subject to the following two conditions: (1)This device Femay not
cause harmful interference, and (21 this device must accept any interference
received, inducing interference that may cause undesired oneratlon.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction. My
changes or modifications not expressly approved by the party responsible for
compliance could void the users authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits fora Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there Is no guarantee that interference will not occur In a particular installation. if this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver Is connected.
- Consult the dealer or an experienced radio/P/ technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>