TELESAIL PM4254 FTTH Home Gateway User Guide

June 6, 2024
TELESAIL

TELESAIL PM4254 FTTH Home Gateway

Overview

PM4254 GPON ONT is a FTTH gat eway,for sm all and m edium – sized businesses, SOHO office and hom e users, int egrat ing GPON, WI FI . This series of product s com plies wit h t he G.988 int ernat ional st andard and has good int eroperabilit y and operabilit y, enabling int eroperabilit y wit h m ainst ream m anufact urers’ OLT devices.

Main Specifications

ITEM

| UNIT|

SPEC

---|---|---

OPTICAL

|

Working wavelength

| nm| TX1310,RX1490
TX POWER| dBm|

1-4(GPON)

RX Sensitivity

| dBm| ≥ -28
optic connector| /|

SC/APC

OTHER

|

WIFI

| /|

2.4G:802.11 b/g/n 2.4GHz 300Mbps 5G:802.11 a/an/acGHz     867Mbps

TYPE

| /| HGU
POWER| V/A|

DC12V 1.5A

Size

| mm| 19613531
Operating temperature| ℃|

-5~40

Instructions for Use

Power Connection

This m achine is support ed by t he power adapt er. First ly, connect the DC 12V output cable of the power adapter to the DC 12V port of the m achine, and then plug the external regulated power supply int o t he AC100~ 240V of t he m ains. The power indicat or on t he panel is on, indicating that the power supply is working norm ally.

INTERFACES
INTERFACES Introduction
ON/OFF Power switch button
Power Power input interface, DC 12V/1.5A
Optical GPON fiber interfaces, using SC/APC fiber access
LAN1-LAN4 LAN service interface
Reset Reset button
WLAN WIFI switch
FXS VOIP Interface
Indicators Description
Indicator Status Description
Power ON The device is powered on normally.
OFF The device is not powered on.
PON Twinkling Received light, device not registered
ON The ONU is connected to the OLT and registered successfully.
OFF No optical received, device not registered
LOS Twinkling Fiber break or optical power exceeds limit
OFF ONU accepts normal optical power
LAN1-LAN4 ON The network port is connected but no data is transmitted.
Twinkling Network port has data transmission
OFF The device is not powered on or the network port is not connected to the

terminal device.
WIFI(2.4G/5G)| ON| WIFI works fine
Twinkling| WIFI has data transmission
OFF| WIFI work abnormally
FXS1/FXS2| ON| The caller is ringing
Twinkling| Means the user is off the phone or on the phone
OFF| free

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution!

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Canada Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems

  1. the device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
  2. for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;

Mounting an ONU onto the wall

  1. Mark two positions with the same spacing as that between the two mounting holes of the ONU using a marker on a wall.
  2. Select a proper drill bit according to the outer diameter of the screws,Use a hammer drill to drill the marked positions on the wall. Then clean the holes and install two expansion bolts.
  3. Use a screwdriver to fasten the screws into the expansion bolts,reserving 13mm ends out of the wall,and mount the ONU onto the screws.

NOTE
It is recommended to use two screws with a diameter of 6mm and a length greater than 20mm.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals