Shelly-Motion Wireless Motion Sensor User Manual
- June 6, 2024
- Shelly
Table of Contents
Shelly-Motion Wireless Motion Sensor
User Manual
SHELLY MOTION WIFI SENSOR
Introduction to Shelly
Shelly® is a family of innovative Devices, which allow remote control of
electric appliances through mobile phone, PC or home automation system.
Shelly® Devices use WiFi connectivity, and they can be controlled from the
same network or through remote access (any internet connection). Shelly®
Devices may work standalone on the local WiFi network, without being managed
by a home automation controller, or it can also work through home automation
cloud services, accessing remotely from wherever the User has Internet
connectivity. Shelly® has an integrated web server, through which the User may
adjust, control and monitor the Device. Shelly® has two WiFi modes – access
Point (AP) and Client mode (CM). To operate in Client Mode, a WiFi router must
be located within the range of the Device. Shelly® devices can communicate
directly with other WiFi devices through HTTP protocol. An API can be provided
by the Manufacturer. Shelly® devices may be available for monitor and control
even if the User is outside the range of the local WiFi network, as long as
the WiFi router is connected to the Internet. The cloud function could be
used, which is activated through the web server of the Device or through the
settings in the Shelly Cloud mobile application. The User can register and
access Shelly Cloud, using either Android or iOS mobile applications, or any
internet browser and the web site:
https://my.shelly.cloud/
What is Shelly Motion
Shelly Motion is high sensitivity ultra-low power consuming WiFi Motion sensor
which stays connected to internet 24/7 and no additional HUB is required to
control it. Shelly Motion sends notification once motion is detected or it
will instantly turn on the lights.
It has built-in accelerometer providing protection when someone tries to
dislocate or move the device. The built-in light sensor gives additional
opportunities for home or office automation.
Shelly Motion has a built-in 6500mAh rechargeable battery which allows the sensor to be connected to the Internet (standby mode) for up to 3 years without recharging, and in active transmission (approx. 6 hours/day motion detected) estimated between 12 and 18 months.
Specification
- Working temperature -10 ÷ 50°C
- Radio protocol WiFi 802.11 b/g/n
- Frequency 2412 – 2472 MHz (max. 2483.5 MHz)
- Operational range (depending on local construction) up to 50 m outdoors or up to 30 m indoors
- Battery – 6500mAh 3,7V
Visual indications
The Motion Sensor is equipped with a LED diode, signaling sensor’s operating modes and alarms.
Button user interaction
Use pin to press the button as shown at the picture
- Short press (AP mode) – wake-up from AP sleep mode (AP is only for 3 minute and device power OFF, battery save transportation mode)
- Short press (STA MODE) – send status
- Long press 5 sec (STA mode) – AP mode
- Long press 10 sec (STA mode) – Factory reset
Installation Instructions
CAUTION! Before beginning the installation please read the accompanying
documentation carefully and completely. Failure o follow recommended
procedures could lead to malfunction, danger to your life or violation of the
law. Allterco Robotics is not responsible for any loss or damage in case of
incorrect installation or operation of this device.
CAUTION! Do not allow children to play with the device, especially with
the Power Button. Keep the devices for remote control of Shelly (mobile
phones, tablets, PCs) away from children.
How to assemble and mount the Shelly Motion.
- In your package as seen in fig. 1 you will find the body of the Shelly Motion, ball arm plate and wall plate.
- Place the ball arm plate onto the body of Shelly Motion as seen in fig. 2.
- Twist the ball arm plate in clock-wise direction as seen in fig. 3.
- Place the wall plate onto the ball arm plate – fig. 4.
- The assembled Shelly Motion sensor should look like fig. 5.
- Use the locking dowel provided in this package to mount your Shelly Motion on to the wall.
Shelly Motion area of detection
Shelly Motion has range of 8m or 25ft. Optimal height for mounting is between 2,2m/7,2ft and 2,5m/8,2ft.
CAUTION! Shelly Motion has “No detection“ area one meter in front of the
sensor – fig. 6
CAUTION! Shelly Motion has “No detection“ area one meter behind solid
objects (sofa, closet, etc.) – fig. 7 and fig. 8
CAUTION! Shelly Motion cannot detect movement through transparent
objects.
CAUTION! Direct sun light or close heating sources can trigger false
motion detection.
Declaration of conformity
Hereby, Allterco Robotics EOOD declares that the radio equipment type Shelly
Motion is in compliance with Directive 2014/53/EU, 2014/35/EU, 2014/30/EU,
2011/65/EU. The full text of the EU declaration of conformity is available at
the following internet address:
https://shelly.cloud/knowledge-base/devices/shelly-motion/
Manufacturer: Allterco Robotics EOOD
Address: Bulgaria, Sofia, 1407, 103 Cherni vrah Blvd.
Tel.: +359 2 988 7435
E-mail: support@shelly.cloud
Web: http://www.shelly.cloud
Changes in the contact data are published by the Manufacturer at the official
website of the Device
http://www.shelly.cloud
The User is obliged to stay informed for any amendments of these warranty
terms before exercising his/her rights against the Manufacturer.
All rights to trademarks She® and Shelly® , and other intellectual rights
associated with this Device belong to Allterco Robotics EOOD.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>