Micronet Union Technology WWYLT18 AC1200 Gigabit Dual Band Wi-Fi Router User Guide

User Guide
AC1200 Gigabit Dual Band Wi-Fi Router

Packing list:

1. The device
2. User guide
3. Power adapter
4. Ethernet cable
   If the above accessories are missing, please contact customer service for replacement.

Schematic Diagram of Router Connection

Wireless connection
The client-side connects to router Wi-Fi
Connect the Device The defaulted username and password are on the bottom label

Wired connection
Connect the PC and router via LAN1, LAN2 or LAN3 with a cable

Configure the Internet

2.1. Configure the Router in Bridge Mode
After the connection is completed, use a mobile phone or computer to search for the Wi-Fi name 2.4G SSID or 5G SSID on the label at the bottom of the device, enter the password, connect to the Wi-Fi, and then the Internet access is available.
2.2. Configure the Router in Gateway Mode
2.2.1. Dial-up for Internet Access：
①After the connection is completed, use a mobile phone or computer to search for the Wi-Fi name 2.4G SSID or 5G SSID on the label at the bottom of the device and enter the corresponding password to connect to Wi-Fi. Open the mobile phone or computer browser, visit the 192.168.10.1 website, enter the default username and default password on the label at the bottom of the device, and enter the router management interface.

② Enter the router management interface and select the network mode.  Change the mode to gateway mode.

③ In the router management interface, click Install-Install Settings and select PPPoE. Fill in the User Name and Password, click Save. Wait for the device to save the settings and Internet access is available. The Wi-Fi name is the default name (on the label at the bottom of the device).

2.2.2. Static IP for Internet Access
In the router management interface, click Network-Network Settings-WAN Connection, select Static IP in WAN Access Type, fill in the IP Address, Subnet Mask, Default  Gateway, and DNS1 (DNS2 and DNS3 are optional) and click Save&Apply, wait for the device to save the settings and Internet access is available. The Wi-Fi name is the default name (on the label at the bottom of the device).

2.2.3. Dynamic IP for Internet Access
The router defaults to dynamic IP (DHCP Client) for Internet access. The Wi-Fi name is the default name (on the label at the bottom of the device).
2.3. Configure the Router in Repeater Mode
① In the router management interface, select Network-Mode, change the mode to Repeater, and click Save&Apply.

② In the new router management interface, select Network—5G Settings—Network Scan, click Site Survey, select the uplink signal, click Next.

Wireless Site Survey

SSW| 13SSW| | | | |
---|---|---|---|---|---|---
CMCC-GGK b-5G| 18:42:d4:00:00:1d| 36 (A+N AC)| AP| WPA2-PSK| 92| Q
wwlh-office| cO:b5:cd:cd:69:9b| 149 (A+N AC)| AP| WPA2-PSK| 75| Q
CMCC-bc3J-5G| 00:00:1f:87:bc:30| 149 (A+11 AC)| AP| WPA2-PSK| 74| 0
VVireless_Wi-Fi5| 18:d9:8f:f0:6f:46| 36 (A +N +AC)| AP| WPA- PSKIWPA2-
PSK| 67| Q
0
Wireless| 18:d9:81:e0:61%44| 36 (A+1+AC)| AP| WPA
PSK IW1PA2-| PSK
67
wraith-office| cO:b5:cd:cd:69:95| 36 (A+M+ AC)| AP| WPA2-PSK| 67|
C MC C -xqD1-56| 00:e0:4c:81:96:c1| 44 (A 41.PAC)| AP| INPA2 PSK| 65| 0
CMCC -KA6C -5G| 00:0e:1f:83:el:ea| 44 (A+N+AC)| AP| WPA2-PSK| 63|

③ Fill in the Pre-Shared Key and click Connect.

Revise Wi-Fi Password

In the router management interface of 192.168.10.1, click InstallInstall Settings, you can customize the 2.4G and 5G SSID and Password.

Configure EasyMesh

4.1. Step 1: set up the Controller
In the router management interface connected to the upper-level gateway (optical modem), select Network—EasyMesh—General, in the general settings page:

1. Fill in Mesh Controller in Device Name.
2. Select Controller in Role.
3. Click Save & Apply.

4.2. Step 2: set up the Agent

The Agent needs to be in the Bridge mode in 2.1. In the router management interface of other routers (except the router set in the first step), select Network—EasyMesh—General, in the general setting page:

1. Fill in Mesh Agent in Device Name.
2. Select Agent in Role.
3. Click Save & Apply.

4.3. Step 3: Two devices’ EasyMesh networking

After the two devices complete step 1 and step 2, the General interface will refresh, and the Start PBC button will appear. In the General interface of one of the devices, click  the Start PBC button or short press the device’s WPS button, and within two minutes enter the General interface of the other device, click the Start PBC button, or short press the WPS button of the device to trigger automatic network pairing. (Note that long-pressing the WPS key is rest)

4.4. EasyMesh networking of three or more devices
Perform step 2 on the third and more devices. After finishing step 2, perform step 3 for EasyMesh networking with routers that have been networked.

4.5. Check the device information in the topology

Network Topology:

Disable EasyMesh

In the router management interface, select Network-EasyMeshGeneral,  select disabled in Role and click Save. Then the EasyMesh network can be disabled.

When the router’s EasyMesh has been disabled, the device will depart from the original EasyMesh network. If to open EasyMesh again, please perform steps 2 and step 3 to rejoin the network.

Other information

1. After completing EasyMesh networking, the Controller device will synchronize its 2.4GHz and 5GHz SSID, password, and channel with the Agent device. That is, these configurations of the Agent device will be the same as the Controller device.
2. After modifying the SSID, password, and channel on the Controller device, the Controller device will synchronize these configurations to all Agent devices. Modifying the SSID and password on the Agent device will not be synchronized.
3. After the device restarts after a power failure, the device will restore the EasyMesh network group by default, and no connection settings are required.
4. If the EasyMesh function of the Controller device is disabled, the entire EasyMesh network will be disabled.
5. If the EasyMesh function of the Agent device is disabled, the device will leave the EasyMesh network.
6. If you need to switch the access mode of a certain Mesh device, you need to turn off the Mesh function of the device first, and then turn on the Mesh function to complete the switching of the access mode.
7. The Agent device is not supported to connect to other Mesh devices via Wi-Fi and wired at the same time. That is, the Agent device can only use one of the Wi-Fi and wired to connect to other Mesh devices.

FCC Warning Statement

FCC Radiation Exposure Statement: The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be
co-located for operating in conjunction with any other antenna or transmitter. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
‐‐Reorient or relocate the receiving antenna.
‐‐Increase the separation between the equipment and receiver.
‐‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
‐‐Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

After-sales Service Commitment

1. Implementation of the three guarantees regulations, seven days return, 15 days replacement, one-year warranty;
2. The free warranty period of the product is one year, calculated from the date of sale;
3. Under the following circumstances, three guarantees are not implemented, and paid maintenance is implemented:
   a. Failure caused by man-made damage, improper operation, or irresistible natural disasters;
   b. Failure caused by remodeling, disassembling, and assembling the product by yourself;
   c. Exceeding the validity period.

Manufacturer: Micronet Union Technology(Chengdu) Co., Ltd
Address: Room 502, Building 5, N.O. 528, Yuefei Road,
Shibata Street, Xindu District, Chengdu, Sichuan, China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>