YHEMI YMMKF005 Karaoke Microphone 2 Instruction Manual
- June 6, 2024
- YHEMI
Table of Contents
YHEMI YMMKF005 Karaoke Microphone 2
Please read the manual carefully before using the product and keep it properly
Product components
Product introduction
BOTTOM
Operation
Power on/off
Press POWER BUTTON for 2 seconds to start normally; long press POWER
BUTTON for 5 seconds to reset Bluetooth. When the microphone is power on,
press POWER BUTTON for 2 seconds to shut down.
Bluetooth pairing
First pairing
After the microphone is turned on, it will automatically enter the search
pairing mode. At this time, a prompt sound will be issued and the white light
will quickly flash. Find “YM microphone 2” on the Bluetooth settings page of
the mobile device for pairing.
Auto pairing
After the microphone is turned on, it will be automatically connected to the
last successfully paired device, and there will be a prompt tone after
connection. If the connection is not successful, it will automatically enter
the search pairing mode.
Reset pairing
Long press the power button for 5 seconds in the power off state to reset the
power on state, and the search pairing mode will be directly entered.
Wired connection
Connect the recording cable to the “icon” at the bottom of the microphone and
the interface of the mobile phone. Nd then turn on the relevant recording
functions of the mobile phone’s karaoke app, you can conduct wired recording.
Effect switch
When the microphone is in the power on state, click the power button to switch
the microphone sound effect. The effects are:
- Original sound effect
- Popular sound effect
- Fast song sound effect
- low song sound effect
- Folk song sound effect
- Rap sound effect
- Host sound effect
- Cartoon sound effect
- Monster sound effect
Remove the vocal
When the microphone is turned on and there is a song input, Long press the
Switch button to reduce the vocal part of the song. The specific effect is
slightly different according to different songs.
Mic volume and accompaniment volume adjustment Switching
When the microphone is turned on, click the switch button with voice prompt to
switch mic and sound adjustment;
Mic volume up and down
The microphone is turned on and in mic volume adjustment mode. Mic + once per
click Increase the volume by one grid, or press and hold for one grid every
0.3 seconds until it reaches the maximum with prompt;
Accompaniment volume addition and subtraction
The microphone is turned on and in the accompaniment volume adjustment mode.
Every click + accompaniment Increase the volume by one grid, or press and hold
for one grid every 0.3 seconds until it reaches the maximum with prompt.
Low power and charging function
When the battery power is less than 20%, there will be a prompt tone and an
orange light to remind charging in time. If the battery power is not charged
in time, the speaker will automatically shut down due to insufficient power;
connect the typec charging cable to the microphone to charge the microphone,
and the orange light will be on when charging.
Other functions
If there is no mobile phone pairing 15 minutes after power on, the speaker
system will shut down automatically.
Button menubar
LED menubar
Content of harmful substances
Parameter specification
- Bluetooth version: 5.0
- Battery: 3.7V 1500mAh
- Rated power: 5W
- Rated input: 5V 1A
- Charging interface type: type-C
- Size（L×W×H）: 86×86×218mm
- Weight: 261g
- Warning: the product contains lithium batteries and shall not be exposed to sun, sealed vehicles, fire baking or similar overheating environment for a long time.
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
*RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Manufacture: Beijing Yueme Technology Co.,Ltd. （MI Ecological Chain
Enterprise） Address: Room 105, Floor 1, Courtyard 1, 28 Houtun Road, Haidian
District, Beijing, China Service hotline:
400-601-5688
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>