Shenzhen Dayunlinks 43EXYD031 Video Baby Monitor User Manual

Video Baby Monitor 43EXYD031

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (l)this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation.

WARNING
Incorrect use of the product(s) may lead to safety risks. Therefore, we STRONGLY recommend reading the following instructions before using your product.

1. Keep the cord(s) away from children in case of strangulation (3 feet/ 1 meter away).
2. Put the product(s) in a dry place in case of short-circuit.
3. Use the AC adapter(s) provided by us ONLY. Using unauthorized charging cables and AC adapters may result in overheat even explosion.
4. Unplug the AC adapter(s) if you don’t use it(them).
5. Check your baby’s activities regularly as this product is not designed for supervision but for assisting your supervising.

PACKING LIST

CAMERA

MONITOR

1. VOX: The display screen enters the standby state, and the camera detection sound reaches 65dB. The display screen is on for one minute without alarm sound.
2. Camera Switch: Switch cameras if connected with 2 or more cameras.
3. Volume/Brightness: Press to adjust the monitor’s volume or brightness in the monitoring image.
4. Power/Sleep Button: Long press to turn on/off the monitor; short press to turn on/off the screen.
5. Sound Level LED: Low/high level shows low/high sound detected by the camera.
6. Menu/Back: Press to enter menu page or press as a Back button.
7. Left: Press to pan the camera leftward or to change your selection leftward.
8. Right: Press to pan the camera rightward or to change your selection rightward.
9. Zoom/OK: Press to Zoom in/out or to confirm your selection.
10. Up: Press to tilt the camera upward or to change your selection upward.
11. Down: Press to tilt the camera downward or to change your selection downward.
12. Talk: Press to talk to your baby in the monitoring image.
13. Charging Indicator: It gives off yellow light while the monitor is being charged.
14. Power Indicator: The green light turns on if connected to electricity.
15. Microphone
16. Reset Hole
17. Power Input
18. Antenna
19. Support Stand
20. Speaker
21. Battery Compartment

Note:

1. If you RESET with a pin, the monitor will be forced shutdown.
2. Do not open the battery compartment without official guidance.

GETTING STARTED

Step 1:

1. Connect the camera to the AC adapter.
2. Plug the AC adapter into a socket.

Note: Put the camera away from your baby (3ft/1m away at least).

Step 2:

1. Connect the monitor to the AC adapter.
2. Plug the AC adapter into a socket.
3. Long press the Power button to turn on the monitor then you can see the monitoring interface.

Note:
The monitor takes about 4 hours to be fully charged, and it lasts about 4-5 hours.

Notice:
The camera and monitor were paired already. This function is to add new cameras to the monitor.

1. Add cameras

2. Delete cameras

SOUND DETECTION

Explanation:
There are four options of sound detection, I (78dB), II (65dB) and Ill (60dB). I means the sound can be detected if it reached 78dB, and so on for II and Ill.

TEMPERATURE ALARM

Explanation:
indicates that the temperature value for high and low temperature alarms can be set.

Note: A sound/temperature alarm can be temporarily turned off by pressing any button on the monitor.

LULLABIES

Explanation:
This function is to comfort your baby when needed.

SLEEP MODE

Explanation:
This function is to prolong your monitor’s runtime by shutting down the screen.

Note: The screen will automatically light up if there is a sound alarm or a temperature alarm.

FEEDING

Explanation:
This function is to remind you of feeding your baby. OFF means you shut down the function; 2.5 hour means it reminds you every 2.5 hours and so on for the other options.

DATE/TIME

Explanation:
This function is to set Date/Time, turn on/off

SETTINGS

Explanation:
Restore factory settings and provide service support information.

ICONS EXPLANATION

Explanation:
You can open Live-Video-Loop function through short presses on the button until you see on the status bar. When Live-Video-Loop function is on, the connected cameras will automatically switch every 10 seconds. And if there is a sound/temperature alarm, the camera-switch function will pause temporarily.

FAQ

Ql. Why did I fail to connect the camera to the monitor?

• Make sure to plug the power adapter into the camera and socket firmly.
• Make sure the camera and the monitor is within the effective distance.

Q2. Why is the live video so blurry?

• Make sure there is no obstacle on the lens of the camera.

Q3. Why did the monitor make noise?

• The camera and monitor may be too close. Put them further apart.

Q4. Can I hear my baby when I turn off the screen?

• Yes. You should turn on Sound Detection, and it will wake up the screen and make a sound alarm if a loud sound is detected.

QS. Why is the picture black and white?

• The Night Vision Mode will be activated if the camera worked in a dark environment (Brightness Lux).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>