Wireless Edge BTR-13 Bluetooth Audio Receiver User Manual
- June 6, 2024
- Wireless Edge
Table of Contents
BTR-13
Bluetooth Audio Receiver
User Manual
Connection Diagram:
WARNING -When attaching RED ignition wire you will by-pass the internal On/Off switch
Turning Unit – ON / OFF
– Connect the yellow wire (Power +12v) and black wire (Ground -12v) wire to
power and ground securely.
– Press the control knob and hold it for over 3 seconds until you see the blue
LED light goes out (OFF) or stays lit for (ON).
Function Guide
| Instruction | Duration |
|---|---|
| Tap | Press once briefly |
| Turn | Turn knob once briefly |
| Turn and Hold | Turn the knob and hold it for 3 seconds |
| Press and Hold | Press the knob and keep it pressed in for 3 seconds |
Operation Guide
| Turn On and Off | Press and Hold |
|---|---|
| Play/Pause music | Tap knob once to pause, tab again to resume playing |
| Skip one track forward | Turn the knob clockwise |
| Skip one trackback | Turn the knob counter-clockwise |
| Adjust volume up | Turn and Hold the knob clockwise |
| Adjust volume down | Turn and Hold the knob counter-clockwise |
| Switch between Bluetooth and auxiliary input | Double Tap |
| --- | --- |
| Mounting Diagram | Removal Diagram |
Pairing Bluetooth Device
– Go to Settings on your smartphone and place Bluetooth° into discoverable
mode – Search for BTR- 1 3 device
– On the phone select BTR-1 3 to pair the device
– Once a device is paired each time the device is seen by the BTR-1 3 it
will automatically reconnect to the device. If no paired device is present,
the BTR- 1 3 will go into discoverable mode and can be connected by
another device
REMOTE IN Wiring Connection
For the following, the “YELLOW” wire must be connected to a constant +12
volt source of the vehicle. While the “BLACK” wire must be connected to a
vehicle grounded source/chassis.
– If using the MPS-BTK with a head-unit, connect BTR- 1 3 “RED” wire
to head-unit’s “REMOTE OUT” wire (This is typically a “BLUE WITH WHITE
STRIPE” wire on most head units)
– If using the BT14-1 3 with the vehicle’s ON/OFF key/switch, connect
BTR-1 3 “RED” wire to the vehicle’s Ignition wire.
NOTE: When connecting BTR-13 wiring to vehicle wiring remember to fuse
connection for added protection.
– If using the BTR-1 3 with a desire to have the controller be able to
be turned ON/OFF at any time (whether vehicle or head-unit is powered up or
not), DO NOT connect the “RED” wire to any other wire. Simply ensure the end
of the wire is tapped off to not make a connection with any other wiring
inside of the harness.
REMOTE OUT Wiring Connection
– If using the BTR-1 3 to power up an amplifier, or other device’s
“REMOTE IN” wire, connect “BLUE WITH WHITE STRIPE” (from the BTR- 1 3) to the
amplifier remote IN terminal or other device’s “REMOTE IN” wire (this can be
“BLUE WITH WHITE STRIPE’, “RED”, or other wire designated by that manufacture)
NOTE: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A
CLASS B DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE
DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE IN A
RESIDENTIAL INSTALLATION. THIS EQUIPMENT GENERATES USES AND CAN RADIATE RADIO
FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE
INSTRUCTIONS, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. HOWEVER,
THERE IS NO GUARANTEE THAT INTERFERENCE WILL NOT OCCUR IN A PARTICULAR
INSTALLATION. IF THIS EQUIPMENT DOES CAUSE HARMFUL INTERFERENCE 70 RADIO OR
TELEVISION RECEPTION, WHICH CAN BE DETERMINED BY TURNING THE EQUIPMENT OFF AND
ON, THE USER IS ENCOURAGED TO TRY TO CORRECT THE INTERFERENCE BY ONE OR MORE
OF THE FOLLOWING MEASURES:
– REORIENT OR RELOCATE THE RECEIVING ANTENNA.
– INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND RECEIVER.
-CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM THAT TO WHICH THE RECEIVER IS CONNECTED.
-CONSULT THE DEALER OR AN EXPERIENCED RADIO/TV TECHNICIAN FOR HELP CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT 70
THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.