DWARF CONNECTION DC-LINK-CLR2 Wireless Video Transmission User Guide
- June 6, 2024
- DWARF CONNECTION
Table of Contents
Quick start guide
DC-Link-CLR2 / X.LINK.S1
Getting Ready
- Connect the antennas to the SMA ports on your devices.
- Power your devices. Find details about proper powering options in the product manual provided on our website.
- Connect an SDI or HDMI signal to the transmitter’s input (SDI will be prioritized)
- Connect the receiver to the monitoring recording or distribution device of your joice.
Establishing a Connection
Use the power switch to turn on your transmitter and receiver(s). Make sure
that your devices are set to the same frequency channel. (see “Choosing a
Channel”)
It takes between 10-30 seconds for the transmitter to connect to the receiver.
During this brief period, the receiver’s video output displays “Waiting for
connection”.
Once the transmitter recognizes a video input, the video format will be
displayed on the OLED display.
DC-SCAN & Antenna Check
DC-SCAN is a built-in frequency scanner. To enter DC-SCAN, connect a monitor
to the HDMI output of your receiver, then press and hold the button on the
receiver for 3 seconds. The frequency scanner is only available on the HDMI
output. To leave DC-SCAN press and hold the button again. Entering DC-SCAN
from channel 0 will also show the antenna status: green = OK, red = not OK
Country-specific Regulations
Observe country-specific rules that prohibit the use of wireless transmission
under certain conditions!
Antenna positioning
Position the antennas on the transmitter and receiver as shown on the back of
your DC LINK device. This ensures the best possible RF performance. Install
the transmitter and the receiver as high as possible (at least 2 meters above
ground level) to maintain a good line of sight. During operation, try to keep
the transmitter and the receiver at similar heights.
Avoid obstacles such as walls, trees, water, and steel structures between
transmitter and receiver.
The connection is at its strongest when the flat surfaces of the transmitter
and receiver face each other.
RSSI Display
The RSSI (Wireless Received Signal Strength Indicator) display shows the
strength of the signal, allowing the operator to ensure the system is working
reliably. ****
Status | Description |
---|---|
0-1 LEDs | Radio signal strength is weak and artifacts are visible in the video |
signal
2-3 LEDs| Radio signal strength is normal and video quality is good
4-5 LEDs| Radio signal strength is very strong and video quality is very good
Dark Mode
Dark Mode turns off any lights on your DC LINK device. Press and hold + for 3 seconds to (de)activate Dark Mode. When in Encryption Mode, all receivers will react to changes made on the transmitter and follow into or out of Dark Mode automatically.
Choosing a Channel
To choose a channel on the transmitter/ receiver press MENU and select with the + and button. Press MENU to confirm.
**Master Channel Selection***
All receivers on the same channel react to channel changes of the transmitter and follow automatically.
**Multi Brand Connectivity***
All MKII receivers are equipped with the Multi-Brand Connectivity Feature that makes them compatible with the most common non-DFS WHDI wireless video transmitters on the market. Choose a channel from different frequency sets (marked with letters, e.g. A0) using the + and buttons and confirm with MENU. Channels used by DwarfConnection show no letter (0-9). For more detailed information, read the full product manual provided on our website.
OSD
Use the MENU button to navigate to the OSD menu and select the desired state by using the + or button. Confirm your selection with MENU. An indicator on the OLED display of the receiver shows the OSD state. With MKII devices, the OSD shows a Record Indicator, so you always know if the camera is recording.
Encryption Mode*
To activate encryption mode, press and hold the Menu button on your device to
enter the encryption menu. Use + or to check either ON or OFF and confirm
with MENU. The main menu will show either X ENC or ENC to indicate whether
encryption is on or off.
To link your devices, set your transmitter and all the receivers to the same
channel, then activate encryption on your transmitter.
All receivers will follow into encryption mode automatically. For more
detailed information, read the product manual provided on our website.
Fan Control & Cinema Mode
To switch the fan on the transmitter/receiver on or off, use the MENU button
to navigate to the fan menu and select the desired state by using + or turns
the fans on permanently. X turns the fans off. AUTO selects cinema-mode, which
triggers the fans using the record and stop signals of the camera. When
recording is over the fan starts automatically. (Cinema mode is bound to
metadata support and only available with SDI connection.)
Caution!
Switching off the fans may be required in some situations but doing this
permanently is not recommended.
Prolonged heat will affect the lifetime of your wireless equipment.
If the temperature of your device exceeds 75°C/165° F, turn on the fans
immediately! THERE IS NO EMERGENCY OUT!
Any damage caused by over-heating voids the warranty.
only on MKII devices
www.dwarfconnection.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>