actiMirror DESK21T03 Smart Mirror with Display User Manual
- June 6, 2024
- actiMirror
Table of Contents
actiMirror Desk21T-03 User Manual
Ver.210511
Mirror Outline
Turn ON the mirror: Plug in the power supply connector to the Power Input Jack
on the side panel. Press the Power Switch.
Turn OFF the mirror: When the mirror is turned ON, press the Power switch.
Turn ON the camera: Slid the Camera Switch on the side panel to the lower
position.
|
---|---
Turn OFF the mirror: Slid the Camera Switch to the upper position.
Connect to Internet
-
Connect to an internet port with an RJ45 connector cable to the LAN Port on the side
panel OR -
Click the Settings icon and set WIFI connection.
Connect to Bluetooth
Click the Settings icon and set the Bluetooth connection.
Display Brightness
Click the Settings icon and set the Display Brightness.
Sound Volume
At the bottom of the screen, click to increase the volume. Click to decrease the volume.
Stand Installation
A pair of stands and 6 screws are provided in the package. Please install the stands as below.
- After applying the double-size tape to the surface, it is recommended to leave it for around 20 mins.
- The mirror withstand should be installed on the surface of glass, metal or wood for the best stability effect.
- If the user finds out the adhesive power of the stand tape is insufficient or loosened, should call for the services to repair or replace it instead of using another tape by themselves.
Wall Mounting Instruction
- Drill 2 holes of 200mm clearance with a 10mm drill bit on the wall.
Insert the 2 wall plugs provided in the package into the holes. And screwing
on the 2 screws provided in the package with a cross-head screwdriver. Leaving
around 20mm clearance between the wall and the screw head.
Matching the 2 screws with the mounting holes on the mirror and hanging up the
mirror on the wall.
*Please use the 2 wall plugs and screws in the package or equivalent, for this 13kg mirror (Desk21T-03)
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
“ FCC RF Radiation Exposure Statement
Caution: To maintain compliance with the FCC’s RF exposure guidelines, place
the unit at least 20cm from nearby persons.”
- The device for operation in the band 5150-5250 MHz is only for indoor use
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>