Guangdong A Oktechnology Grand Developmentco 25-1-30BLE DC Motor User Guide

DC Motor 25-1-30BLE

A-OK
User Guide of AM25B Energy Saving Tuya Bluetooth Motor

Please secure the motor above 2 m to prevent child contact

Warnings: Important Security Instruction

Incorrect installation may cause severe injury Follow all the instructions and keep this installation guide in a safe place.

• AM2S motor is designed solely for the operation of roller shutters for home use. For any other use, please contact our technical department.
• The minimum inner diameter of the roller tube is 28 mm, but the tube must be chosen according to the weight and length of the apron. Consult the tube manufacturers’ charts.
• Do not operate the roller shutter if people or objects are in the movement area.
• The moving parts of the motor, installed at a height of less than 2.5m, must be protected.
• Before Installing the motor, remove all superfluous cords and take out of service any equipment not required for the motor to operate.
• Monitor the shutter when it is moving and stand clear until it is completely closed.
• Do not allow children to play with the fixed control devices. Keep remote control devices out of the reach of children.
• The operating device of an unlockable switch must be in direct view of the driven part, but kept away from the moving parts. It must be installed at a height of at least 1.5 m.
• The fixed control devices must be installed in a visible area.

I. Features

• Energy Saving Patent.
• Built-in Rechargeable Lithium Battery Pack.
• It has automatic correction function for the displacement generated by braking.
• The built-in control parts of motor are sealed well for better safety.
• Its easy to switch the mode between inching and interlock and control operation direction.
• Electronic limits setting,6 limits can be set (2 end limits and 4 middle limits).
• Short circuit protection & open circuit protection for sensor.
• Built-in low power Bluetooth module and APP intelligent control function.

II. Application

It can be fully charged with in 4 hours, Please unplug the charger when fully charged.

III. Operation Instruction

1. Switch ON/OFF : * After switching off the motor wouldn’t receive any remote signals NO more reaction when short press program button Every time when switch on. the motor may log twice which means non-networked

2. Programming Preparation: * When on the PROG mode. it exit automatically from PROG for no any operation maw 10s.

3. Pairing the remote:

4. Dot Move & Continuous move convention 

5. Change Direction

6. Delete  Single Code

7. Delete all memories

8. Adjusting Angle by inching

9. First limit position setting

10. O ther limit position setting

11. Limit position fine-tuning

12. Delete the limit position

13. Reset Bluetooth
Short press PROG for 5 times by 1 press per 1 second. Hold it for 35 when the 5th press, then the motor jog once, which means Bluetooth has been reset. Here comes the mode of matching network, the green indicator light fleshes

14. Supplemental Instruction
a .Maximum 6 limit positions can be set The furthest 2 positions are called up and down limit position. The others are called middle limit positions.

b. The first limit position can only be set as up or down limit position. if the first one is up limit position, which means other positions can only be set below the position. in the same way.it is the down limit position, the other limit positions can only be set above It.

c. Each limit position can be fine-tuned and deleted separately.(The first limit position can only be tine-tuned, not deleted separately but it can be deleted when deleted all memories)

d. For inching mode. the motor jog a little and then stop when press the up/down button for 1s. The operation will go on when press the up/down button for ever 1 s

e. For interlock mode, the motor will go directly to the up and down limit position without any slop at middle limits when press the up and down button twice at the speed of once every second.

f. When motor is operating and the voltage reaches below 6.2V,it mean voltage shortage with flashing red indicator light, and interlock mode turn into inching mode The motor stop working when the voltage’s lower than 5.5V.

g. The indicator light turns red when charging it turn green when finishes charging.

FCC Compliance Notice

This device complies with part 15 of the FCC Rules. Operation is sunned to the following two conditions: (1) This device may rot .use harmful interference. and (2) this device must accept any interference received, including interference that may cause undesired operation. My Mangey or modifications not expressly approved by the party responsible for compliance could void Me user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class 13 digital device, pursuant to pad 15 of the FCC Rules. These limits are design. to provide reasonable pro..on against harmful Interference in a residential installation. This equipment generates, uses a. can radiate radio frequency energy a., if not installed and used in accordance with the Instructions, may cause harmful interference . radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by fuming the equipment off and on, Me user is encourage. to try to correct the interference by one or more of the following measures:

• Reorient or donate the receiving antenna.
• Increase the separation between the equipment and rd..,
• Conned the equipment into an outlet on a circuit different from Mat to which Me receiver is connected.
•  Consult the dealer or an experienced radio /TV technician fix- help.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.

ISEDC RSS warning
This device complies with Innovation, Science and Economic Development Canada Compliance licence – exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>