BOSCH Art 23 Easytrim Accu Battery Cordless Grass Trimmer Instruction Manual
- June 6, 2024
- Bosch
Table of Contents
BOSCH Art 23 Easytrim Accu Battery Cordless Grass Trimmer
- F 016 800 178
-
- F 016 800 177
(ART 23/2300 EASYTRIM ACCU)
F 016 800 183
(ART 26/2600 EASYTRIM ACCU)
- F 016 800 177
Safety Notes
Warning! Read these instructions carefully, be familiar with the controls
and the proper use of the trimmer. Please keep the instructions safe for later
use.
Explanation of symbols on the trimmer
- General hazard safety alert.
- Read instruction manual.
- Wear eye protection.
Beware of thrown or flying objects to bystanders. Keep bystanders a safe distance away from the machine. Remove battery before adjusting or cleaning, and before leaving the machine unattended for any period.
Do not work in the rain or leave the trimmer outdoors whilst it is raining.
-
Never operate the trimmer with damaged guards or shields or without guards or shields in position.
Do not use the charger if the cord is damaged. -
Before using the machine and after impact, check for signs of wear or damage and repair if necessary.
-
Do not operate the trimmer when barefoot or wearing open sandals, always wear substantial footwear and long trousers.
-
Never allow children or people unfamiliar with these instructions to use the trimmer. Local regulations may restrict the age of the operator. When not in use store the trimmer out of reach of children.
-
This appliance is not intended for used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.Children should be supervised to ensure that they do not play with the appliance.
-
Never work with this trimmer while people, especially children or pets are nearby.
-
The operator or user is responsible for accidents or hazards occurring to other people or their property.
-
Wait until the blade has completely stopped before touching it. The blade continues to rotate after the trimmer is switched off, a rotating blade can cause injury.
-
Work only in daylight or in good artificial light.
-
Avoid operating the trimmer in wet grass, where feasible.
-
Switch off when transporting the trimmer to and from the area to be worked on.
-
Switch on the trimmer with hands and feet well away from the rotating line.
-
Do not put hands or feet near the rotating blade.
-
Never fit metal cutting elements to this trimmer.
-
Inspect and maintain the trimmer regularly.
-
Have the trimmer repaired only by an authorized customer service agent.
-
Always ensure that the ventilation slots are kept clear of debris.
-
Switch off and remove battery from the trimmer:
whenever you leave the machine unattended for any period
before replacing the blade
before cleaning or working on the trimmer. -
Store the machine in a secure dry place out of reach of children. Do not place other objects on top of the machine.
-
Replace worn or damaged parts for safety.
-
Ensure replacement parts fitted are Bosch approved.
-
Ensure the switch is in the off position before inserting battery pack. Inserting the battery pack into machines that have the switch on invites accidents.
-
Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
-
Use machines only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
-
When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
-
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Technical data
Technical data|
---|---
| | |
Trimmer| | ART 23 EASYTRIM ACCU/ ART 2300 EASYTRIM ACCU| ART 26
EASYTRIM ACCU/ ART 2600 EASYTRIM ACCU
Part number (typ)| | 3 600 H78 H..| 3 600 H78 J..
No-load speed| [min-1]| 9 500| 9 000
Cutting circle| [cm]| 23| 26
Weight (without optional extras)| [kg]| 1.9| 2.0
Serial Number See serial No 14 (rating
plate) on machine.
Battery type| | NiCd| NiCd
Part number (typ)| | 2 607 335 533| 2 607 335 533
Nominal Voltage| [V]| 14.4| 14.4
Capacity| [Ah]| 1.5| 1.5
Charging time (empty battery)| [min]| 250| 250
Battery charger| | AL 1404| AL 1404
Part number (typ)| | 2 607 225 …| 2 607 225 …
Charging current| [A]| 0.4| 0.4
Allowable charging temperature range| [°C]|
0–45
|
0–45
Intended Use
The product is intended for the cutting of grass and weeds under bushes, as
well as on slopes and edges that can not be reached with the lawnmower.
Intended Use is related to operation within 0 °C and 40 °C ambient
temperature.
Introduction
This manual gives instructions on the correct assembly and safe use of your machine. It is important that you read these instructions carefully.
Delivered Items
Carefully remove the machine from its packaging and check that you have all the following items:
- Trimmer
- Cutting guard
- Cutting disc
- Blades
- Battery charger
- Operating instructions
When parts are missing or damaged, please contact your dealer.
Operating Controls
- On/Off switch
- Handle
- Guide handle
- Shaft, upper
- Shaft, lower
- Trimmer head
- Ventilation slots
- Cutting guard
- Rechargeable battery
- Battery charger
- Charging compartment 12 LED indicator
- Mains plug**
- Serial Number
Country specific
Not all of the accessories illustrated or described are included as standard
delivery.
For Your Safety
Warning! Switch off, remove battery from ma-chine before adjusting or cleaning. The blade continues to rotate for a few seconds after the trimmer is switched off. Caution – do not touch rotating blade.
Charging Procedure
The charging procedure starts as soon as the mains plug is plugged into the
socket and the battery 9 is inserted into the charging compartment 11.
The green LED
12 is not a charge control indicator! When the green LED is lit, it indicates
that a charging current flows. After the end of the charging process (approx.
3 h–4 h), pull the mains plug of the battery charger from the socket and
remove the battery.
The battery should not be charged for longer than 5.5 hours. A temperature increase of the battery indicates that it is fully charged.
Charging Advice
With continuous or several repetitive charging cycles without interruption,
the charger can warm up. This is not harmful and does not indicate a technical
defect of the unit. A battery 9 that is new or has not been used for a longer
period does not develop its full capacity until after approximately 5
charging/discharging cycles. Leave such batteries 9 in the charging
compartment 11 until they have clearly warmed up. A significantly reduced
working period after charging indicates that the batteries are worn out and
must be replaced.
Assembly
Do not connect the battery before product is completely assembled.
Ensure product is assembled in the following or-der:
-
An Assemble trimmer shaft Push the upper shaft 4 and lower shaft 5 together until a click can be heard.
Note: Once the upper and lower shaft is assembled it can not be disassembled. Ensure internal cable is not trapped or twisted. -
B Mounting the Cutting Guard Place the cutting guard 8 on the trimmer head 6.
Hook the guard onto trimmer head and push until secure fitting.
Push rear of guard until secure (click). -
C Fitting Cutting Disc/Fitting Blade Press cutting disc 15 onto drive adaptor as shown (click).
Fit the blade, place the blade 16 over the pivot 17 and pull outwards until it snaps into place. -
D Cutting GrassMove the trimmer left and right, keeping it well away from the body.
The trimmer can efficiently cut grass up to a height of 15 cm. Cut taller grass in stages.
Cutting and Edging
Remove stones, loose pieces of wood and other objects from the cutting area.
The blade continues to rotate for a few seconds after the trimmer is switched
off. Allow the motor/blade to stop rotating before switching “on” again. Do
not rapidly switch off and on. Switching On and Off
Press switch 1 and hold depressed. Release switch 1 for switching off.
Cutting Around Trees and Bushes
Carefully cut around trees and bushes so that they do not come into contact
with the cutting line. Plants can die if you damage the bark.
Battery duration
Battery duration is dependent on the working conditions:
Maintenance
Before any work on the machine itself, the re-move battery from machine.
Note:
To ensure long and reliable service, carry out the following maintenance
regularly. Regularly check for obvious defects such as loose fixings, and worn
or damaged components. Check that covers and guards are undamaged and
correctly fitted. Carry out necessary maintenance or repairs before using.
If the trimmer should happen to fail despite the care taken in manufacture and
testing, repair should be carried out by an authorized customer service agent
for Bosch garden products. For all correspondence and spare parts orders, al-
ways include the 10-digit part number (TYP) from the nameplate of the machine!
Blade Maintenance
Before any work on the machine itself, the re-move battery from machine.
To remove the worn blade 16 push in direction of the arrow until it snaps off
the pivot 17. Clean the pivot 17 of any residual plastic/debris with a sharp
knife.
To refit the new blade 16 place the eyelet over the pivot 17 and pull outwards
until it snaps into place.
Note: Only use Bosch replacement blades. They have been developed
specially for improved cutting performance. The use of other cutter blades
will lead to a deterioration in performance and possible damage to the
product.
After Trimming/Storage
Stop and remove the battery from the product. Ensure the battery is removed before storage.
Clean the exterior of the machine thoroughly using a soft brush and cloth. Do not use water, solvents or polishes. Remove all grass and debris, especially from the ventilation slots 7. Turn the machine on its side and clean the cutting guard 8 inside. If grass cuttings are compacted, remove with a wooden or plastic implement. Battery should be stored between 0 °C – 45 °C; incorrect storage could result in the battery being damaged.
Fault Finding
The following table gives checks and actions that you can perform if your
machine does not operate correctly. If these do not identify/remedy the
problem, contact your service agent. Warning: Switch off and remove battery
before investigating fault.
| Symptom | Possible Cause | Remedy |
|---|---|---|
| Can not fit Guard over cutting disc | Incorrect assembly | Remove cutting disc |
and fit guard, see also “Product assembly”
Machine fails to operate| Battery discharged| Recharge battery, see also
“Charging advice”
Machine functions intermittently| Machines internal wiring damaged On/Off
switch defective| Contact Service Agent Contact Service Agent
Excessive vibration/ noise| Machine fault Blade broken| Contact Service Agent
Replace blade
Cutting time low on one battery charge| Battery not used for long period or
initial usage
Grass too high Battery worn out
| Fully charge battery, see also “Charg- ing advice”
Cut in stages Replace the battery
Blade will not move| Battery discharged
Machine fault
| Recharge battery, see also “Charging advice”
Contact Service Agent
Machine is not cutting| Blade broken
Battery not fully charged
Grass entangled around cutting disc
| Replace blade
Recharge battery, see also “Charging advice“
Remove grass
No charging procedure possible due to defective battery| The contacts of the battery are contaminated
The battery is defective, due to a dis-connection in the battery (individual cells)
| Clean the contacts (e. g. by inserting and removing the battery several times) or replace the battery, as re-quired
Replace the battery
The LED indicator 12
does not light up after plugging the mains plug into the socket and insert- ing the battery into the charging compartment 11
| The charger plug is not inserted (properly)
Socket, cable or charger are defective
| Insert the plug (fully) into the socket
Check the mains voltage and if necessary, have the battery charger checked by an authorized customer service station for Bosch power tools
Disposal
Power tools, accessories and packaging should be sorted for environmental-
friendly recycling.
Only for EC countries:
Do not dispose of power tools into household waste! According to the European Directive 2002/96/EC on waste electrical and electronic equipment and its incorporation into national law, products that are no longer suitable for use must be separately collected and sent for recovery in an environmentally- friendly manner.
After-Sales Service and Customer Assistance
Our after-sales service responds to your questions concerning maintenance and
repair of your product as well as spare parts. Exploded views and information
on spare parts can also be found under: www.bosch-pt.com
Our customer consultants answer your questions concerning best buy,
application and adjustment of products and accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: SPT-Technical.de@de.bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
Australia, New Zealand and Pacific Islands Robert Bosch Australia
Pty.Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: + 61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
Declaration of Conformity
Measured values determined according to 2000/14/EC (1.60 m height, 1 m
distance away) and EN ISO 5349.
Typically the A-weighted noise levels of the product are: Sound pressure level
72 dB (A); Guaranteed sound power level lower than 94 dB(A). Uncertainty K = 3
dB.
The typical hand/arm vibration is below 2.5 m/s2. We declare under our sole responsibility that the product described under „Technical data“ is in conformity with the following standards or standard-ization documents: EN 60335 (battery powered product) and EN 60335 (battery charger) according to the provisions of the directives 2006/95/EC, 2004/108/EC, 98/37/EC (until 28 D ec 2009), 2006/42/EC (from 29 Dec 2009), 2000/14/EC. 2000/14/EC: Measured sound power level 88 dB(A). Conformity assessment procedure according to Annex VI.
Notified body: SRL, Sudbury, England
Notified body identification number: 1088
Technical file at: Bosch Lawn and Garden Ltd., PT-LG/EAE, Stowmarket, Suffolk
IP14 1EY, Eng-land
08
Leinfelden, 01.01.2008
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>