RED MAGIC PA3103 RedMagic Dual-core Cooler User Guide

RED MAGIC PA3103 RedMagic Dual-core Cooler User Guide

Product Overview

Schematic diagram of the product:

• Pull the gripper on both sides to fit the mobile phone.
• Only suitable for mobile phones with a width between 70mm and 84mm.

Installation and operation

1. Download and install APP
   Please scan the QR code below to download and install the APP. RedMagic mobile phone supports you to dial the game button to configure and operate in the game space.
   

2. Activate the RedMagic dual-core cooler

3. Fix the cooler on the back of the phone and make sure that the fit is as tight as possible.

4. Connect the charger through Type-C data cable and ensure that the output power of the charger is 5V/2A or above.

5. The cooler automatically activates the heat dissipation when the gripper is pulled open and energized.

6. Set the RedMagic dual-core cooler

7. Activate the Bluetooth of the mobile phone, and conned the cooler in the RedMagic mobile phone game space or APP.

8. Set the lighting effect for the cooler. the heat dissipation high and low gears and switch mode.

  * The cooler with Hall switch, when pulling open the gripper of the cooler, the switch is automatically opened by default, you can choose to set in the game space or APP.
  * When the cooler is working, the temperature of the cooler decreases, the hot air in the environment will condense into water droplets attached to the surface of the cooler when it is cold, which is a normal phenomenon.
  * When you stop using the device, please disconnect the power in time.

Product Specifications

• Product name: RedMagic dual-core cooler

• Product model: PA3103

• Connection method: Bluetooth 4.2

• Supported platforms: Android 6.0 and above, ios12 and above

• Power supply interface: Type-C

• Package contents:
  

  • RedMagic dual-core cooler x1
  • Type-C data cable x1
  • User Guide x1

Disposal of our Old Device

• When the wheelie bin symbol is attached to a device, it means the device is covered by the European Directive 2012/19/EU.
• All electrical and electronic devices should be disposed of separately from normal household waste via designated collection points provided by government or local authorities.
• The correct disposal of electrical and electronic products will help protect the environment and human health.

EU Declaration of Conformity (DoC)

Hereby, Nubia Technology Co., Ltd declares that this device is in conformity with the Radio Equipment Directive: 2014 / 53 / EU.
For the declaration of conformity, visit http://www.nubia.com/en/support.php?ardownload.

Declaration of RoHS 2.0 Compliance

We’re determined to reduce the impact we have on the environment and take responsibility for the earth we live on. So this document allows us to formally declare that the PA3103, manufactured by Nubia Technology Co., Ltd, fully complies with the European Parliament’s RoHS (Restriction of Hazardous Substances) 2.0 Directive 2011/65/EU, with respect to all the following substances:

1. Lead (Pb)
2. Mercury (Hg)
3. Cadmium (Cd)
4. Hexavalent Chromium (Cr (VI))
5. Polybrominated biphenyl (PBB)
6. Polybrominated diphenyl ether (PBDE)
7. Di(2-ethylhexyl) phthalate(DEHP)
8. Dibutyl phthalate (DBP)
9. Benzyl butyl phthalate (BBP)
10. Diisobutyl phthalate(DIBP)

Our compliance is witnessed by written declaration from our suppliers. This confirms that any potential trace contamination levels of the substances listed above are below the maximum level set by EU 2011/65/EU, or are exempt due to their application.

The PA3103 manufactured by Nubia Technology Co., Ltd meets all the requirements of EU 2011/65/EU.

FCC Statement

FCC regulatory conformance:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

RF Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Warranty Provisions

Warranty period: The warranty period commences from the date of purchase. The product and other accessories carry a warranty period according to local regulations and policy. The date on the proof of purchase or any other valid voucher will be considered as the date of purchase. For more detailed warranty information, please consult your local dealer or visit Nubia official website: http://www.nubia.com/en/

Non-Warranty Provisions

The warranty doesn’t cover products which have been handled in any of the following cases:

• Products malfunctioned or damaged due to misuse, improper use, abuse, negligence, or any improper use not according to the user manual.
• Product repaired,replaced or altered by any person other than Nubia customer service center.
• Products malfunctioned or damaged due to natural calamity, force majeure, unpredictable accidents and any other factors beyond the control of Nubia Technology Co., Ltd.
• Product altered, converted, or exchanged to meet the requirements of local electrical conditions, safety standards and communication systems by any person other than Nubia service center.
• Product whose serial number or warranty sticker is missing, damaged, or altered.
• Products which expire the warranty period specified in warranty card. If those provisions conflict with local laws and regulations, it subject to the local regulation.
  

Warranty Card

Warranty Information

Name: ___

Purchase Date: _____

Charger SIN: __

Battery SIN: __

Dealer: __

Dealer Tel: ___

Notes
if the product does not contain charger or battery, you don’ t have to fill in the serial number.
This certificate will become effective only after stamped by a dealer authorized by Nubia Technology Co., Ltd.

Nubia Technology Co., Ltd.
18/F,Building 2,Chongwen Park,Nanshan Zhiyuan,3370 Liuxian Road,Nanshan
District,Shenzhen 518055, China.
ServiceHotline: 400-700-6600
Official: website:www.nubia.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>