sinope SW2500ZB Smart Light Switch Installation Guide
- June 6, 2024
- sinope
Table of Contents
sinope SW2500ZB Smart Light Switch
YOUR SW2500ZB LIGHT SWITCH
Light turned ON = Blue
Light turned OFF = Amber
The intensity of the indicator light can be changed from Neviweb and some
compatible Zigbee gateways.
SINGLE POLE WIRING DIAGRAM
WAY WIRING DIAGRAM
INSTALL YOUR LIGHT SWITCH
-
Make sure that the breaker for your switch is OFF at the main electrical panel, then remove the old switch.
-
Use the provided connectors to connect the wires as follows:
- Red Load
- Black Line
- White Neutral
- Blue None*
*Note: For a single pole installation, do not remove the label on the blue wire. For a 3-way installation, consult the 3-way wiring diagram above.
-
Use the provided screws to secure the light switch to the electrical box, then replace the wall plate.
-
Power up the switch.
Make sure to firmly tighten the wire connectors for a secure connection. A loose connection can be a fire hazard. Special CO/ALR solderless connectors must be used when connecting with aluminum conductors.
ADD YOUR SWITCH TO THE GT130 AND NEVIWEB
- If you do not have an account yet, download the Neviweb app for iOS or Android to create an account and add your device.
- Tap the , then select “Add Device”.
- Follow the steps of the Installation Wizard.
DISCONNECT YOUR LIGHT SWITCH FROM THE GT130 GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM
To disconnect your light swtich from the GT130 gateway or a compatible Zigbee system, press the 2 buttons of the light switch simultaneously for 10 seconds.
CONNECT YOUR LIGHT SWITCH TO THE GT130 GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM
-
Initiate the connectivity session by pressing the RF signal button on the GT130 gateway. The indicator light will start flashing.
Compatible Zigbee gateway: referto the installation guide for the latter. -
Connect your dimmer to the network by simultaneously pressing the two buttons for 1 second. On the switch: The indicator flashes
blue when the device is connecting.
The indicator turns red = Failed
Refer to the “support” section of our Website to troubleshoot the unit.
The indicator turns green = Connected
After a few seconds, the indicator changes color depending on the switch status. (Turned ON = blue, Turned OFF = amber)
-
Connect all your compatible Zigbee devices the same way, by going to the next closest device.
-
When all your devices are connected, close the connectivity session of your GT130 gateway or your compatible Zigbee gateway.
TECHNICAL SPECIFICATIONS
- Operating voltage : 120 Vac, 60 Hz
- Operation temp.: 0 °C to 40 °C (32 °F to 104 °F)
- Storage: -20 °C to 50 °C (-4 °F to 122 °F)
- Standard UL: Conforms to ANSI/UL Std. 916
- Standard CSA: Certified to CAN/CSA Std. C22.2 No205
PROVIDED CONNECTORS SPECIFICATIONS:
Stripping length: 16 mm
Wires: 22-10 AWG, Cu
Combinations: Max. 2 #12 & 2 #14, Min. 3 #20 Sol.
MAXIMUM LOAD:
- 450 W: LED, CFL, Halogen
- 600 W: Incandescent
- 1800 W: Resistive
- 1/2 HP: Ceiling fan
Protocol: Zigbee 3.0
Frequency: 2.4 GHz
Transmission power: +20 dBm
Receiver sensitivity: -108 dBm
Neviweb® is a registered trademark of Sinopé Technologies Inc. in Canada and the United States. Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc., registered in the U.S. and other countries. Google Play and the Google Play logo are trademarks of Google Inc.
Transmitter Module IC: 22394-ZBM1501 / FCC ID:2AK2T-ZBM1501
This device complies with Industry Canada license exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device does not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of
the device.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment OFF and
ON, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of their products against
defects in material and workmanship for a 3-year period from the date of
purchase, under normal use and service, when proof of purchase of such is
provided to the manufacturer. This warranty does not cover any transportation
costs that may be incurred by the consumer. Nor does it cover a product that
has been improperly installed, misused or accidentally damaged.
The obligation of SINOPÉ TECHNOLOGIES INC., under the terms of this warranty,
will be to supply a new unit and this releases the manufacturer from paying
the installation costs or other secondary charges linked to replacing the unit
or the components.
Warnings
The installation of this light switch must be performed by a certified
electrician and comply with the national and local electrical codes and
regulations. This light switch requires a neutral wire. If your electrical box
does not have a neutral wire, you can either add one or install the light
switch at a different location.
For more information, visit our Website:
www.sinopetech.com
Documents / Resources
|
sinope SW2500ZB Smart Light
Switch
[pdf] Installation Guide
SW2500ZB, Smart Light Switch, SW2500ZB Smart Light Switch
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>