VECTRONIC V2 GPS Collars Plus 2021 User Guide
- June 6, 2024
- VECTRONIC
Table of Contents
- Unwrap collars and verify that you have received all ordered equipment.
- Install GPS PLUS X Collar Manager Software
- Register your collars in GPS PLUS X
- Connecting your collars with the PC
- Get to know your collars
- Deploy your collars
- Want a quick and simple overview of your collar’s whereabouts?
- You need further information?
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
GPS Collars
Quickstart Guide
PROGRAMMING OF COLLARS, SENSORS, AND EQUIPMENT IS PART OF OUR FREE CUSTOMER
SERVICE.
ALWAYS DOUBLE-CHECK THAT YOUR REQUIRED SETTINGS ARE CORRECT BY CHECKING THE
COLLAR INFO FILES ON THE SUPPLIED USB THUMB DRIVE.
NOTE THAT OUR PRODUCTS ARE DELIVERED UNDER THE EXCLUSION OF WARRANTY FOR
CONFIGURATION.
IMPORTANT NOTE: You must always test the collars AT LEAST 48 hrs before deployment to make sure they are working in your area and you are receiving data from one of our communication platforms. For warranty, reasons do not deploy untested collars to animals.
Unwrap collars and verify that you have received all ordered equipment.
Make sure that the magnets are attached to the electronic housing and the Drop
Offs (if ordered).
On the included USB drive you will find your collar registration keys (.keyx),
collar information files, GPS PLUS X (the software used to manage collars and
data), as well as, all drivers and manuals for all equipment.
DO NOT PLUG ANY DEVICE EXCEPT THE USB THUMB DRIVE INTO YOUR PC AT THIS POINT!
Install GPS PLUS X Collar Manager Software
Plug the USB drive into your PC and follow the installation instructions for
GPS PLUS X Collar Manager Software by selecting Set-Up your System.
Start the program when finished.
Register your collars in GPS PLUS X
Go back to the USB drive and copy all necessary key files (.keyx) to your computer according to the installation guide. You can then register your collars in the Configuration Tree in GPS PLUS X.
Connecting your collars with the PC
Plug the collar interface device, that you received with your collars, into
your PC. The communication device should then pop up in GPS PLUS X under
Devices.
If not, please refer to the GPS PLUS X Manual.
NOTE: There are different interfaces for the different collar types.
Get to know your collars
Make yourself familiar with the collars.
Check their Setup with the info files. Run a few test trials (1-2 days) to
make sure the collars work and you understand the messages you will receive
from the collar once deployed.
FOR TESTING: Place the collars outside with a clear view to the sky at least
one meter apart from each other, remove the upper magnet (round) and leave
until data is received through one of the communication platforms. After the
test, turn the collar off again by reattaching the magnet.
Do not test the Drop Off, it can only be used once!
Deploy your collars
When deploying the collars, make sure that the silver connector cap that
covers the communication port on some of the models, not all, is secured and
the batteries are correctly fixed and sealed.
Remember to remove the round magnet from the collar, as well as, the
cylindrical magnet from the Drop Off!
Want a quick and simple overview of your collar’s whereabouts?
Check out our new web interface INVENTA!
Visit inventa.vectronic-wildlife.com and register now!
You need further information?
Refer to the manuals for further information and assistance. If in doubt, feel free to contact ELECTRONIC Aerospace customer support. For news about firmware updates or anything else regarding our products please subscribe to our newsletter or contact us directly!
https://inventa.vectronic-wildlife.com/auth/login
https://inventa.vectronic-wildlife.com/auth/login
https://www.vectronic-aerospace.com/gps-plus-x/
https://www.youtube.com/watch?v=CMYe71nHwh8
VECTRONIC Aerospace GmbH
Berlin, Germany
Phone: +49 30 6789 4990| VECTRONIC Aerospace USA
Iowa, USA
Phone: +1 319 626 2267| VECTRONIC Aerospace CA
Ontario, Canada
Phone: +1 905 535 1514
---|---|---
www.vectronic-aerospace.com
[email protected]