Delta Networks VCB601-ZB01 802.15.4 Zigbee Module User Manual
- June 6, 2024
- Delta Networks
Table of Contents
VCB601-ZB01 User Manual
EFR32MG1B232F256GM48 802.15.4 Zigbee Module
FCC ID:2AMVP-VCB601V2
Rev. 1.0 2017/07/18
Notice:
-
Delta Networks (XIAMEN) LTD. reserves the right to change specifications detailed in this document at any time without notice, and assumes no responsibility for any
errors within this document. -
This document contains proprietary technical information in which is the property of the Delta Networks (XIAMEN) LTD. and shall not be disclosed to others in the whole or in part, reproduced, copied, or used as the basis for design, manufacturing, or sale of apparatus without written permission of Delta Networks (XIAMEN) LTD. Inc.
Product Overview
1.1. General Description
The VCB601-ZB01 is a Zigbee data collector module that can collect data from
other devices With a TTL serial port and then send out data through Zigbee.
This device is a built-in Silicon LAB EFR32MG1B232F256GM48 which is a highly
integrated single-chip low power Wireless on Chip controller. The
EFR32MG1B232F256GM48 combines an ARM-Cortex M4 with DSP instruction, MCU, and
2.4G RF in a single chip. It provides a UART interface. It also provides a
bunch of configurable GPIOs which are configured as digital peripherals for
different applications and controls.
1.2. Features
- IEEE802.15.4 in 2.4G Band compatible
- UART interface
- The dual 10-pins header connector
| Standard | IEEE 802.15.4 |
|---|---|
| Data Rate | <250kbps |
| Modulation | DSSS with OQPSK |
| Operating Frequencies | 2.400~2.483.5GHz |
| Antenna Connector | R-SMA connector |
2. Revision History
| Revision | Date | By Whom | Remark |
|---|---|---|---|
| 1 | 07/18-2017 | Yueqing. xu | Initialize |
Statement
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
– Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following
conditions:
- The antenna must be installed such that 20 cm is maintained between the antenna and users, and
- The transmitter module may not be co-located with any other transmitter or
antenna.
As long as the 2 conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: 2AMVP-VCB601V2”. The grantee’s FCC ID can be used only when all FCC compliance requirements are met.
Manual Information To the End-User
The OEM integrator has to be aware not to provide information to the end-user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end-user manual shall include all required regulatory information/warning.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>