iRobot Roomba i7 Smarter Robot Vacuum Owner’s Manual

**iRobot Roomba i7 Smarter Robot Vacuum Owner’s Manual

**

iRobot Roomba i7 Smarter Robot Vacuum Owner’s Manual

Safety Information

Important Safety Information

This owner’s guide includes information for Regulatory Model(s): RVB-Y2

SAVE THESE INSTRUCTIONS

WARNING: When using an electrical appliance, basic precautions should always be followed, including the following:

READ ALL INSTRUCTIONS

WARNING: To reduce the risk of injury or damage, read and follow the safety precautions when setting up, using and maintaining your robot.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• This is the safety alert symbol. It is used to alert you to potential physical injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
• Risk of electric shock
• Class II equipment
• Rated power output, d.c.
• Read operator’s manual
• General symbol for recycling
• Risk of fire
• For indoor use only
• Rated power input, d.c.
• Keep out of reach of children
• Rated power input, a.c.
• Separate Supply Unit

WARNING: Indicates a hazardous situation that, if not avoided, could result in death or serious injury.

CAUTION: Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.

NOTICE: Indicates a hazardous situation that, if not avoided, could result in property damage.

GENERAL

WARNING

• Your robot is not a toy. Small children and pets should be supervised when your robot is operating.

• Do not sit or stand on your robot or charging station.

• Do not use unauthorized chargers. Use of an unauthorized charger could cause the battery to generate heat, smoke, catch fire, or explode.

• Your robot comes with a region approved power supply cord and is designed to be plugged into a standard household AC power outlet only. Do not use any other power supply cord or power strip. For replacement cords, please contact Customer Care to ensure proper selection of country specific power supply cord.

• Do not open your robot or charging station other than instructed in the owner’s guide. There are no user serviceable parts inside.
  Refer servicing to qualified service personnel.

• Risk of electric shock, use indoors in dry location only.

• Do not handle your robot or charging station with wet hands.

• Store and operate your robot in room temperature environments only.

• If the room to be cleaned contains a balcony, a physical barrier should be used to prevent robot access to the balcony and ensure safe operation.

CAUTION

• Do not operate the robot in areas with exposed electrical outlets in the floor.

• If the device passes over a power cord and drags it, there is a chance an object could be pulled off a table or shelf.
  Before using this device, pick up objects like clothing, loose papers, pull cords for blinds or curtains, power cords, and any fragile objects. Extinguish candles. Shutoff space heaters.

• Be aware that the robot moves on its own. Take care when walking in the area that the robot is operating in to avoid stepping on it or tripping over it.

• Do not use this device to pick up sharp objects, glass, or anything that is burning or smoking.

• Perform the required maintenance per the Owner’s Guide to ensure safe operation of the robot and charging station.

NOTICE

• This robot is intended for dry floor use only. Do not use this device to pick up spills. Do not allow your robot or charging station to become wet.
• Do not place anything on top of your robot or charging station.
• The failure to maintain cleanliness of charger contacts could result in loss of ability for the robot to charge the battery.
• Before running your robot on carpets or rugs, ensure that the carpets or rugs are compatible with vacuums using bars or brushes. Using your robot on a carpet or rug that is not compatible could result in damage to your carpet or rug.
  Contact your carpet or rug manufacturer with questions on compatibility

CHARGING STATION

WARNING

• Do not use a charging station with a damaged cord or plug if the cord or plug is damaged, it must be replaced.

• Always disconnect your robot from the charging station before cleaning or maintaining it.

• Do not use the charging station as a step.

• Charge your robot only with the power supply provided.
  The provided power supply delivers safety extra low voltage corresponding to the input marking on the robot which is required to maintain safe operation.

• To prevent the risk of your robot falling downstairs, ensure that the charging station is placed at least 4 feet (1.2 meters) away from stairs.

• Do not allow liquids to get on or into the charging station

NOTICE

• Product may not be used with any type of power converter.
  Use of power converters will immediately void the warranty.

• If you live in an area prone to electrical storms, it is recommended that you use additional surge protection. Your charging station may be protected with a surge protector in the event of severe electrical storms.

BATTERY

WARNING

• Do not open, crush, heat above 176°F: 80°C, or incinerate.
  Follow the Owner’s Guide instructions for proper use, maintenance, handling, and disposal.

• Do not short-circuit the battery by allowing metal objects to contact battery terminals or immerse in liquid. Do not subject batteries to mechanical shock.

• Periodically inspect the battery pack for any sign of damage or leakage. Do not charge damaged or leaking battery packs, do not allow the liquid to come in contact with skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice. Place the battery in a sealed plastic bag and recycle or dispose of safely according to local environmental regulations, or return it to your local authorized iRobot Service Center for disposal.

CAUTION

• Battery usage by children should be supervised. Seek medical advice immediately if a cell or a battery has been swallowed.

NOTICE

• The battery pack must be removed from the robot before recycling or disposal.
• For best results, only use the iRobot Lithium Ion Battery that comes with the robot.
• Do not use non-rechargeable batteries. Use only the rechargeable battery supplied with the product. For replacement, purchase identical iRobot battery or contact iRobot Customer Care for alternative battery options.
• Always charge and remove the battery from your robot and accessories before long-term storage.

Note: For battery recycling go to call2recycle.org; or call 1-800-822-8837

About your Roomba® Robot Vacuum

• Top View
  

• Bottom View
  

• Home Base TM Charging Station
  

• Buttons & Indicators
  

Using Your Roomba® Robot Vacuum

Positioning the Home Base TM Charging Station

WARNING: To prevent the risk of your robot falling downstairs, ensure that the charging station is placed at least 4 feet (1.2 meters) away from stairs.

Charging

• Place the robot on the charging station to activate the battery.
  Note: Your robot comes with a partial charge, but we recommend that you charge the robot for 3 hours prior to starting the first cleaning job.

• If the “CLEAN” text is pulsing while charging, the robot is in the middle of a cleaning job and will automatically resume where it left off once recharged.

• The robot uses a small amount of power whenever it is on the charging station. You can put the robot in a further-reduced power state when not in use. For instructions and more details on this Reduced Power Standby Mode, refer to the iRobot Home App.

• For long-term storage, turn off the robot by removing it from the charging station and holding down for 10 seconds. Store the robot in a cool, dry place.

Cleaning

Remove excess clutter from floors before cleaning. Use your robot frequently to maintain well-conditioned floors.

• Your robot will automatically explore and clean your home.
  It will return to the charging station at the end of a cleaning job and whenever it needs to recharge.

• To send the robot back to its charging station, tap . A blue light ring pattern will indicate that the robot is seeking the charging station.

• When your robot detects an especially dirty area, it will engage Dirt Detect™ mode, moving in a forward/backward motion to clean the area more thoroughly. The light ring indicator will flash blue.

• Tap to spot clean a designated area. The robot will spiral outward about 3 feet (1 meter) and then spiral inward to end where it started. The light ring indicator will show a blue spiral.

When the robot senses its bin needs to be emptied, the light ring indicator will illuminate in a red sweeping motion toward the rear.

Troubleshooting

• Your robot will tell you something is wrong by playing an audio alert and turning the light ring indicator red. Press CLEAN or tap the bumper for details. Further support and instructional videos are available in the iRobot Home App.
  

• After 90 minutes of inactivity off the charging station, the robot will automatically end its cleaning job.

Battery Safety & Shipping

For best results, only use the iRobot Lithium Ion Battery that comes with your robot.

WARNING: Lithium ion batteries and products that contain lithium ion batteries are subject to stringent transportation regulations. If you need to ship this product for service, travel or any other reason, you MUST follow the below shipping instructions.

• Battery MUST be turned off before shipping.
• Turn off the battery by removing the robot from the charging station and holding down for 10 seconds. All indicators will turn off.
• Package the robot securely for shipping.
• If you need further assistance, contact our Customer Care team or visit global.irobot.com.

Accessories

Dual Mode Virtual Wall® Barrier

Note: For best results, place at least 8 feet (2.5 meters) from the charging station.

Use the Dual Mode Virtual Wall® barrier to keep the robot in the places you want cleaned — and out of the ones you don’t. It creates an invisible barrier that only the robot can see. You can leave the device in position between cleanings.

Dual Mode Virtual Wall included for select models only

Choose the mode to meet your needs:

Virtual Wall Mode: When the switch is in the Virtual Wall position ( ), the device will create a linear barrier to block openings up to 10 feet (3 meters).

Note: This barrier gets wider as it gets further from the device (refer to illustration).

Halo Mode: Toggle the switch to the Halo position ( ), to create a circular barrier. This will prevent the robot from approaching zones you want to protect such as a pet bowl, vase, or under a desk. The Halo barrier extends approximately 12 inches (30 centimeters) from the center of the device.

Note: The batteries will last about 8-10 months under normal use. If you are not planning to use your Virtual Wall barrier for an extended period of time, be sure to turn the switch to the Off, or middle position.

Care and Maintenance

Care and Maintenance Instructions

To keep your robot running at peak performance, perform the procedures on the following pages.

There are additional instructional videos in the iRobot Home App.

If you notice the robot picking up less debris from your floor, empty the bin, clean the filter and clean the brushes.

Every 2 months
Full Bin Sensor| Clean every 2 weeks|
Front Caster Wheel| Clean every 2 weeks| Every 12 months
Edge-Sweeping Brush and

Multi-Surface Brushes

| Clean once a month (twice a month if you have a pet)| Every 12 months
Sensors and Charging Contacts| Clean once a month|

Note: iRobot manufactures various replacement parts and assemblies. If you think you need a replacement part, please contact iRobot Customer Care for more information.

Replacement frequency may vary. Parts should be replaced if visible wear appears.

Emptying the Bin

1. Press bin release button to remove bin.
   

2. Open bin door to empty bin.
   

3. Place bin back in the robot.
   

Cleaning the Filter

1. Remove the bin. Remove the filter by grasping both ends and pulling out.
   

2. Remove debris by tapping the filter against your trash container.
   

3. Reinsert filter with ridged grips facing out. Place bin back in the robot.
   Important: The robot will not run if the filter is not installed correctly.
   Replace the filter every two months.

Cleaning the Full Bin Sensors

1. Remove and empty the bin.
   

2. Wipe the inner sensors with a clean, dry cloth.
   

3. Wipe the bin door with a clean, dry cloth.
   

Washing the Bin

Important: Do not wash the filter. Remove the filter before washing the bin.

1. Release the bin, remove the filter, and open the bin door.
2. Rinse the bin using warm water.

Note: Bin is not dishwasher safe.

3. Make sure bin is completely dry. Reinsert filter and place bin back in the robot.

Cleaning the Edge-Sweeping Brush

1. Use a coin or small screwdriver to remove the screw holding the Edge-Sweeping Brush in place.
2. Pull to remove the Edge-Sweeping Brush. Remove any hair or debris, then reinstall the brush.
   

Cleaning the Front Caster Wheel

1. Pull firmly on the front wheel module to remove it from the robot.
2. Pull firmly on the wheel to remove it from its housing (see illustration below).
3. Remove any debris from inside the wheel cavity.
4. Reinstall all parts when finished.
   Make sure the wheel clicks back into place.
   
   Important: A front wheel clogged with hair and debris could result in damage to your floor. If the wheel is not spinning freely after you have cleaned it, please contact Customer Care.

Cleaning the Multi-Surface Brushes

1. Pinch the brush frame release tab, lift the tab, and remove any obstructions.
   

2. Remove the brushes from the robot. Remove the brush caps from the ends of the brushes.
   Remove any hair or debris that has collected beneath the caps. Reinstall the brush caps.
   

3. Remove any hair or debris from the square and hexagonal pegs on the opposite side of the brushes.
   

4. Remove the bin from the robot and clear any debris from the vacuum path.
   

5. Reinstall the brushes in the robot.
   Match the shape of the brush pegs with the shape of the brush icons in the cleaning head module.
   

Cleaning the Sensors, Camera Window and Charging Contacts

1. Wipe sensors, camera window and charging contacts with a clean, dry cloth.
   
   Important: Do not spray cleaning solution or water onto the sensors or sensor openings.

iRobot Customer Care

USA & Canada

If you have questions or comments about your Roomba® robot vacuum, please contact iRobot before contacting a retailer.

You can start by visiting global.irobot.com for support tips, frequently asked questions and information about accessories. This information can also be found in the iRobot Home App. If you need further assistance, call our Customer Care team at 877-855-8593.

iRobot USA Customer Care Hours

• Monday to Friday, 9AM – 9PM Eastern Time
• Saturday and Sunday 9AM – 6PM Eastern Time

Outside USA & Canada

Visit global.irobot.com to:

• Learn more about iRobot in your country
• Get hints and tips to improve your Roomba® robot vacuum’s performance
• Get answers to questions
• Contact your local support center

Regulatory Information

FCC Supplier’s Declaration of Conformity

iRobot Corporation Roomba Model: RVB-Y2

Contains FCC ID: UFEAXE-Y1 and contains IC: 6652A-AXEY1

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device contains a license-exempt transmitter/receiver that complies with Innovation, Science and Economic Development (ISED) Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: 1) This device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device.

• Changes or modifications not expressly approved by iRobot
  Corporation could void the user’s authority to operate the equipment.
  • This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
  These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference to radio communication will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

• Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotopically radiated power (e.i.r.p.) is not more than the necessary for successful communication.

• FCC Radiation Exposure Statement: This product complies with FCC §2.1091(b) for mobile device RF exposure limits, set forth for an uncontrolled environment and is safe for the intended operation as described in this manual. Per FCC requirements, maintain a distance of more than 8 inches (20cm) between any person and the host device (Roomba robot).

• ISED Radiation Exposure Statement: This product complies with the Canadian Standard RSS-102 for portable RF exposure limits, set forth for an uncontrolled environment and is safe for the intended operation as described in this manual. Per ISED requirements, maintain a distance of more than 8 inches (20 cm) between any person and the robot. http://global.irobot.com

For battery recycling go to call2recycle.org; or call 1-800-822-8837

©2021 iRobot Corporation, 8 Crosby Drive, Bedford, MA 01730 USA. All rights reserved. iRobot, Roomba, iAdapt and Virtual Wall are registered trademarks of iRobot Corporation. Home Base and Dirt Detect are trademarks of iRobot Corporation. Wi-Fi and the Wi-Fi logo are registered trademarks of Wi-Fi Alliance.

FAQS

will it work in Europe, under 220V current (after applying a mechanical plug adapter)?

J7 without “+”(self cleaning station) will work at 220V.

How does it handle rugs with fringe?

If the fringe is long, it will get tangled up in it. If short, it does great!

Does the earlier style Virtual wall work with the I7?

The Roomba i7 is compatible with the Dual Mode Virtual Wall Barrier. That virtual wall is compatible with Roomba s, i, e, 900, 800, 700, 600 and 500 Series models.

Does it get stuck on thick rugs?

As long as the rugs do not have shag length nap or doesn’t have tassels it’ll work fine.

Is this this thing mapping your house and uploading it to a google server?

The Imprint Smart Map feature would create a map of your home. This information would be stored in the iRobot Cloud and not on a server like a Google Server.

Is the charger used voltage of this product 100-240 V?

This Robot is a US/Canadian model. Robots sold in the US and Canada come with the domestic charger which is rated at 120V and 60 Hz. We also make Robots for the International Market (outside of the US and Canada) that would come with the universal charger is rated at 120-240V and 50-60 Hz. These Robots would not be available for sale in the US.

Is the battery installed in the vacuum? Or do I have to install it myself?

The battery will be installed in the Robot already when it arrives. Simply unpack and set up the Robot on the Home Base and it will come out of shipping mode.

is this i7 the best room ba for 3 cats 1 dog 2 birds with carpets hardfloors and granite floor?

All of our Roomba vacuums work well on hard flooring and homes with pets. The i7 is one of the best that we offer. Please reach out to us at 1-800-727-9077, and we’ll find the best Roomba for your home.

does the iRobot Roombia have a light built in?

The only lights on the Robot would be the indicator lights on the Robot.

why does my i7+ only run for 19 mins and returns to base, i want it to clean longer?

Runtime cannot be set when using the Roomba i7+. Roomba will clean an entire level and return to the Clean Base once it has determined the area to be clean. If Roomba isn’t covering the entire floor plan, please contact support at 1-877-855-8593.

Does it have a charging station?

Yes, the Roomba i7 will come with a home base that charges the robot.

recently bought a I7 ( 07/2020) did not come with virtual box, is this normal now ?

It has to have a docking station which is connected to wifi.

The information says it connects with clean base, but there is no place to empty into the base unit?

The iRobot Roomba i7 does not come with the Automatic Dirt Disposal Clean Base. It comes with the standard Charging Dock. If you purchase the iRobot Roomba i7+ it will come with the Automatic Dirt Disposal Clean Base. If you purchase the iRobot Roomba i7, and then later on purchase the Automatic Dirt Disposal Clean Base separately, then the iRobot Roomba i7 will be able to connect to and work with the Automatic Dirt Disposal Clean Base.

Does the i7 have liquid sensors so it does not clean over pet vomit or spilled liquids?

No, the Roomba does not have liquid detecting sensors.

What is the difference between the i7 and Costco’s i8+?

The i8+ has a stronger battery and will have a slightly longer run time.

Does this shutdown in the dark?

The Roomba i7 is equipped with Dual Beam cliff sensors. These are an upgrade from the older model Roomba’s and are intended to help with darker surfaces or dimly lit areas.

Does this model have auto dirt disposal?

The i7 does not have Automatic Dirt Disposal, but is compatible with the Clean Base which can be purchased separately. It would be more cost effective to purchase the Roomba i7+ which will include the Robot and the Clean base in one package.

What is the height of the product?

Roomba’s are between 3.5 and 3.8 inches tall depending on the model, the Roomba i7 is 3.63 inches tall.

How does this work on thick shag rugs?

A Roomba vacuum works well on hard flooring and rugs. Please check the rug’s care tag or reach out to the manufacturer of the rug for recommended cleaning methods.

VIDEO

www.irobot.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>