Nakamichi NSA-CS1721 6.5 Inch 2-Way Component Speaker User Manual
- June 6, 2024
- Nakamichi
Table of Contents
Nakamichi NSA-CS1721 6.5 Inch 2-Way Component Speaker
nakamichicaraudio.com
nakamichi.global
nakamichi.caraudio
YOUR SPEAKER
Dear Customer,
Congratulations on purchasing our Nakamichi mobile system product for your
sound system.
This product has been designed and manufactured to Nakamichi’s exacting
standards to ensure many years of audio enjoyment. For the best performance,
we recommend that you have your Nakamichi product installed by an authorized
Nakamichi dealer.
If you would like to install this product on your own, we recommend for you to
go through this manual to familiarize yourself with all the installation
requirements and procedures.
If you encounter any issues or if you have any questions on the operation of
this product, please contact your nearest authorized Nakamichi dealer for
assistance, or you may also contact us through our website or social media
channels.
Installation of Your Product
In today’s modern vehicles, it is very easy to cause damage to existing
systems through improper installation. Please follow and scrutinize all wiring
diagrams to ensure that you have connected everything in its proper place.
If you find yourself uncomfortable of unfamiliar with understanding the wiring
and installation diagrams or testing instructions, do contact your nearest
Nakamichi dealer to perform the installation for you.
Safety Warnings and Considerations
- Clean only with a dry cloth or other similar materials.
- Install your product in a dry, well-ventilated location that does not interfere with your vehicle’s safety equipment.
- Do not block any ventilation openings when installing this product.
- Do not mount the product in the engine compartment of your vehicle or in any areas of extreme heat such as mufflers, silencers, exhaust pipes or other heat-producing apparatus.
DIMENSIONS (UNIT: MM)
SPECIFICATIONS
- Speaker Type: 6.5″ (16.5 cm) 2-way
- Mounting Depth: 2.4″ (63 mm)
- N-power: 70 watts
- Peak Power: 460 watts
- Sensitivity(Db/w/m): 90 ± 3 dB
- Frequency Response: 53-19.5k Hz
- Impedance: 40
- Voice Coil: KSV cD25.5 mm
- Magnet Mass: 12.1 Oz (376 g)
- Net Mass ( 1 set): Approx. 2.3 kg
WHAT’S IN THE BOX
Check and identify the contents of your package:
- Wooferxl pr
- Crossover xl pr
- Tweeterxlpr
- Angle Adapter xl pr
- 04 x 25 mm Screwxl2pcs
- Tweeter Mounting Base x2pcs
- Tweeter Mesh Grille Blackx2pcs
- User Manual xl pc
- Self-adhesive EV Ax 2pcs
- Hexagonal Wrench x l pc
- Gasketsx l2pcs
- Speaker Sealing Tape x 1 pc
- (Grille Net+ Frame) x2sets
INSTALLATION
Option 1: Mount the woofer on door (front or rear)
You can mount the woofers on the front/rear door of your car.
- Make sure that nothing obstructs around the mounting location of the door.
- A hole for mounting may already be cut out of the inner panel of the door(front or rear). In this care, you need to modify the board only.
- Ensure that the speaker terminals, frame or magnet do not interfere with any inner parts, such as the window), etc. Also ensure that the speaker grille does not touch any inner fittings, such as the window cranks, door handles, arm
-
Turn off the car ignition key.
If the power is on, the click noise generated by the connection may damage the speakers. -
Cut out the mounting template from the packing box.
-
Pas te the template on the location selected for mounting the speaker.
-
Mark the cut-off hole and the 8 bolt holes. (Fig. l)
-
Cut out the marked area and drill the bolt holes. (Fig.2)
-
Remove the grille net. (Fig.3)
-
Connect the woofers to the network or car audio.
(See How to complete the wiring.) -
Mount on the speaker as shown below. (Fig.4)
-
Press and insert the edges of the grille net.
The speaker grille can be mounted without the grille net, if you like.
Option 2: Mount the woofer on rear tray
You can also mount the speakers into the surface of the rear tray.
Follow the steps in section “Option 1: Mount on door” to mount the speakers
into the rear tray.
Mount the Tweeter
Mount the Network
- Find a proper location to mount the networks.
- Mount the networks onto the car with the supplied screws.
HOW TO COMPLETE THE WIRING.
Connect the woofers and the tweeters to the 2-way crossover network first, then connect the network to your amplifier or car audio directly.
- Consult the diagram below. Be sure to connect corresponding terminals, i.e.”+” to”+” and”-” to”-“. Connection with reversed polarity will degrade the quality of production.
- Connect the provided speaker cord to the speaker terminal while holding the lower portion of the speaker terminal.
NSA-CS1721
SCAN OUR QR CODE OR VISIT
WWW.NAKAMICHICARAUDIO.COM
FOR COMPLETE AUDIO SETTINGS INSTRUCTIONS
nakamichi.global
nakamichi.caraudio
Made in China