AVEROS CoreBlu X3 Indoor Positioning and Navigation User Manual
- June 6, 2024
- AVEROS
Table of Contents
AVEROS CoreBlu X3 Indoor Positioning and Navigation
Introduction:
The CoreBlu line is a series of advanced Bluetooth Low Energy 5.x beacon devices using mul standard beacon technology.The CoreBlu-X3 is specially conceived for advanced business solu on using local on based and indoor navigate on based applica on. It features an ultra-low power consume on and long ba very life. The CoreBlu-X3 can be easily mounted on various surfaces and uses commercially available replaceable large capacity baseries.The CoreBlu-X3 comes with a downloadable SDK with an extensive library for easy Integra on into a wide range of local on-based and indoor navigate on-based applications. It also includes a wide range of tools facilita ng op mal setup, installed on and health-checks.
Physical characteristics:
Usage:
- CoreBlu X3 is designed to be mounted anywhere on various surfaces with the help of double-sided tape or screws to be detected by nearby smartphones.
- CoreBlu X3 is mainly used in indoor navigate on applications.
- CoreBlu X3 also includes a wide range of tools facilita ng op mal setup, installed on and health-checks.
- Long buon presses allow the beacons to restart/wake up (if sleeping) and show India on in the front LED.
Features:
-
Bluetooth Radio
Type: Bluetooth: Low energy 5.0
Advert segment: iBeacon, Eddystone & beacon (Averos Proprietary).
Advert cement Interval: 100ms to 10.2seconds.
Frequency: 2.4GHz.
Transmit Power: +4dBm to -20 dBm.
Antenna Type: PCB antenna, Omni Directcanal. -
Sensor
Mo on sensing: 3 Axis Accelerometer. -
Baery
Battery type: ER14505 x 2, 4800mAh, Replaceable. -
Enclosure
Material: ABS.
Protec on Class: IP64. -
Opera ng Environment
Temperature Range -20°C to 70°C.
Opera ng Humidity 90%. -
User interface
User interface buon.
User indica on the LED.
Quick Start:
After unpacking the CoreBlu X3, we have the following steps to check the
device quickly.
-
Hardware Test
Press the button for 5 sec and observe the LED blinking in front of CoreBlu X3. The device will now wake up from sleep mode. -
Sofware Test
CoreBlu X3 has a Serial QRCode printed on the side, which maps to the Beacon MAC address. To verify the CoreBlu X3 is transmitng packets we have to scan the Barcode via Beacon Manager application. Once Beacon Manager has been installed in the smartphone, select iBeacons. After that click, the no filter selected button top let of the screen then click QR Code button, scan the QRCode on CoreBlu X3 and press apply, if CoreBlu X3 is turned on it will show on the list on the screen.
Configura on Setting:
Please refer to the configura on guide.
Warning:
CoreBlu X3 contains electronic elements and a battery which should be properly
disposed of. If a beacon needs to be disposed of, please contact the
manufacturer’s technical support first.
FCC Cautions:
This device complies with part 15 of the applicable FCC Rules. Its opera on is
subject to the following two condition: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired opera on. Any changes or
modifica ons not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protect on against harmful interference in a
residensal installed on. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with The
instructions may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a par cular
installed on. If this equipment does cause harmful interference to radio or
television Recep on, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separate on between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure Condi on without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>