Hisense MW505 TV WiFi Bluetooth Module User Manual
- June 6, 2024
- Hisense
Table of Contents
Hisense MW505 TV WiFi Bluetooth Module
The product description
The user can achieve TV connection WIFI net and Bluetooth, through this module
This equipment may be operated in all European countries.
Basic parameters
| Feature Description | Feature Description |
|---|---|
| Model | MW505 |
| Product Name | WiFi 11a/b/g/n 2T2R and BT5.0 Model |
| Major Chipset | MTK7638BU |
| WLAN Standard | IEEE 802.11a/b/g/n |
| BT Standard | BT2.1/3.0/4.0/5.0 |
| WLAN Frequency Range | 2.4GHz~2.4835GHz,5.15~5.85GHz |
| BT Frequency Range | 2402MHz~2480MHz |
Spread Spectrum
| IEEE 802.11b: DSSS (Direct Sequence Spread Spectrum)
IEEE802.11a/g/n/ac: OFDM (Orthogonal Frequency Division Multiplexing)
Modulation Method| DSSS/DBPSK/DQPSK/16-QAM/ 64-QAM/256QAM
Data Transfer Rate| 1,2,5.5,6,11,12,18,22,24,30,36,48,54,60, 90,120 and
maximum of
867Mbps
Antenna Reference| WIFI1/BT Internal Printed ANT,WIFI external ANT
Interface| USB2.0
Supply Voltage| 3.3V±0.2V
Dimension| 45（mm）30（mm）2.85（mm）
Operating Temperature| -10°C to 70°C
Storage Temperature| -40°C to 85°C
RF output power
| Banda | Limited power | |
|---|---|---|
| BT | 2402MHZ-2480MHZ | 0-20 |
| WlAN | 2412MHZ-2472MHZ | <20 |
5150MHZ-5850MHZ
The display method of Model approved code
In the factory the model approve code is pasted on the back shell in a label.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver. -
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of FCC RF Rules. This equipment should be installed and operated with minimum distance of 20 in (50cm)between the radiator and your body. This transmitter must not be co- located or operated in conjunction with any other antenna or transmitter
CAUTION:
To comply with the limits of the Class B digital device pursuant to Part 15 of
the FCC Rules, this device is compliant with Class B limits. All peripherals
must be shielded and grounded. Operation with non-certified peripherals or
non-shielded cables may results in interference to radio or reception
MODIFICATION
To assure continued compliance, Any changes or modifications not expressly
approved by the grantee of this device could void the users authority to
operate the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 50 cm(8 in )between the radiator and your body NOTE To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product Contains Transmitter module FCC ID: *** To satisfy IESD exterior labeling requirements, the following text must be placed on the exterior of the end product ” Contains Transmitter module IC:
This symbol on the product or on its packaging indicates that this product
must not be disposed of with your household waste. Instead, it is your
responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and
electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources and
ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste
equipment for recycling, please contact your local city office, your household
waste disposal service or the shop where you purchased the product.
The device is restricted to indoor use only when operating in the 5150 to 5350
MHz frequency range.
Manufacturer: QingdaoHisense Communication Co., Ltd.
Address: 218 Qianwangang Road, Qingdao Economic & Technological Development
Zone, Qingdao, China
Importers:
Hisense France SAS
Address: 9 Rue des 3 Soeurs, 93420 Villepinte, France
Hisense Iberia, S.L.U
Address: Ronda Auguste y Louis Lumiere. 23 Nave 12. Edificio Lumiere – Parque
Tecnológico 46980
Paterna (Valencia) – Spain
Hisense Italia S.r.l
Address: Via Montefeltro, 6/A, 20156 MILANO
Hisense South Africa
Address: The Estuaries, Building 17 Oxbow Crescent, Century City, Cape Town,
SouthAfrica