DS18 NXL-10SUB Marine Water Resistant Subwoofer Owner’s Manual

OWNER’S MANUAL
NXL-10sub
CF-10sub
10″ MARINE GRADE SUBWOOFER WITH
STAINLESS STEEL MESH AND RGB LED LIGHTS

FEATURES

• 10″ Subwoofer for Marine & Motorsports
• Continuous Power Handling 300W RMS
• Peak Music Power 600W MAX
• Sensitivity: 89dB at 1W/1M
• Nominal Impedance: 4 Ohm
• IP65 Marine Grade Compliant Specifications, 100% UV Stable
• Motor Structure Use Y35 Ferrite Main Magnet
• Injection Molded Polypropylene Cone with UV Protection and Butyl Surround
• Grill with Injection Molded Composite with 316 Stainless Steel mesh
• Integrated RGB LED Lighting
• LED Controller with Smartphone App Available. For Multi-Function RGB LED Lighting option (Sold Separately)

PACKING INCLUDES

• 1 X 10” Subwoofer for Marine & Motorsport
• 1 X 1.5M #18 Speaker Input Wires With Fast Terminal
• 1 X 1.5M #22 RGB LED Power Input Wires With Fast Terminal
• 6 X M5.2 Philips Inner Hex Head 304 Stainless Screw (4mm Hex Tool)
• 1 X Owner’s Manual

READ BEFORE INSTALLATION

1. Be sure to carefully read and understand the instructions before attempting to install these speakers.

2. For safety, disconnect the negative battery terminal from the battery prior to beginning the installation.

3. For easier assembly, we suggest you run all wires prior to mouinting speakers in place.

4. Use high quality connectors for a reliable installation and to minimize signal or power loss.

5. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any
   vehicle. If installation in a boat, take care not to cut or drill through the main hull.

6. Never run wires underneath the vehicle. Running the wires inside the vehicle or hull area provides the best protection.

7. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall.

INSTALLATION

Determine where the speakers will be mounted. Ensure an area large enough for the speaker to mount evenly. Be sure that the mounting location is deep
enough for the speaker to fit; only mount to a flat surface. Use extra caution when mounting on panels with urethane foam.

1. Refer to the specification chart to determine the proper diameter hole to cut for your speakers.
2. Mark the locations for the mounting screws. Drill the holes with a 0.157” bit.
3. Feed the speaker wires through the cutout and connect to the speaker terminals. Be sure to observe proper polarity when connecting the wires. The speaker’s positive terminal is indicated with a”+”.
4. Fit the speaker and mount it into place using six (6) screws.
5. Tighten the screws until the speaker is snug in place

LED CONNECTIONS: There are two options to choose from:

WIRING

1. lf you have an LED Control Module (LED-BTC), Connect as shown in the Following diagram:

2. To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:

3. Green Color: “G” Fast Terminal Connect to Battery Negative

4. Red Color: “R’ Fast Terminal Connect to Battery Negative

5. Blue Color: “B” Fast Terminal Connect to Battery Negative

6. Purple Color: “R” And “B” Fast Terminal Connect to Battery Negative

7. Yellow Color: “R’ And “G’ Fast Terminal Connect to Battery Negative

8. Cyan Color: “B” And “G” Fast Terminal Connect to Battery Negative

9. While Color:”R’ And ‘B’ And “G’ Fast Terminal Connect to Battery Negative

EXAMPLE OF GREEN LIGHT CONNECTION:

SPECIFICATIONS

GENERAL SPECIFICATIONS
Nominal Diameter………………………………………………………….10″ / 254mm
Nominal Impedance……………………………………………………… 4 Ohm
RMS Power Handling……………………………………………………. 300W
MAX Power Handling………………………………………………….. 600W
Sensitivity (1w/1m)………………………………………………………. 89dB
Frequency Response………………………………………………………35-250Hz
Recommended Low Pass Crossover…………………………….. 100Hz
Sealed Internal Volume………………………………………………….0.6~2ft3

BODY – FEATURES
UV Compliant…………………………………………………………….. Yes, 100% Stable
Marine Grade Type…………………………………………………….. IP65
RGB LED………………………………………………………………….. Yes, RGB integrated
Grill Type…………………………………………………………………….Injection Molded Composite with 316 Stainless Steel mesh
Sold as Single……………………………………………………………… Yes

WOOFER SPECIFICATIONS

Voice Coil Diameter………………………………………… 2″ / 50.8mm
Voice Coil Former Material………………………………Glass Fiber
Winding Material…………………………………………….. CCAW
Cone Material …………………………………………………. Injection Molded Polypropylene + UV Compliant
Surround Material……………………………………………. Butyl (Rubber)
Basket Material……………………………………………….. High Temp Injection Molded Composite with UV Protection coating
Magnet Material……………………………………………….Ferrite
Magnet Weight……………………………………………….. 72 oz

THIELE & SMALL PARAMETERS
Equivalent Volume………………………. Vas ………………………..26.7L / 0.94ft3
Excursion (one way)……………………. Xmax ……………………. 13mm
Free Air Resonance……………………… Fs ………………………….45Hz
Mechanical Factor……………………….. Qms……………………….8.919
Electrical Factor………………………….. Qes ……………………….0.805
Total Factor…………………………………. Qts…………………………0.457
Moving Mass……………………………….. Mms ……………………. 73.229g
Compliance………………………………… Cms ………………………0.171 mm/N
Bl Factor……………………………………… Bl …. …………………….9.68
Voice Coil Inductance…………………. Le………………………….1.8418mH
Diaphragm Area…………………………. Sd ………………………. 333.29 Cm3
DC Resistance……………………………. Re ………………………… 3.65 ohm
Efficiency Bandwidth Product….. EBP………………………..55.9

RECOMMENDED ENCLOSURES
Sealed Internal Volume………………………………………0.6~2ft3
Sealed Box Output ResponseF3 ………………………..64~45Hz
Free Air or Baffle Mount………………………………….. Yes recommended

MEASUREMENT
Overall Diameter……………………………………………… 10.76″ / 273.3mm
Overall Depth……………………………………………………6.73″ / 171mm
Front Mount Baffle Cutout……………………………….8.78″ / 223mm
Mounting Depth………………………………………………. 5″ / 127.5mm
Motor Diameter………………………………………………..5.51″ / 140mm

COLOR AVAILABLE
Black Satin……………………………………………………. NXL-10SUB/BK
White Gloss……………………………………………………NXL-10SUB/WH
Carbo Fiber Texture Gloss…………………………… CF-1OSUB

WARRANTY

Should your NXL-10SUB or CF-10SUB require service please consult with the dealer from which it was purchased, or contact DS18 local dealer. Do not attempt to return your subwoofer directly to us without first calling for a Return Authorization Number. Units received without an accompanying
Return Authorization Number will be processed more slowly. Additionally, your must include a copy of your purchase receipt from an authorized dealer for consideration of in-warranty service; otherwise repair charges will apply. Units received without a receipt will be held for 30 days, allowing us time to contact you and obtain a copy of the receipt. After 30 days, all units will be returned.

MEASUREMENTS

NXL-10sub
CF-10sub

We reserve the right to change products and specifications at any time without notice.
Images may or may not included optional equipment.

FOR MORE INFORMATION
PLEASE VISIT DS18.COM

WE LIKE IT LOUD

Documents / Resources

| DS18 NXL-10SUB Marine Water Resistant Subwoofer [pdf] Owner's Manual
NXL-10SUB, Marine Water Resistant Subwoofer, NXL-10SUB Marine Water Resistant Subwoofer, Water Resistant Subwoofer, Resistant Subwoofer, Subwoofer
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>