FlyPie 6K Pro Drone User Manual

Flypie
6K PRO
User Manual

Safety Guidelines

Thank you for choosing Flypie Drone! This manual handbook will guide you to start your safe drone flight. For your safety, please read and get ready properly before flying, and preserve this handbook properly for future reference requirements.

• By the provisions of Law, Flypie Drone MUST be registered and get the flight application before takeoff in the territory of the People’s Republic of China.
• Please DO the safety check every single time before takeoff. Make sure there is no any damage of all parts of drone. Fly safelly and carefully to avoid the accident such as crash, secondary damage and injury.
• By the provisions of Law, DO NOT fly at altitude above 400 feets (120m) in the territory of the People’s Republic of China.(Over 120 meters,need to file with the local competent authority.)
• DO NOT fly near the no fly zones such as: airports, international borders, military area, government apparatus area etc.
• DO NOT fly indoors. Please always fly at the open environment avoiding crowds, animals, buildings, trees, waters or any other interferences.
• DO NOT take off while the bad weather conditions. Severe weather conditions could damege the drone.
• DO NOT turn on the drone for a long time to avoid overheating of the components and shorten the service life of the drone.
• Please beware of the strong electromagnetic sources such as communication base station, transformer substation, high power antenna. The signal interference may cause the disconnection. Please always fly within visual of your sight to avoid the accident of the wrong judgement of flying control. Please beware of the transmission signal and transmiting image is fully clear. If the transmission is too dark, not clear or stablly transmiting, please fly return immediately to avoid any accident. Please check and follow the instractions of the local laws and regulations before you takeoff. Have a good flight!

Learn About Flypie Drone

Drone

Ready to Fly

Devices Charge:
Charge Drone battery by using dedicated charger, charge drone controller by using MicroaLISB cable. The power Lights will keep blinking while charging until the lights all go out means charging is complete.

Install battery :
Turn the drone upside down then insert the battery into the battery slot. Push the battery locker to the direction of the 8 lock sign on both sides.

Mounting Propellers :
The propeller is marked as A/B pairs on the propellers’ blade-faces which correspond to A/B motors. Choose the appropriate propeller, mount it into the motor slot that corresponds fitly. Press down and turn to the end of the slot then let go, the propeller will be locked by its tenon.

Safety Confirmation :
Make sure the arms of the drone and the propellers’ blades are all unfolded completely as shown as the figure down below. Confirm propellers have been locked in motors’ slots, Confirm the battery lock has locked the battery firmly.

Prepare for Take-Off

Please scan the following QR code to download and install the FLYPIE APP. The FLYPIE APP must be installed and connected to activate the drone.

Press Power Buttons once to check the battery level. Please make sure all the battery is fully charged

Battery Power Botton : Short press once to check the battery level, Long press for -1 second to turn on.
Drone will be self-check after turned on, the flight lights of the back arms will be blinking by red, yellow and green alternately until checked finished.

Controller Power Botton: Short press once to check the battery level, Long press for -1 second to turn on.
The power light will be blinking by red while searching for the drone’s connection, the light will turn green when the drone is connected.

Connect to Flypie APP

Use phone number to register and log in. Turn on the WIFI of your device and enter the list of the WIFI networks. Serch the drone control WIFI network which begin with FP and connects to it. CODE: 87654321. Back to the FLYPIE APP after connecting. Follow the instructions of the APP until the main button turns to green. Press the green button to ENTER CAMERA.

Drone will automaticly serch GPS signal, and the flight lights on back arms will blink by yellow when enter the camera interface. The lights will turn to green when the sureching is compelet and the APP will shows READY TO GO. By now, you are ready to take off !

Take-Off Guide

Please make sure the Switch Nose Button and the Flight Modes Button is at the up-side position. Push both of the button up to DEFAULT NOSE and POSITIONING MODE.
Pull down would be REVERSE NOSE and INDOOR ALTITUDE MODE, may pose risk of misoperation.

Manual Take-off : Push both sticks to the inner bottom corners to start the motors. Once the motors have started spinning, release both sticks simultaneously
Push left stick up slowly and steadily, drone will take off. Relesase the stick, drone will automatic hover.

Toggle gimbal thumbwheel can be able to adjust camera pitch angle. Shot button can be able to Take picture or Film video. Two modes can be switched on Flypie APP.

Fly Guide

In Default Nose mode, the gimbal camera side is nose, battery side is tail.
Under normal conditions, there are Red and Green flight lights under drone arms. The arms with Red lights are the Default Nose Front Arms, with Green lights are Default Nose Back Arms.
Flight lights can be use to observe drone’s toward and use to judge drone status.

Landing Guide

Manual Landing : 1) Pull the leftstick down stadily to descent altitude. 2) Keep pulling the leftstick down to the bottom for 3 seconds to stop the motors after drone lands on the ground. 3) Long press the battery and controller power button until) the power lights off to turn off the drone and controller.

One Button Take-Off & Landing: When the drone stops, Long press the Take-Off & Landing Button for 1 second, drone will take off and ascent up to 3 meters and hover. When the drone in the air, Long press Take-Off & Landing Button lo for 1 second, drone will descent to land and stop motors automatically.

To Takeover, Long Press Take-Off & Landing Button again to cancel while auto take-off or landing is progressing. Push or Pull the left stick on the controller can also be able to cancel the auto take-off or landing, drone will stop the automatic altitude changing progress.

Intellectual Functions

One Button Return : Long press Take-Off & Landing Button ® for 1 second, there will be prompt sound and red light in the button to remind activated, and Flypie App will shows confirmation popup window. Tap the Take-Off & Landing Button in Flypie App can also implement the same functionality. After confirm, drone will ascent up to preset autitude (set in app) than fly straight back and automaticly land.
Tap the button in App again or operat the sticks on the controler to cancle return and take over, Use the button on controler only can be cancled by long press the button again until the red light off. Switch Nose : Pull down the switch will Reverse Nose, the horizontal direction will be opposite. Flight Modes : P mode is Positioning Mode, all positioning system will be normal operating. A mode is Altitude Mode, only use to the increase hover stability in weak light and low fly altitude environment. Intelligent Following : Make sure the Flight Mode is P-Mode. Activate the Intelligent Following in the App and set a distance, drone will follow operater and maintain the relative distance which been set, drone nose will maintain following operater. Please make sure the GPS signal of drone and mobile device both are sufficient. Tap the Stop button in app or operat the remote controler stick to stop the function and take over control.
VR Panorama : Fly the drone to the centre of the scenery, activate the VR Panorama in app then drone will take VR pictures automaticity by easy-one-tap Start. Motion-lapse Video : Active the Motion-lapse video in app, set the direction and constant fly speed then start. The flying control , video frame pictures shooting and the video post compositing all can be automatically done. Target Circumferential Flying : Activate the Target Circumferential in app. Fly the drone above the target, set the target point in app and set the circle around flying speed, fly to a circle around disctance and tap start. While the automatic circumferential flying you could also adjust the flying speed, autitude, and the disctance to target. Way Point Mode : Activate the Way Point Mode in app, set the way points in the map, the drone will auto fly on the way. Wide Angle Mode : Activate the wide angle mode in app can be able to take 180° wide angle picture.

Identification

Drone Flight Light Status (The lights on front arms always remain red)

Remote Controller Button

Maintenance and Calibration

1. Propellers The propeller is easy-damaged parts. Please pay attention to any worn of the propeller and change the damaged propeller.
2. Battery DO NOT throw the battery into the fire. DO NOT hit the battery violently. The performance would be reduced a low-temperature environment.
3. Compass Calibration The compass needs to be recalibrated to ensure flight safety when the magnetic field interference. The notice and guide will be shown on App If the drone needs calibration.

Compass Calibration

Start Calibration

Specification

After-sales Policies

Flypie Guarantee Instruction
According to Law of the PRC on the Protection of the Rights and Interests of Consumers, Law of the People’s Republic of China on Product Quality, Flypie after-sales service policies are as follows:

1. Within 7 days after you receive, if the product has performance malfunction, performance manufacturing defect, or shipment damage, the product can be returned or replaced for free after fly pie official examined qualified.
2. Within 8-15 days after you receive, if the product has performance malfunction, performance manufacturing defect, or shipment damage, the product can be replaced or repaired for free after fly pie official examined qualified.
3. Within the product warranty period, if the product has a performance malfunction, performance manufacturing defect, the product can be repaired for free after fly pie official examined qualified

Product Performance Fault List

| Performance Failure
---|---
Flypie Drone| Drone Fault
Remote controller Fault
Battery Fault
Charger Fault
Significant manufacturing defects were found before use

Product Warranty Period

Non Warranty Regulations

1. Any product fault or damage has been caused by unauthorized modification or man-made damage.
2. Any damage has been caused by force majeure.
3. The guarantee has been expired.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>