OTTOLIVES BL-XK01 Music Starry Sky Projection Lamp User Guide

OTTOLIVES BL-XK01 Music Starry Sky Projection Lamp

Unboxing Check

Thank you for purchasing our products, please read the instruction manual carefully before use. The instruction manual contains necessary safety advice and user instructions, follow the instruction manual to operate in order to avoid damaging the product for misuse. Check whether the product is damaged or not when you receive the product.

Package list:

• Music starry projector x 1
• Remote controller x 1
• USB cable x 1
• User manual x1

Warnings:
The power requirement of this product is USB DC 5V/2A. Once the range exceeded, please use the regulator device, otherwise it’ II affect its service life.

NOTICE:

1. Strictly in accordance with the instructions of this operation, do not disassemble the host and accessories.
2. This product is suitable for indoor use.
3. The product is projected by LED and laser combinations, please do not use laser shone directly in eyes and keep away from children.

How to use:

1. Indoor use, projecting in the sky direction.
2. How to use the light projector, as shown below.
3. Connect Bluetooth “BTK10” of the smartphone to play music.
4. Use the correct method of the remote control to make sure the remote control is pointing at the infrared sensor.

Host button function description

1. Automatic recognition USB data. Note that this projector can auto recognize and play music while inserting USS memory. USS should contain some songs

2. Ocean wave 3 levels brightness adjustment

3. When Power on, LED light and laser light keep on; short press this key control LED light switch, long press control laser light switch

4. DC Input: 5V/2A

5. Short press play previous song; long press reduce the volume

6. Short press play next song; Long press increases volume

7. Short press control music Play/Pause; Long press change USS to Bluetooth ( Connect Bluetooth and U-Disk at same time, it’ll recognize U-Disk music for priority)

8. Short press achieve Bluetooth/USB mode switch when connecting Bluetooth and
   USB at the same time

9. Power ON/OFF

Statement

This product has been compre_hensive _and rigorous tested at the facto~y. t~e user should strictly follow the warning and instructions. Improper use resulting m product damage is not covered by the Company’s warranty. Remote control function description

Instruction:

When projector light connects power; LED blue light keeps on and in non-moved status; laser light enters gradation mode, it can default automatically switch off m 4 hours

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Statement
To maintain compliance with FCC’s RF exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm the radiator your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>