kaden KSI Series Wall Mounted Air Conditioner Remote Control User Manual
- June 6, 2024
- kaden
Table of Contents
KSI Series Wall Mounted Air Conditioner Remote Control
User Manual
KSI SERIES
KSI06 | KSI09 | KSI12
KSI18 | KSI24 | KSI28
Important note
Read this manual carefully before installing or operating your new air
conditioning unit. Make sure to save this manual for future reference.
Remote controller specifications
| RG66A1/BGEF
---|---
Rated voltage| 3.0V (dry batteries R03/LR03×2)
Signal receiving range| 8m
Environment| -5ºC~60ºC
Function buttons
Before you begin using your new air conditioner, make sure to familiarise yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to use the basic/advanced functions section of this manual.
Handling the remote controller
Not sure what a function does?
Refer to the How to use basic functions and How to use advanced functions
sections of this manual for a detailed description of how to use your air
conditioner.
Inserting and replacing batteries
Your air conditioning unit comes with two AAA batteries. Put the batteries in
the remote control before use:
- Remove the back cover from the remote control, exposing the battery compartment.
- Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
- Install the back cover.
Tips for using the remote control
- The remote control must be used within 8 meters of the unit.
- The unit will beep when a remote signal is received.
- Curtains, other materials, and direct sunlight can interfere with the infrared signal receiver.
- Remove batteries if the remote control will not be used for more than 2 months.
Installing remote control holder
The remote controller can be attached to a wall or stand by using a remote
controller holder.
- Before installing the remote controller, check that the air conditioner receives the signals properly.
- Install the holder with two screws.
- Put the remote controller in the holder.
Battery notes
For optimum product performance:
- Do not mix old and new batteries or batteries of different types.
- Do not leave batteries in the remote control if you don’t plan on using the device for more than 2 months.
Battery disposal
Do not dispose of batteries as unsorted municipal waste. Refer to local laws
for proper disposal of batteries.
Remote LCD screen indicators
Information is displayed when the remote controller is powered up.
NOTE: All indicators shown in the figure are for the purpose of clear
presentation. But during the actual operation, only the relative function
signs are shown on the display window. Note:
All indicators shown in the figure are for the purpose of clear presentation.
But during actual operation, only the relative function signs are shown on the
display window.
How to use the basic functions
AUTO operation
In AUTO mode, the unit will automatically select the COOL, FAN, HEAT or DRY
mode based on the set temperature.
- Press the MODE button to select AUTO mode.
- Set your desired temperature using the Temp + or Temp – button.
- Press the ON/OFF button to start the unit.
NOTE: FAN SPEED can’t be set in Auto mode.
COOL or HEAT operation
- Press the MODE button to select COOL mode.
- Set your desired temperature using the Temp + or Temp – button.
- Press the FAN button to select the fan speed.
- Press the ON/OFF button to start the unit.
Setting temperature
The operating temperature range for units is 17ºC – 30ºC. You can increase or
decrease the set temperature in 1ºC increments.
DRY operation (dehumidifying)
- Press the MODE button to select DRY mode.
- Set your desired temperature using the Temp + or Temp – button.
- Press the ON/OFF button to start the unit.
NOTE: FAN SPEED can’t be changed in DRY mode.
FAN operation
- Press the MODE button to select FAN mode.
- Press the FAN button to select the fan speed.
- Press the ON/OFF button to start the unit.
NOTE: You can’t set the temperature in FAN mode. As a result, your remote
control’s LCD screen will not display temperature.
Setting the TIMER function
Your air conditioning unit has two timer-related functions:
• TIMER ON – sets the amount of time after which the unit will automatically
turn on.
• TIMER OFF – sets the amount of time after which the unit will automatically
turn off.
TIMER ON function
The TIMER ON function allows you to set a period of time after which the unit
will automatically turn on, such as when you come home from work.
-
Press the Timer button, the Timer on the indicator “ “ displays and flashes. By default, the last time period that you set and an “h” (indicating hours) will appear on
the display. -
Note: This number indicates the amount of time after the current time that you want the unit to turn on. For example, if you set TIMER ON for 2.5 hours, “2.5h“ will appear on the screen, and the unit will turn on after 2.5 hours.
-
Press the Temp + or Temp – button repeatedly to set the time when you want the unit to turn on.
-
Wait 3 seconds, then the TIMER ON function will be activated. The digital display on your remote control will then return to the temperature display. The “ “ indicator remains on and this function is activated.
TIMER OFF function
The TIMER off function allows you to set a period of time after which the unit
will automatically turn off, such as when you wake up.
- Press the Timer button, the Timer off indicator“ “ displays and flashes. By default, the last time period that you set and an “ ” (indicating hours) will appear on the display.
- Note: This number indicates the amount of time after the current time that you want the unit to turn off. For example, if you set TIMER OFF for 5 hours, “5.0h“ will appear on the screen, and the unit will turn off after 5 hours.
- Press the Temp + or Temp – button repeatedly to set the time when you want the unit to turn off.
- Wait 3 seconds, then the TIMER OFF function will be activated. The digital display on your remote control will then return to the temperature display. The “ “ indicator remains on and this function is activated.
NOTE: When setting the TIMER ON or TIMER OFF functions, up to 10 hours,
the time will increase in 30-minute increments with each press. After 10 hours
and up to 24, it will increase in 1-hour increments. The timer will revert to
zero after 24 hours. You can turn off either function by setting its timer to
“0.0h” ON/OFF MODE SHORT CUT
TEMP TIMER ON
Setting both TIMER ON and TIMER OFF at the same time
Keep in mind that the time periods you set for both functions refer to hours
after the current time. For example, say that the current time is 1:00 PM, and
you want the unit to turn on automatically at 7:00 PM. You want it to operate
for 2 hours, then automatically turn off at 9:00 PM.
Do the following:
Example: Setting the unit to turn on after 6 hours, operate for 2 hours, then
turn off (see figure below).
Your remote display:
How to use the advanced functions
ECO function
ECO/GEAR function (some units)
Press the X-ECO button to enter the energy-efficient mode in a sequence of the
following: ECO ➞ GEAR (75%) ➞ GEAR (50%) ➞ Previous setting mode ➞ ECO… Note:
This function is only available under COOL mode.
NOTE: This function is only available under COOL mode.
ECO operation
When the ECO feature is activated, the air conditioner will operate
automatically at 24ºC. The fan speed is Auto.
NOTE: Pressing the ON/OFF button, modifying the mode or adjusting the set
temperature to less than 24ºC will stop ECO operation.
Under ECO operation, the set temperature should be 24ºC or higher. It may
result in insufficient cooling if you feel unconformable, just adjust the
temperature to stop it.
NOTE: The SLEEP function is not available in FAN or DRY mode.
SLEEP function
The SLEEP function is used to decrease energy use while you sleep (and don’t
need the same temperature settings to stay comfortable). This function can
only be activated
via remote control. For detail, see “sleep operation” in OWNER’S MANUAL.
TURBO function
The TURBO function makes the unit work extra hard to reach your present
temperature in the shortest amount of time possible.
- When you select the TURBO feature in COOL/HEAT mode, the unit will blow cool/hot air with the strongest wind setting to jump-start the cooling/heating process.
ACTIVE CLEAN function
-
The Active clean technology washes away dust, mold, and grease that may cause odors when it adheres to the heat exchanger by automatically freezing and then rapidly thawing the frost. A “pi-pi” sound will be heard.
-
The ACTIVE CLEAN operation is used to produce more condensed water to improve the cleaning effect, and the cold air will blow out. After cleaning, the internal wind
the wheel then keeps operating with hot air to blow-dry the evaporator, thus preventing the growth of mold and keeping the inside clean. -
When this function is turned on, the indoor unit display window appears “CL”, after 20 to 45 minutes, the unit will turn off automatically and cancel the ACTIVE CLEAN function.
NOTE: You can only activate this function in COOL or DRY mode.
Breeze away function
This feature avoids direct airflow blowing on the body.
NOTE: This feature is available under cool, FAN, and DRY mode only.
AP function
Choose AP mode to do wireless network configuration. For some units, it
doesn’t work by pressing the SET button. To enter the AP mode, continuously
press the LED button seven times in 10 seconds.
FRESH function
When the FRESH function is initiated, the ion generator is energized and will
help to purify the air in the room. Breeze away / fresh / sleep / follow me
function
LOCK function
Press the Turbo button and self-clean button simultaneously for one second to
lock or unlock the keyboard.
FOLLOW ME function
The follow-me function enables the remote control to measure the temperature
at its current location and send this signal to the air conditioner every
3-minute interval. When using AUTO COOL, or HEAT modes, measuring ambient
temperature from the remote control (instead of from the indoor unit itself)
will enable the air conditioner to optimize the temperature around you and
ensure maximum comfort.
SILENT function
Hold down the Fan button for 2 seconds to activate /cancel SILENT mode. Due to
the low-frequency operation of the compressor, it may result in insufficient
cooling and heating capacity.
SWING function
Swing Button
Used to stop or start vertical louver movement and set the desired left/right
airflow direction. The vertical louver changes 6 degrees in angle for each
press. I keep pushing for more than 2 seconds, the vertical louver auto swing
feature is activated.
Swing Button
Used to stop or start horizontal louver movement or set the desired up/down
airflow direction. The louver changes 6 degrees in angle for each press. I
keep pushing for more than 2 seconds, the louver will swing up and down
automatically.
Swing function:
Press swing function
The horizontal louver will swing up and down automatically when pressing SWING
button. Press again to make it stop.
Keep pressing this button for more than 2 seconds, the vertical louver SWING
function is activated (model dependent).
Wi-Fi operation setup
For instructions on setting up Wi-Fi connectivity for your Kaden air
conditioner, please scan the QR code below, or visit
kadenair.com.au
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>