i-PRO WV-QWL100 Wall Mount Bracket Instruction Manual

i-PRO WV-QWL100 Wall Mount Bracket

Important Information

• Before attempting to connect or install this product, please read these instructions carefully and save this manual for future use.
• The external appearance and other parts shown in this manual may differ from the actual product within the scope that will not interfere with normal use due to improvement of the product.

I-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.

“<Control No.: C****>” used in these documents should be used to search for information on our technical information website
(https://i-pro.com/global/en/surveillance/training-support/support/technical- information) and will guide you to the right information.

Caution:

• Before attempting to connect or operate this product, please read these instructions carefully

Notice:

• This product is not suitable for use in locations where children are likely to be present.
• Do not install this product in locations where ordinary persons can easily reach.
• For information about screws and other parts required for installation, refer to the corresponding section of this document.

Precautions

• Do not use this bracket except with suitable cameras.
  Failure to observe this may cause a drop resulting in injury or accidents.

• Refer installation work to the dealer.
  Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer.

• The screws and bolts must be tightened to the specified torque.
  Failure to observe this may cause a drop resulting in injury or accidents.

• Install the product securely on a wall in accordance with the installation instructions.
  Failure to observe this may cause injury or accidents.

• Do not rub the edges of metal parts with your hand.
  Failure to observe this may cause injury.

When using this product, also read the “Precautions” described in the operating instructions for the camera to be attached.

Preface

This product is a wall mount bracket that is designed to mount the network camera on a wall. The network camera will be installed after attaching this product to a junction box or concrete wall, etc.
The latest information about the supported cameras

Specifications

{6-1/2 inches (W) x 5-1/2 inches (H) x 8-9/16 inches (D)}
Mass:| Approx. 650 g {1.43 lbs}
Finish:| ABS resin, i-PRO white

Precautions for Installation

• In order to prevent injury, the product must be securely mounted to the wall according to the Installation Guide of this product.

• This product is designed to be used indoors.
  This product is not operable outdoors. Do not expose this product to direct sunlight for hours and do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation, discoloration and malfunction. Keep this product away from water and moisture.

• Installation area for this product

  • Make sure that the installation area is strong enough to hold the total weight of the camera assembly before installation.
  • Do not mount the product on a plaster board or a wooden section because they are too weak. If the product is unavoidably mounted on such a section, the section shall be sufficiently reinforced.

• Make sure to remove this product if it will no longer be used.

Standard Accessories

Screws ………………………………………………….5 pcs. (of them, 1 for spare)
(M4 x 4 mm {5/32 inches}, for securing camera mount bracket)
Template……………………………………………………………………………….1 pc.
Operating Instructions (this document)……………………………………….1 pc.

Other items that are needed (not included)
Fixing screw (M4) or anchor…………………………………………………… 4 pcs.

IMPORTANT

• Minimum pullout strength: 196 N {44 lbf} (per 1 pc.)
• Refer to our technical information website for information on the minimum pull-out strength.
• Select screws according to the material of the location that the camera will be mounted to. In this case, wood screws and nails should not be used.

Installation

Refer to the operating instructions of the camera for details on the camera installation (including the camera mounting, cable connection and adjustment).

Step 1
Put the template (accessory) against the wall and mark the positions of fixing screws (M4, locally procured) and the hole through which the cables are laid.
If cables are routed inside the wall, bore a hole through the wall.
Drill 4 holes on the wall to secure it with M4 screws. The hole diameter shall be decided in accordance with the specifications of the screws and anchors to be used. When the cables are laid inside the wall, drill a hole through the wall for cable installation.

Step 2
When connection is performed without drilling the wall for cable installation, cut off the notch marked with a circle drawn with a dotted line on the upper or lower case with a nipper for cable installation.

IMPORTANT

• To prevent injuries and protect the cables, finish the side cable access hole with a file to avoid sharp edges.

Step 3
Remove the lower case of the main unit.
The case can be removed by pulling down it while pressing the ribs (5 places) marked with arrows.

Step 4
Attach the camera mount bracket to the upper case.
Mount the camera mount bracket (camera accessory) with screws (M4 x 4 mm {5/32 inches}: accessory) in the consideration of the bracket direction as shown in the drawing right.
Recommended tightening torque: 1.56 N·m {1.15 lbf·ft}

Step 5
Attach the upper case and the chassis to the wall and run the cables.
Attach it with four screws. Screws are not provided. Prepare them in accordance with the camera installation position.
Necessary screw: M4 (4 pcs.) Minimum pull-out strength: 196 N {44 lbf} (per 1 pc.)

Step 6
Connect the cables to the external I/O terminals, audio input connector, or audio output connector. Refer to the operating instructions of the camera for descriptions of connections. Hold the camera main body fixing part securely at connections.
Step 7
Connect the cables to the RJ45 network terminal and power supply terminal (12 V DC). Refer to the operating instructions of the camera for descriptions of connections.

Step 8
Mount the camera onto the camera mount bracket.
Align the lock plate with the guide of the camera mount bracket, engage the bracket with the camera body while aligning the center of the bracket with the center of the camera, and rotate the camera body clockwise while pressing the camera to the camera mount bracket.

• Be sure to mount it with holding the camera main body fixing part.

Step 9
Secure the camera mount bracket to the camera with 1 piece of the camera fixing screw (M3, camera accessory).
Recommended tightening torque: 0.68 N·m {0.5 lbf·ft}

Step 10
Engage the 5 hooks to mount the lower case.
Ensure the lower case and the camera mount bracket are steadily fit with each other.

Step 11
Remove the decorative cover (lower) from the decorative cover supplied with the camera.
The decorative cover is secured with 3 hooks.

• The decorative cover (upper) is not used for mounting this product.
  

Step 12
① Align the “l” mark of the decorative cover (lower) with the arrow located above the lock lever of the camera body and insert it from underneath by holding the decorative cover (lower).

② Rotate the decorative cover (lower) clockwise when looking at it from underneath by approx.
16 degrees to insert it upward.
Rotate the decorative cover clockwise by 16 degrees more to secure it.

③ Ensure that the lock lever is securely inserted into the hole of the decorative cover (lower).

Note:

• WV-QDC100 (dome cover) can be also directly installed with this product. In such a case, the decorative cover (both upper and lower) supplied with the camera is not used.
• Follow the instructions as below to remove the decorative cover (lower).

① Rotate the lock lever by approx. 16 degrees counterclockwise when viewing the decorative cover (lower) from underneath (in the direction of ← in the drawing) while pressing the lock lever, and pull it slightly downward.
② Rotate the decorative cover (lower) more approx. 16 degrees counterclockwise (in the direction of ← in the drawing), and pull it out downward.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>