argo Evaporative Air Cooler Instruction Manual

argo Evaporative Air Cooler

OPERATING INSTRUCTIONS

Read the instructions carefully before operating the appliance or carrying out maintenance operations. Observe all the safety instructions; failure to observe the instructions may lead to accidents and/or damage. Keep these instructions in a safe place for future reference.

GENERAL SAFETY INFORMATION

•  Only use this appliance as described in this manual. Any other use not recommended by the manufacturer may cause
  fire, electric shock or injury to people.

•  Make sure that the type of mains power complies with the electrical requirements of the appliance (220-240V~/50 Hz).

•  This appliance can be used by children aged from 8 years and above and people with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

•  Children shall not play with the appliance.

•  Cleaning and user maintenance shall not be made by children without supervision.

•  This product is not a toy. Children should be adequately supervised to ensure that they do not play with the appliance.

•  Disconnect the mains power when the appliance is not used or for cleaning operations.

DESCRIPTION OF PARTS

1.  Control panel
2.  Buttons on control panel
3. Air outlet
4. Dust filter and evaporative panel
5.  Water tank
6. Multidirectional wheels

HOW TO USE THE APPLIANCE

The appliance does not need to be installed. Position the unit on a flat, stable surface and connect the power cord to a suitable power socket (220-240 V~): the appliance can be switched on using the ON/OFF button and you will hear a sound. When you move it, use the handle on the back. Do not use this cooler in an area with high humidity, rich in dust or with a temperature above 40 °C. This product can be used either as a fan, with 3 modes (Normal, Natural and Sleep) and 3 fan speed options (low, medium and high), or as a cooler/humidifier: in this case the rear tank should be filled with demineralized water, up to but not exceeding the maximum level as indicated. When the water in the tank falls below the minimum level, marked on the tank, LED Low water on control panel will flash to indicate the leak of water. The fan takes in air from the room and passes it through the dust filter and the evaporative panel, which is constantly humidified thanks to a system which draws water from the tank and sprays it onto the panel. The incoming hot air makes part of the water contained in the panel evaporate and is therefore cooler when released back into the room, which makes it feel as though the temperature has dropped.

REMOTE CONTROL

DISPLAY AND CONTROL PANEL

• ON/OFF BUTTON Press this button on the control panel to turn the unit on or off. The default operating mode is low ventilation (speed 1) and General ventilation

• SPEED BUTTON When the appliance is on, press the SPEED button to choose the fan speeds which are: high (speed 4), medium (speed 3), low (speed 2), very low (speed 1). Each time the SPEED button is pressed, the fan speed will increase from 1 to 4 in a circularly. The corresponding LED on the control panel will light up at the selected speed. The SPEED function is not present on the remote control

• TIMER/PRESET BUTTON Timer off function: With the unit on, press this button to select the time of appliance turning off, each press of the button allows you to set the shutdown interval from 1 to 15 hours, the LEDs on the control panel will light up based on your selection. Once the selected interval is reached, the unit will turn off automatically. By holding down the Timer / Preset button it is possible to speed up the setting of the Off Timer.

• MODE BUTTON When the unit is on, press this button to select the ventilation mode in the following sequence: General – Natural – Sleep, the corresponding LEDs on the control panel will light up according to the selection made.

  •  General: The unit operates at a constant ventilation speed
  •  Natural: The unit works according to the factory settings, the ventilation speed changes automatically.
  •  Sleep: The ventilation speed decreases every hour until it reaches the minimum ventilation level.

• L &R SWING BUTTON  With the unit on, press this button to select the horizontal swing from right to left of the air flaps. The corresponding Swing ON or Swing OFF LEDs will be lit on the control panel upon your selection. On the remote control it is indicated with SWING.

• HUMIDIFY BUTTON With the unit turned on, press this button to activate or deactivate the humidification function. If this function is activated, the corresponding LED on the control panel will light up.
  Note : Before activating the humidification function, check the water level in the tank, which must be above the water level indicator. If there is not enough water, add it to the tank.

• LOW WATER LED When the water in the tank is not enough to activate the humidification function, the Low Water LED flashes on the control panel. Add water to the tank and activate the humidification function.

• HALF LIGHT DISPLAY When any selection on control panel are made for more than 40 seconds, the LEDs on the display reduce the light. To reactivate them, press any of the buttons on the control panel.

• MEMORY FUNCTION This device is equipped with the Memory function, which allows you to memorize the selected settings after turning off the unit. When the device is turned on, it will work with the previously memorized settings.

• AUTO OFF FUNCTION When the unit works for 15 consecutive hours and no selections are made on the control panel, the device automatically switches off.

REMOTE CONTROL OPERATION

1.  Slide the cover open in the direction indicated by the arrow.
2.  Insert the batteries (AAA, LR03, 1,5 V – not provided) into the remote control and make sure the poles match.
3.  Put the cover back on.
4.  Point the remote control towards the receiver on the air conditioner.
5.  The remote control should be positioned within 6 metres from the receiver.
6. There must be no obstacles between the remote control and the receiver.
7.  Do not drop or launch the remote control.
8.  Do not leave the remote control under strong sunlight or heating devices and other source of heat.
9.  Remove the batteries from the remote control when the latter is not used for a long time.
10. If no sound is heard and the transmission symbol on the display does not flash, the batteries must be replaced.
11.  If the system resets when the remote control button is pressed, the electrical signal is poor and the batteries must be replaced.
12. Flat batteries must be disposed of correctly.

DISPOSAL

INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EUROPEAN DIRECTIVE 2006/66/EC and amendments Directive 2013/56/EC Please replace the battery when its electrical charge has been exhausted: at the end of its useful life, it must not be disposed of together with unsorted waste. It must be must be delivered to appropriate separated waste disposal plants or to dealers that provide a similar service. Separate waste disposal of batteries prevents potential negative effects on the environment and human health resulting from inadequate disposal, and also allows the materials from which it is made to be recovered and recycled in order to achieve significant savings in terms of energy and resources. The separate disposal obligation is underlined by the crossed-out dustbin symbol appearing on the battery. Illegal disposal of the product by the user shall result in the application of administrative sanctions as defined by current regulations.

FILLING THE WATER TANK

THE TANK MUST BE FILLED WITH DEMINERALIZED WATER FOR THE APPLIANCE TO OPERATE IN COOLER/HUMIDIFIER MODE.
The water is inserted directly into the rear tank. Before introducing the water, check that there are no water residues inside the water pump, to prevent its leakage. Fill the tank up to the maximum level marked on the water indicator, without exceeding the water level limit, this could cause water leakage. When using the appliance for first time, remove the cardboard support positioned inside the tank.

If you wish to keep the water in the tank below room temperature in order to maximize cooling in warmer months, leave the two synthetic ice packs supplied in the freezer until solid, then add them to the water in the tank.
The ice will absorb heat from the water. With the unit off, place the ice packs directly in the tank in the position shown in the figure below, inside the tank there is a special space where to place the ice packs. Make sure that the tank can be pulled out normally.

We recommend continuous use of the ice for optimal cooling capacity. Ice packs can be used repeatedly. The first time it is used, you may detect a smell or the water may turn an unusual color: this does not constitute a health risk.

MAINTENANCE AND STORAGE

Cleaning the outside surface of the appliance
Use a soft cloth to remove any dust from the product. If this is not enough, use a soft cloth dampened with water and a mild detergent at a temperature not exceeding 50°C. Let the appliance dry completely before using it.
Do not use corrosive detergents or solvents such as petrol. Do not wash the appliance with water. Do not use oils, chemical substances or other items that may damage the surface to clean it. Use a vacuum cleaner to remove dust from the air inlet/outlet grilles. When the appliance is used for a long time, the tank, the tank filter, the honeycomb filter and the dust filter may have accumulated dust, this could affect the air flow and the effect of cooling. It is therefore advisable to clean these parts every two weeks.

Cleaning the dust filter and the honeycomb filter
Remove the filter assembly by detaching it from the unit by pressing on the opening hook. Once removed, gently remove the honeycomb filter by sliding it under the hooks, remove the dust filter, always sliding it off the hooks, following the direction of the guides. To assemble again, insert the dust filter in its holder and then insert the honeycomb filter (see Fig. 1) Make sure all components are perfectly dry and properly installed to avoid damaging them.

Cleaning the tank and the water channel
To clean the water tank, remove it from its seat and clean it thoroughly with a dry cloth. Remove the filter positioned inside the tank, clean it and let it dry before repositioning it. After removing the tank, carefully clean the water channel with a cloth from any residual water that may have formed.

STORAGE

If the appliance is not used for prolonged periods, disconnect the power cord and store the appliance with this manual in its original packaging, in a cool and dry place. Before packaging, the honeycomb filter and dust-proof filter should be dry, and there is no water in the tank.

POSSIBLE OPERATING PROBLEMS AND SOLUTION
If the appliance has any operating anomalies, consult the table below to resolve any anomalies. If they persist, contact an authorized service center to repair the appliance.

The appliance does not work

| The power cord is not connected or is not connected properly

The appliance is off Internal wiring is loose

| Connect it correctly

Put the water in the tank Contact a service center

It does not humidify / the water pump makes an abnormal sound

| There is no water in the tank or the amount of water is below the minimum water level

The water pump cannot draw water

The water pump filter is blocked

The hole in the honeycomb filter is blocked

The water pump is damaged or the internal connections are missing

| After turning off the unit, add water to the tank up to the maximum level indicated

Repeatedly press the Humidity button on the control panel until the water pump starts drawing water again

Clean the filter

Clean the honeycomb filter Contact a service center

Abnormal sound of the unit

| The device is not placed on a stable and flat surface

There may be dust residues in the appliance

The air delivery flaps have not been opened

Problem with the motor of the air flaps

| Place the device on a flat and stable surface

Remove the honeycomb filter and eliminate the accumulation of dust inside the unit

Manually open the air delivery flaps

Contact a service center

The 1h, 2h, 4h and 8h indicators flash twice and then go off for 3 seconds| Communication problem between the main board and the display board| Contact a service center
The 1h, 2h, 4h and 8h indicators flash four times and then go off for 3 seconds| Malfunction of jumper cup| Contact a service center

INFORMATION FOR THE CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EUROPEAN DIRECTIVE 2012/19/EU
This appliance may not be scrapped with domestic waste at the end of its life cycle. We call your attention to the crucial role played by the consumer in the re-use, recycling and other forms of recovery of such waste. The appliance must be scrapped by a sorted waste disposal centre or by returning it to the retailer (no charge is levied for this service), when you purchase a new equivalent appliance. Sorted disposal of electric and electronic equipment prevents the negative effects on the environment and human health resulting from improper scrapping, and also allows the materials from which it is made to be recovered and recycled, with significant savings in terms of energy and resources. The sorted disposal requirement is indicated by the crossed waste bin label affixed to the appliance.

References

• Argoclima S.p.A.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>