HIKER AUDIO S1 True Wireless Earbuds User Manual

HIKER AUDIO S1 True Wireless Earbuds User Manual

Introduction

Thank you for choosing HIKER AUDIO S1 Wireless headphones. Please read the manual carefully, and keep it for further reference.

Package Content

Product Diagram

1. USB Charging Pod
2. Volurre+/Next Track
3. Multifunctional Button
4. LED Indicator/Microphone
5. Volume-/Previous Track

Specifications

Button Control

Power On| Press and hold the Multifunctional Button for 3s until the led
light flashes blue
---|---
Power Off| Press and hold the Multifunctional Button for 3s until the led
light flashes red
Play / Pause| Short press the Multifunctional button
Volume +1-| Short press the +1-button
Play Next/Previous| Long press the +/- button for 2 seconds
Answer Phone Call| Short press the multifunctional Button
Hang Up| Short press the Multifunctional Button in an active call
Reject Phone Cal| Press the Multifunctional buffon for 1.5s
Mute / Resume A Call| Double tap the MFB during a call
Transfer Between
Headset and Phone| Press the Multifunction button for 1.5s during a cal
Activate Voice Assistant| Double press the Multifunctional button while in playing or pausing mode
Factory Reset| Press the Multifunction button for 3s when the headset is
charging

LED Indicators

Wearing

1. Identify the right and left earpieces.
2. Insert the earbuds into your ears. Adjust the ear fins direction and put them into your ears.
3. Adjust each earpiece until it fits flush in your ear and the ear tip seals in the ear canal.

Get Started

Pairing

1. Power on the headset, press and hold the Multifunctional button for approximate-ly 3 seconds until the LED indicator flashes blue quickly(you will hear the voice prompt “power on” first, just keep holding the multifunctional button ). Now the headset is in pairing mode.
2. Activate the Bluetooth on your device and search for the nearby Bluetooth connection: For iPhone/iPad/iPodO: Settings -> Bluetooth -> On For AndroidlM: Setting ->Wireless & Networks -> Bluetooth -> On -> Scan for devices For Windows® Phone devices: Settings -> Bluetooth -> On
3. HIIERAUDIOS1″ should be listed in the search result. Select the name to connect. Once connected, the indicator will be solid blue. You will hear a voice prompt”Your headset is connected”.

Notes:

1. When you want to unpair the headset with the device, just press the volume buttons + and – simultaneously for about 3s.
2. The HIK Z1S headset will stay in pairing mode for 3 minutes at most if no pairing device is found. Afterwards, it will power off automatically.

Charging

1. Connect the charging port with any USB charging adapter or charging port available. Charging starts automatically with LED indicator turning red and the headset turns off.
2. The headset is fully charged when the LED indicator turns blue.

Name and Content of Hazardous Substance

This chart is prepared in accordance to the provisions prescribed in SJ/T 11364.
0: Denotes the hazardous substance content in all homogenous materials used in this component is below the limit as stipulated in GB/T 26572-2011.
x : Denotes the hazardous substance content in at least one of the homogenous materials used in this component exceeds the limit as stipulated in GB/T 26572-2011; however, due to no viable alternative solution in the industry currently, it still conforms to the environmental requirements of the EU directive RoHS.

FCC Statement

FCC Warning:

This equipment has been testedand found to complywiththe limitsforaClassB digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmfulinterference in a residential installation. This equipment generates,uses and can radiateradio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interferencewill not occurin a particularinstallation, If this equipment does cause harmful interference to radioor television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receivingantenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on acircuit different from that to which the receiver is connected.
• Consultthe dealeror an experiencedradio/ TV technician for help.

This device complieswith part 15 of the FCC Rules.

Operationis subject tothe following two conditions:
(1) This devicemay not cause harmful interference,and
(2) This device must accept any interference received, including interference that may cause undesired operation

Changes or modifications not expresslyapproved by the party responsible for compliance could void the user’s authorityto operate the equipment.

FCC RF warning statement:

The device has been evaluated to meet general RF exposure requirement.

The device can be used in portable exposure condition without restriction

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>