Clarke CTBJ5 5 Tonne Telescopic Bottle Jack Instruction Manual

June 6, 2024
Clarke

Clarke CTBJ5 5 Tonne Telescopic Bottle Jack Instruction Manual
Clarke CTBJ5 5 Tonne Telescopic Bottle Jack

INTRODUCTION

Thank you for purchasing this CLARKE Bottle Jack.
Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.
Keep these instructions for future reference.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.

This guarantee does not effect your statutory rights.

SPECIFICATIONS

SAFETY PRECAUTIONS

  1. Do not exceed the rated capacity of the jack.
  2. Do not allow personnel to operate the jack unless they have read these safety precautions.
  3. Do not operate the jack if damaged.
  4. Use the jack in a suitable, well lit work area.
  5. Keep the work area clean and tidy and free from unrelated items.
  6. Only use the jack on level and solid ground, preferably concrete. Avoid soft/unmade ground as the jack may sink in.
  7. Ensure non-essential persons keep a safe distance whilst the jack is in use.
  8. Ensure there are no personnel or obstructions under the vehicle before lowering.
  9. Do not work under the vehicle until it is fully supported by axle stands.
  10. Keep hands etc clear of the vehicle until lifting is complete.
  11. Ensure that you can see the saddle and jacking point throughout the jacking operation in case there is any relative movement.
  12. Always ensure that the jack saddle is centred and stable on the lifting point before lifting and position the jack to avoid operating it from under the vehicle.
  13. Check the vehicle weight and recommended lifting points by referring to the vehicle owners manual. Ensure the lifting point is not corroded.
  14. Never tamper with the jack or modify it in any way, as this could prove to be dangerous and will invalidate the guarantee. Only use the jack for the purpose for which it is intended.
  15. Use appropriate safety equipment, such as protective footwear, when using this jack.
  16. Ensure that the jack is properly maintained and lubricated at all times, and that no corrosion is allowed to weaken any part of it.
  17. If the jack has been subjected to an abnormal load or shock, it should be removed from service immediately and fully inspected by qualified personnel, and passed as serviceable, before being used again.
  18. When not in use, store the jack, fully lowered, in a safe, dry, childproof area.
  19. Always inspect the jack before use. Ensure that all parts are in good condition and operating smoothly, and that no cracks or distortion is apparent. If in doubt do not use.
  20. Never push a vehicle off the jack or start the engine while supported only by the jack.
  21. Do not use if an oil leak is apparent. Consult the Clarke Service Department.
  22. If more than one jack is used in unison, they must all be of the same rating and be raised at the same speed to reduce the possibility of the load slipping.

SAFETY SYMBOLS
The following safety symbols may be found on the product.

Read the user manual before use.

LIFTING OPERATIONS AND LIFTING EQUIPMENT REGULATIONS 1998

This jack, depending on use, may fall within the scope of LOLER. It is the owner’s responsibility to determine whether or not it does and, if so, to comply with any applicable requirements in LOLER, for having the jack thoroughly examined.

ENVIRONMENTAL PROTECTION
  1. Take care to ensure that if hydraulic oil is spilt that it is cleaned away using sand or treated with absorbent granules designed for the purpose.
  2. Always make every effort to contain any spillage and prevent ingress into the local water course

PRODUCT FEATURES

(CTBJ12 shown)

1 3 x Handle Tubes
2 Ram
3 Screw Extension
4 Oil Filler Plug
5 Actuating Lever
6 Release Valve
UNPACKING

During transit or storage, it is possible that an air pocket may have developed within the hydraulic ram, and the ram action may therefore appear to be ‘spongy’. In this case the jack may require purging as described.
If the column does not reach its full height, the ram oil level may require topping up, as described in the Maintenance section.

OPERATION

WARNING: ENSURE THE SAFETY PRECAUTIONS ARE STRICTLY FOLLOWED. NO RESPONSIBILITY CAN BE ACCEPTED FOR INCORRECT USE OF THE JACK

RAISING A VEHICLE

  1. Ensure the vehicle is stable and is on firm level ground with the wheels chocked before positioning the jack so that is directly beneath the lifting point. DO NOT rely upon the vehicle handbrake alone to prevent vehicle movement.
  2. Ensure the jack is on solid ground. If not, place a suitable piece of solid wood of sufficient size to provide adequate support beneath the jack.
  3. Consult the vehicle owners manual to ascertain the location of suitable jacking points and position the jack beneath the designated lifting point.
  4. Locate the slotted end of the jack handle on to the release valve and turn fully clockwise to close the valve.
  5. Set the screw extension (CTB10 & 12 models) in contact with the lifting point. Pump the handle and raise the ram so that the jack and lifting point are in full contact. Before proceeding further, make one final check to ensure that:
    • the jack is completely vertical and stable.
    • there are no obstructions to the lift and that the handle can move freely up and down.
    • all personnel are in a safe position.
  6. When satisfied, continue to pump the handle and lift the load to the height required.
    NEVER allow anyone to get beneath the load until it is firmly supported on suitable, properly rated axle stands.
LOWERING THE VEHICLE

WARNING: ALWAYS LOWER IN A SLOW AND CONTROLLED MANNER, AND CHECK THAT THERE ARE NO OBSTACLES IN THE PATH OF THE LOAD’S DESCENT. BE EXTREMELY CAREFUL WHEN LOWERING HEAVY LOADS.

  1. The lowering speed is controlled by the amount you turn the release valve. With the axle stands removed, check to ensure that there are no personnel in the immediate vicinity before removing the handle from its housing, and engaging it with the release valve.
  2. Very slowly turn the handle anticlockwise to open the release valve, and allow the jack to lower the load, under complete control. NEVER, under any circumstances, jerk the valve open.

MAINTENANCE

IMPORTANT: Only fully qualified personnel should attempt to repair the jack.

INSPECTION

  1. Always visually inspect the jack before use, to ensure that all parts are correctly located and secure. Check for hydraulic leaks, signs of damage or worn parts. Do not use the jack unless it is perfectly serviceable.
    • A slight dampness on the ram is normal, but where leakage is found, the ram seals must be renewed by your Clarke Spares Department.
  2. The jack should be fully inspected annually as follows:
    • Check for cracks and deformation of components.
    • Check operation and top up the oil level. (see below).
    • Remove completely, any rust or corrosion and repaint to prevent further corrosion.
    • Ensure that all decals and warning notices are in place and legible.
  3. After use, store the jack with the ram in its lowest position. This not only relieves the hydraulic ram, but also prevents any possibility of corrosion to the ram.
  4. Do not leave the jack in the open, exposed to the weather. Keep under cover. If stored for long periods, inspect before use, clean, and re-oil. For servicing, contact your CLARKE dealer or CLARKE Service dept.

TOPPING UP THE OIL

It may be necessary from time to time to top up the hydraulic oil level.

Proceed as follows.

  1. Turn the release valve counterclockwise and allow the ram to retract to its lowest position.
    • It may be necessary to apply force to the saddle for lowering without any weight on the jack.
  2. With the jack in the level position, remove the filler plug and stand upright.
    • The oil should be level with the bottom of the oil filler hole.
  3. If below this, top up.
  4. Do not overfill. Only use the correct type of oil such as Clarke hydraulic oil (part number 3050830).
  5. Replace the filler plug.
  6. Check the jack for correct operation and purge any air from the system as described below.
PURGING AIR FROM THE JACK
  1. Turn the release valve counterclockwise one full turn to open.
  2. Pump the handle eight full strokes.
  3. Turn the release valve clockwise to close the valve.
  4. Pump the handle until the ram reaches maximum height and continue to pump several times to remove trapped air.
  5. Turn the release valve counterclockwise one full turn and lower the ram to its lowest position. Apply pressure if necessary.
  6. Turn the release valve clockwise to the closed position and check for correct operation. It may be necessary to perform the procedure more than once to evacuate all the air.

TOPPING UP THE OIL

It may be necessary from time to time to top up the hydraulic oil level.

Proceed as follows.

  1. Turn the release valve counterclockwise and allow the ram to retract to its lowest position.
    • It may be necessary to apply force to the saddle for lowering without any weight on the jack.
  2. With the jack in the level position, remove the filler plug and stand upright.
    • The oil should be level with the bottom of the oil filler hole.
  3. If below this, top up.
  4. Do not overfill. Only use the correct type of oil such as Clarke hydraulic oil (part number 3050830).
  5. Replace the filler plug.
  6. Check the jack for correct operation and purge any air from the system as described below.

PURGING AIR FROM THE JACK

  1. Turn the release valve counterclockwise one full turn to open.
  2. Pump the handle eight full strokes.
  3. Turn the release valve clockwise to close the valve.
  4. Pump the handle until the ram reaches maximum height and continue to pump several times to remove trapped air.
  5. Turn the release valve counterclockwise one full turn and lower the ram to its lowest position. Apply pressure if necessary.
  6. Turn the release valve clockwise to the closed position and check for correct operation. It may be necessary to perform the procedure more than once to evacuate all the air.

TROUBLESHOOTING

Problem Check Solution
Jack will not lift to full height Low oil level Check oil level
Jack will not hold load Release valve not closing Hydraulic oil contaminated
Pump valves not sealing Cylinder ram binding Contact Clarke Service

Department
Jack piston will not lower| Cylinder ram binding Parts warn
Internal  damage Broken or disconnected return spring
Lift arm linkage bent or binding| Contact Clarke Service Department
Jack feels spongy when lifting| See Air Purging section| See air purging procedure above

PARTS DIAGRAMS

CTBJ5
Product Overview
CTBJ10 & CTBJ12
Product Overview
CTBJ5, CTBJ10 & CTBJ12 PARTS LIST

No CTBJ5 CTBJ10/12
1 Release valve Release valve
2 O-ring O-ring
3 Steel Ball Steel Ball
4 Filler Plug Filler Plug
5 Base Casting Base Casting
6 O-ring Sealing Ring
7 O-ring Circlip
8 Breech Block O-ring
9 Circlip O-ring
10 Piston Ring Sealing Ring
11 Piston Ring Circlip
12 Circlip Circlip
13 Outer Piston Sealing Ring
14 Circlip O-ring
15 Nylon Ring O-ring
16 Block Ring Circlip
17 Piston Ring Lower Piston
18 Nylon Ring Circlip
19 Piston Head Sealing Ring
20 Gasket Circlip
21 Inner Piston Sealing Ring
No CTBJ5 CTBJ10/12
--- --- ---
22 Circlip O-ring
23 Cap Nut Piston Head
24 Circlip O-ring
25 Link Plate Upper Piston
26 Handle Bracket Circlip
27 Hinge Pin Screwed Rod
28 Pump Piston Spring
29 Dustproof Ring Cap Nut
30 Circlip Circlip
31 O-ring Link Plate
32 Housing Handle Bracket
33 Valve End Hinge Pin
34 Gasket Pump Piston
35 Nylon Ring Dustproof Ring
36 Nylon Ring Circlip
37   O-ring
38   Valve Housing
39   Valve End
40   Gasket
41   Nylon Ring
42   Nylon Ring

DECLARATIONS OF CONFORMITY

Certificates

COMPANY PRODUCT

  • AIR COMPRESSORS
    From DIY to industrial. Plus sr tools. spray guns and accessories.

  • GENERATORS
    Prime00y or emergency standby for business, home and leisure.

  • POWER WASHERS
    Hot and cold electric and angina driven we have wive you need

  • WELDERS
    Mig,Arc.Tig and Spot. From OlY to autalindustrial.

  • METALWORKING
    Drills. grinders and saws for DIY and profealonaf use.

  • WOODWORKING
    Saws. sanders, lathes. meetisers and dust extraction.

  • HYDRAULICS
    Cranes, body repair kgs. transmission jacks for all types of workshop use.

  • WATER PUMPS
    subrner sge, electric and engine driven for DIY. agriculture and industry.

  • POWER TOOLS
    Anglewinders. cordless drill sets. son and sanders.

  • STARTER SIC I4ARGE RS
    All sizes for car and commercial use

CUSTOMER SUPPORT

PARTS & SERVICE:
0208 988 7400
Parts Enquiries
Parts@clarkeinternational.com
Servicing & Technical Enquiries
Service@clarkeinternational.com
SALES: UK 01992 565333 or Export 00 44 (0)1992 565335
Clarke INTERNATIONAL Hemnal Street, Epping. Essex CM16 41..G
www.clarkeinternationat.com


Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals