beflex Coach True Wireless Earbuds User Guide
- June 6, 2024
- beflex
Table of Contents
- beflex Coach True Wireless Earbuds User Guide
- Remove the protective stickers.
- Turn on Bluetooth®
- Connect Beflex Coach.
- Register with Beflex app.
- Run with Beflex Coach
- Find the most comfortable fit.
- Button functions
- LED status.
- Charge earbuds.
- Reset earbuds.
- SPECIFICATIONS
- FCC STATEMENT
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
beflex Coach True Wireless Earbuds User Guide
Remove the protective stickers.
Remove the battery-drain prevention stickers on each earbuds. Place them back in the case to activate the earbuds .
Remove protective sticker.
Place back in case to activate the device.
Turn on Bluetooth®
Turn on the Bluetooth function on your smartphone.
Connect Beflex Coach.
Take the earbuds out of the charging case. The earbuds will enter pairing mode automatically. Connect Beflex Coach via Bluetooth.
Register with Beflex app.
Download and register your device with Beflex app.
Run with Beflex Coach
Start your first run on Beflex app.
Find the most comfortable fit.
Test different eartips and earwings.
Rotate to fit the most comfortable position
Button functions
Single Press •
Ambient Mode Play/Pause
Double Press •• Previous Song Next Song
Long Press – Voice Assistant Voice Assistant
LED status.
Case LED shows the charging status of the case battery
Case battery is sufficient SLessthan 1 full charge for earbuds
Charge earbuds.
Place the earbuds inside the case to charge the earbuds. Connect USB-C to the charging case.
Reset earbuds.
Place both earbuds inside the charging case. Press both buttons on the two earbuds at the same time for 6 seconds. Earbuds LED will blink 2 times if reset is successful.
SPECIFICATIONS
General
Model name
Model number
Product name
Weight
Dimensions
Waterproof
Button interface
Charging port
Microphone
Manufactured country
BiomechEngine®
Chip version
Bluetooth® specs
Version
Chipset
Profiles
Codec
Bluetooth range
Audio
Driver unit
Frequency range
Magnet type
lmpedence
Battery*
Capacity
Playtime (continuous)
Playtime (total)
Charging time
Standby time| BeflexCoach
BFCl00
True wireless earphone
Earbud (each): 5.7g / Charging case: 31g
Earbud (each): 17.1 x 20.2 x 22mm
Charging case: 71 x 35.1 x 29mmm
IP67
Physical button
USB-C
Dual-mic “‘2
China
BME-300
5.2
QCC3040
HFP, A2DP, AVRCP
SBC, AAC,APTX
~lOm
6.0mm, 2xdynamic
20-20KHz
Neodymium
160
Earbud (each): SOmAh
Charging case: 410mAh Li-ion Polymer
Up to 7 hours
Up to 28 hours with charging case (3 full charge)
Charging earbuds by case takes 1.5 hours
Charging both earbuds and case takes 2 hours
80 hours for earbuds
*Battery playtime may differ depending on the device type, volume level, environment, usage, and many other factors.
Biomech Engine® is the registered trademark owned by Beflex Inc.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks is under license. Qualcomm apt X
and Qualcomm True Wireless are products of Qualcomm
Technologies, Inc. and/or its subsidiaries. Other trademarks and trade names
are those of their respective owners.
FCC STATEMENT
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help. This
device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions (1) this device may not cause harmfulinterference,
and (2) this device must accept anyinterference received,including
interference that may cause undesired operation.
Copyright© 2020 Beflex Inc. All rights reserved.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks is under license.
Other trademarks and trade names are those of their respective owners.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>