coolpad CP332A Wi-Fi Hotspot Sprint 4G LTE User Guide
- June 6, 2024
- Coolpad
Table of Contents
- Important Health Information and Safety Precautions
- Safety Precautions for Proper Grounding Installation
- Safety Precautions for Power SupplyUnit
- Electrical Safety
- Safety Precautions for Direct Sunlight
- Environmental Restrictions
- Aircraft Safety
- Safety Precautions for RF Exposure
- Explosive Atmospheres
- Interference with Medical Equipment Functions
- Non-ionizing Radiation
- Battery Information and Precautions
- Safety Instructions of Travel
- FCC Notice and Cautions
- TIA Safety Information
- Safety Information
- Consumer Information on SAR
- Standard Limited Warranty
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Health & Safety
Warranty Guide
Important Health Information and Safety Precautions
When using this product, the safety precautions below must be taken to avoid
possible legal liabilities and damages. Retain and follow all product safety
and operating instructions.
Observe all warnings in the product operating instructions. To reduce the risk
of bodily injury, electric shock, fire and damage to the device, closely
observe all of the following precautions.
Safety Precautions for Proper Grounding Installation
Caution: Connecting to improperly grounded equipment can result in an electric shock to either you or your device. This product is equipped with a USB Cable for connecting to a desktop or notebook computer. Be sure your computer is properly grounded before connecting this product to the computer. The power supply cord of a desktop or notebook computer has an equipment- grounding conductor and a grounding plug. The grounding plug must be plugged into an appropriate outlet which is properly installed and grounded in accordance with all local codes and ordinances.
Safety Precautions for Power SupplyUnit
Use the correct external power source. A product should be operated only from the type of power source indicated on the electrical ratings label. If you are not sure of the type of power source required, consult your authorized service provider or local power company. For a product that operates from battery power or other sources, refer to the operating instructions that are included with the product.
Electrical Safety
This product is intended for use when supplied with power from the designated
battery or power supply unit. Other usage may be dangerous and will invalidate
any approval given to this product. Handle battery packs carefully. This
product contains a Li-ion battery. There is a risk of fire and burns if the
battery pack is handled improperly. Do not attempt to open or service the
battery pack. Do not disassemble, crush, puncture, short external contacts or
circuits, dispose of in fire or water, or expose a battery pack to
temperatures higher than 60°C (140°F).
Note: Danger of explosion if battery is incorrectly replaced. Replace
only with specified batteries. To replace the battery, take the device to an
authorized service centre. Recycle or dispose of used batteries according to
all applicable local regulations, or in accordance with the instructions in
the reference guide.
Follow these other specific precautions:
- Keep the battery or device dry and away from water or any liquid as it may cause a short circuit.
- The device should be connected only to products that bear the USB-IF logo or have completed the USB-IF compliance program.
- Keep metal objects away so they do not come in contact with the battery or its connectors as it may lead to short circuit during operation.
- Always keep the battery out of the reach of babies and small children to avoid swallowing. Consult a doctor immediately if the battery is swallowed.
- Do not use a battery that appears damaged, deformed, discolored, has any rust on its casing, if it overheats, and/or if it emits a foul odour.
- Use of an unqualified battery or charger may present a risk of fire, explosion, leakage or other hazard.
- Only use the battery with a charging system that has been qualified with the system per this standard: IEEE-Std-1725-200x.
- Use of an unqualified battery may present a risk of fire, explosion, leakage or other hazard.
- Replace the battery only with another battery that has been qualified with the system per this standard: IEEE-Std-1725-200x.
- Avoid dropping the device or battery. If the device or battery is dropped, especially on a hard surface causing damage, take it to a service center for inspection.
- If the battery leaks: Do not allow the leaking fluid to come in contact with eyes. If contact occurs, DO NOT rub the eyes. Rinse with clean water immediately and seek medical advice. Do not allow the leaking fluid to come in contact with skin or clothing. If contact occurs, flush the affected area immediately with clean water and seek medical advice. Take other precautions to keep a leaking battery away from fire as there is a danger of ignition or explosion.
Safety Precautions for Direct Sunlight
Store this product away from excessive moisture and extreme temperatures. Do not leave the product or its battery inside a vehicle or in places where the temperature may exceed 60°C (140°F), such as on a car dashboard, window sill, or behind glass that is exposed to direct sunlight or strong ultraviolet light for extended periods of time. This may damage the product, overheat the battery, or pose a risk to the vehicle.
Environmental Restrictions
Do not use this product in gas stations, fuel depots, chemical plants or where blasting operations are in progress, or in potentially explosive atmospheres such as fueling areas, fuel storehouses, below deck on boats, chemical plants, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles, such as grain, dust, or metal powders. Please be aware that sparks in such areas could cause an explosion or fire resulting in bodily injury or even death.
Aircraft Safety
Due to the possible interference caused by this product to an aircraft’s navigation system and its communications network, using this device on board an airplane is prohibited in most countries.
Safety Precautions for RF Exposure
- Use of non-original, non-manufacturer-approved accessories may violate your local RF exposure guidelines and should be avoided.
- Use only original, manufacturer-approved accessories when such accessories contain metal of any kind.
- Avoid using your device near strong electromagnetic sources, such as microwave ovens, sound speakers, TV and radio.
- Avoid using your device near metal structures (for example, the steel frame of a building).
Explosive Atmospheres
When in an area with a potentially explosive atmosphere or where flammable materials exist, the device should be turned off and the user should obey all signs and instructions. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Users are advised not to use the equipment at refueling points such as service or gas stations, and are reminded of the need to observe restrictions on the use of radio equipment in fuel depots, chemical plants, or where blasting operations are in progress. Areas with a potentially explosive atmosphere are often, but not always, clearly marked such as fueling areas, below deck on boats, fuel or chemical transfer or storage facilities, and including, but not limited to areas where the air contains chemicals or particles such as grain, dust, or metal powders.
Interference with Medical Equipment Functions
This product may cause medical equipment to malfunction. The use of this device is prohibited in most hospitals and medical clinics for which regulations and rules are commonly posted in such facilities. In these instances, turn your device OFF as health care facilities frequently use equipment that is adversely affected by RF energy. If you use any personal medical device(s), consult the manufacturer of your device(s) to determine if the device(s) is adequately shielded from external RF energy. Your health care provider may be able to assist you in obtaining this information.
Non-ionizing Radiation
Your device has an internal antenna. This product should be operated in its
normal-use position to ensure the radiative performance and safety from
interference. As with other mobile radio transmitting equipment, users are
advised that for satisfactory operation of the equipment and for personal
safety, it is recommended that no part of the human body should come too close
to the antenna during equipment operation.
Use only the supplied integral antenna. Use of unauthorized or modified
antennas may impair call quality and damage the device, causing loss of
performance and SAR levels exceeding the recommended limits, as well as
causing non-compliance with local and national regulatory requirements. In
order to limit RF energy exposure and to ensure optimal device performance,
operate the device only it its normal-use position. Contact with the antenna
area may impair call quality and cause your device to operate at a higher
power level than needed which can reduce antenna performance and battery life.
Battery Information and Precautions
To assure product safety, there shall be precautions below.
Danger!
- Use dedicated chargers and follow the specified conditions when charging the cell.
- Use the cell only with the specified equipment.
- Do not put or store cell together with metal articles such as necklaces, hairpins, coins, or screws.
- Do not short circuit the (+) and (-) terminals with metal conductors.
- Do not place cell in a device with the (+) and (-) in a reverse way.
- Do not penetrate cell with a sharp articles such as a needle.
- Do not disassemble the cell.
- Do not weld the cell directly.
- Do not use a seriously damaged or deformed cell.
- Thoroughly read the user’s manual before use, Inaccurate handling of the lithium-ion cell may result in heat, fire, explosion, damage or the capacity loss of the cell.
Warning!
- Do not put cell into a heating vessel, washing machine or high-pressure container.
- Do not use cell with primary batteries, or batteries of a different package, type, or brand.
- Stop charging the cell if charging is not completed within the specified time.
- Stop using the cell if abnormal heat, odor, discoloration, deformation or abnormal condition is detected during use, charge, or storage.
- Keep away from cell immediately when leakage or foul odor is detected.
- Wash well with clean water immediately if liquid leaks onto your skin or clothes.
- If liquid leaking from the cell gets into your eyes, do not rub your eyes. Wash them well with clean water and call physician immediately.
Caution!
- Store batteries out of reach of children so that they are not accidentally swallowed or handled.
- If younger children use the cell, their guardians should explain the proper handling.
- Be sure to read the user’s manual and cautions on handling thoroughly before using the cell.
- Batteries have cycle life. Replace failed cell with a new cell that is the same brand immediately after normal life cycle expiration, or if expiration has occurred prematurely. Store battery in a low-humidity and low-temperature environment if the battery won’t be used for an extended period of time.
- Keep it far away from articles or materials with static electric charges while the cell is charged, used or stored.
- Wipe with a dry cloth before using the cell if the terminals of the cell become dirty.
Safety Instructions of Travel
Charger Please read the following information carefully.
-
The maximum ambient temperature of the travel charger shall not exceed 40°C (104 degrees F).
-
The Travel Charger shall be installed according to specification. The current of load and output power shall not exceed the following value:
Input: AC100-240V~ 50/60Hz 0.5A
Output: DC5V 3A/9V 2A/12V ****1.5A -
The Travel Charger shall be used for I.T. equipment only.
-
For indoor use only.
-
Cleaning Unplug this from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners to clean; use only a dry cloth.
-
Water and moisture Do not use this product under moist environment.
-
Self-servicing Attempting to service this product on your own, or opening or removing device covers may result in exposure to dangerous voltage or other hazards.
-
Unplug this apparatus during lighting storms or when unused for lengthy durations.
-
This Travel Charger is not intended to be repaired by service personnel in case of failure or component defect.
FCC Notice and Cautions
This device and its accessories comply with Part 15 of FCC Rules.
Operation is subject to the following conditions:
- This device and its accessories may not cause harmful interference.
- This device and its accessories must accept any interference received, including interference that may cause undesired operation.
Part 15.21 Statement:
Changes or modifications that are not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
Part of Statement 15.105:
This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If you experience interference with reception (e.g.,
television), determine if this equipment is causing the harmful interference
by turning the equipment off and then back on to see if the interference is
affected. If necessary, try correcting the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for further assistance.
TIA Safety Information
The following is the complete TIA Safety Information for wireless handheld
devices:
Exposure to Radio Frequency Signal
Your wireless handheld portable device is a low-power radio transmitter and
receiver. When ON, it receives and sends out Radio Frequency (RF) signals. In
August 1996, the Federal Communications Commissions (FCC) adopted RF exposure
guidelines with safety levels for handheld wireless devices. Those guidelines
are consistent with the safety standards previously set by both U.S. and
international standards `bodies, as follows:
ANSI C95.1 (1992) *
NCRP Report 86 (1986)
ICNIRP (1996)
-
American National Standards Institute; National Council on Radiation Protection and Measurements; International Commission on Non-Ionizing Radiation Protection. Those standards were based on comprehensive and periodic evaluations of the relevant scientific literature. For example, over 120 scientists, engineers, and physicians from universities, government health agencies, and industry reviewed the available body of research to develop the ANSI Standard (C95.1). The design of your device complies with the FCC guidelines (and those standards).
Antenna Care
Use only the supplied or approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the device and may violate FCC regulations.
Tips on Efficient Operation
For your device to operate most efficiently, do not touch the antenna unnecessarily when operating the device. Contact with the antenna affects call quality and may cause the device to operate at a higher power level than otherwise needed, thus reducing battery life.
Pacemakers
The Health Industry Manufacturers Association recommends that a minimum separation of six (6) inches be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with the independent research by and recommendations of Wireless Technology Research.
Persons with pacemakers:- Should ALWAYS keep the device more than six (6) inches from their pacemaker when the device is turned ON;
- Should not carry the device in a breast pocket;
- Should use the ear opposite the pacemaker to minimize the potential for interference;
- Should turn the device OFF immediately if there is any reason to suspect that interference is occurring.
Electronic Devices
Most modern electronic equipment is shielded from RF signals but some
equipment or devices might not be.
Hearing Aids
Some digital wireless devices may interfere with hearing aids. In the event of
such interference, you please consult your service provider, or call customer
service regarding alternatives.
Other Medical Devices
If you use other personal medical devices, consult the device manufacturer to
determine if it is adequately shielded from external RF energy, or your health
care provider may be able to advice about any harmful device interactions.
Vehicles
RF signals may affect improperly installed or inadequately shielded electronic
systems in motor vehicles. Be certain to contact the manufacturer or
representative regarding this as well as manufacturer of any additional
vehicle equipment.
Posted Facilities
Turn your device OFF in any facility where posted notices so require.
For Vehicles Equipped with an Air Bag
DO NOT place objects, including installed or portable wireless equipment, in
the area over the air bag or in the air bag deployment area. If in-vehicle
wireless equipment is improperly installed and the air bag inflates, serious
injury could result since air bags inflate with great force.
Safety Information
Please read and observe the following information for safe and proper use of your device and to prevent damage. Also, keep the user guide in an accessible place after reading it for ease in locating it for future reference. Violation of the instructions may cause minor or serious damage to the product.
- Do not disassemble, open, crush, bend or deform, puncture or shred your equipment.
- Do not modify or remanufacture your equipment. Do not attempt to insert foreign objects into the battery. Do not immerse your equipment in water or other liquids, or expose it to water or other liquids, fire, explosions or other hazards.
- Do not short-circuit the battery or allow metallic conductive objects to contact the battery terminals.
- Avoid dropping the device. If the device is dropped on a hard surface or elsewhere, take it to a service center for inspection if damage is suspected.
Charger and Adapter Safety
- The charger and adapter are intended for indoor use only.
- Insert the battery pack charger vertically into the wall power socket.
- Only use the approved battery charger so as to avoid serious damage to your device.
- When traveling abroad, only use the approved battery pack charger along with the correct device adapter.
Battery Information: Care and Proper Disposal
- Please dispose of your battery properly or take it to your local wireless carrier for recycling.
- The battery doesn’t need to be empty before recharging, and replace the battery when it no longer provides acceptable performance. Note: The battery can be recharged several hundred times and it does not need to be empty in order to recharge.
- Use only manufacturer-approved chargers specific to your device model as they are designed to maximize battery life.
- Do not disassemble or short-circuit the battery.
- Keep the battery’s metal contacts clean.
- Recharge the battery after long periods of non-use to maximize battery life. Note: Battery life will vary due to usage patterns and environmental conditions.
- Use of extended backlighting, Browser, and data connectivity kits affect battery life as well as talk/standby times.
- The self-protection function of the battery cuts the power of the device when its operation is in an abnormal state. In this case, remove the battery from the device, reinstall it, and turn the device on.
Explosion, Shock, and Fire Hazards
- Do not put your device in a place that is subject to excessive dust, and always keep the minimum required distance between the power cord and heat sources.
- Unplug the power cord prior to cleaning your device, and clean the power plug pin when necessary.
- When using the power plug, ensure that it’s firmly connected.
- Placing the device in a pocket or bag without covering the device receptacle (power plug pin), metallic articles (e.g.: coins, paperclips, pens) may short-circuit the device. Always cover the receptacle when not in use.
- Metallic articles that come into contact with the device may short-circuit the + and battery terminals (metal strips) which may result in battery damage, or even an explosion.
General Notice
- Using a damaged battery or placing a battery in your mouth may cause serious injury.
- Do not use the device if the antenna is damaged as it may cause a slight contact burn. Please communicate with the Authorized Service Center to replace the damaged antenna.
- Do not immerse your device in water. If this happens, immediately turn the device OFF and remove the battery. If the device does not work, take it to the Authorized Service Center.
- Do not paint your device.
Consumer Information on SAR
This Model Device Meets the Government’s Requirements for Exposure to Radio
Waves. Your wireless device is a radio transmitter and receiver. It is
designed and manufactured not to exceed the emission limits for exposure to
radiofrequency (RF) energy set by the Federal Communications Commission (FCC)
of the U.S. Government. These FCC exposure limits are derived from the
recommendations of two expert organizations, the National Council on Radiation
Protection and Measurement (NCRP) and the Institute of Electrical and
Electronics Engineers (IEEE). In both cases, the recommendations were
developed by scientific and engineering experts drawn from industry,
government, and academia after extensive reviews of the scientific literature
related to the biological effects of RF energy. The exposure limit for
wireless mobile devices employs a unit of measurement known as the Specific
Absorption Rate, or SAR. The SAR is a measure of the rate of absorption of RF
energy by the human body expressed in units of watts per kilogram (W/kg). The
FCC requires wireless devices to comply with a safety limit of 1.6 watts per
kilogram (1.6 W/kg). The FCC exposure limit incorporates a substantial margin
of safety to give additional protection to the public and to account for any
variations in measurements. Tests for SAR are conducted using standard
operating positions specified by the FCC with the device transmitting at its
highest certified power level in all tested frequency bands. Although SAR is
determined at the highest certified power level, the actual SAR level of the
device while operating can be well below the maximum value. Because the device
is designed to operate at multiple power levels to use only the power required
to reach the network, generally, the closer you are to a wireless base station
antenna, the lower the power output. Before a device model is available for
sale to the public, it must be tested and certified to the FCC that it does
not exceed the limit established by the government adopted requirement for
safe exposure. The tests are performed in positions and locations (e.g., at
the ear and worn on the body) as required by the FCC for each model. This
device was tested for typical body-worn operations with the back of the device
kept 0.39 inches (1.0 cm) between the user’s body and the back of the device.
To comply with FCC RF exposure requirements, a minimum separation distance of
0.39 inches (1.0 cm) must be maintained between the user’s body and the back
of the device. Third-party belt clips, holsters, and similar accessories
containing metallic components should not be used.
Body-worn accessories that cannot maintain 0.39 inches (1.0 cm) separation
distance between the user’s body and the back of the device, and have not been
tested for typical body-worn operations may not comply with FCC RF exposure
limits and should be avoided.
The FCC has granted an Equipment Authorization for this model device with all
reported SAR levels evaluated as in compliance with the FCC RF emission
guidelines.
The highest SAR value for this model device when worn on the body is 1.19
W/kg. While there may be differences between SAR levels of various devices and
at various positions, they all meet the government requirement for safe
exposure.
SAR information on this model device is on file with the FCC and can be found
under the Display Grant section of http://www.fcc.gov/oet/ea/fccid/ after
searching on FCC ID: R38YLCP337AS.
To find information that pertains to a particular model device, this site uses
the device FCC ID number which is usually printed somewhere on the case of the
device. Sometimes it may be necessary to remove the battery pack to find the
number. Once you have the FCC ID number for your device, follow the
instructions on the website and it should provide values for typical or
maximum SAR for that device.
Additional information on Specific Absorption Rates (SAR) can be found on the
Cellular Telecommunications Industry Association (CTIA) website at
http://www.ctia.org/ In the United States and Canada, the SAR limit for
mobile devices used by the public is 1.6 watts/kg (W/kg) averaged over one
gram of tissue. The standard incorporates a substantial margin of safety to
give additional protection for the public and to account for any variations in
measurements.
Standard Limited Warranty
(This standard Limited Warranty supersedes and replaces for all purposes the Standard Limited Warranty that appears in the enclosed documentation, if any) COOLPAD TECHNOLOGIES, INC.(“COOLPAD”) warrants that COOLPAD’s devices and accessories enclosed herein (“Products”) are free from defects in material and workmanship under normal use and service for the period commencing upon the date of purchase by the first consumer purchaser and continuing for the following specified period of time after that date:
Device | 12 months |
---|---|
Battery and Charger | 6 months |
Other Accessories (If included in the box set) | 3 months |
This Limited Warranty is conditioned upon proper use of the Products. This
Limited Warranty does not cover: (a) defects or damage resulting from
accident, misuse, abnormal use, abnormal conditions, improper storage,
exposure to liquid, moisture, dampness, sand or dirt, neglect, or unusual
physical, electrical or electromechanical stress; (b) scratches, dents and
cosmetic damage, unless caused by COOLPAD; (c) ordinary wear and tear; (d)
defects or damage resulting from the use of Product in conjunction or
connection with accessories, products, or ancillary/peripheral equipment not
furnished or approved by COOLPAD; (e) defects or damage resulting from
improper testing, operation, maintenance, installation, service, or adjustment
not furnished or approved by COOLPAD; (f) defects or damage resulting from
external causes such as collision with an object, fire, flooding, dirt,
windstorm, lightning, earthquake, exposure to weather conditions, theft, blown
fuse, or improper use of any electrical source; or (g) Product used or
purchased outside the United States. This Limited Warranty covers batteries
only if battery capacity falls below 80% of rated capacity or the battery
leaks, and this Limited Warranty does not cover any battery if: (i) the
battery has been charged by a battery charger not specified or approved by
COOLPAD for charging the battery;(ii) any of the seals on the battery are
broken or show evidence of tampering; or (iii) the battery has been used in
equipment other than the COOLPAD device for which it is specified.
During the applicable warranty period, provided the Product subject to the
warranty claim is returned in accordance with the terms of this Limited
Warranty, COOLPAD will repair or replace such Product, at COOLPAD’S sole
option, without charge. COOLPAD may, at COOLPAD’s sole option, use rebuilt,
reconditioned, or new parts or components when repairing any Product, or may
replace the Product with a rebuilt, reconditioned or new Product. All other
repaired/replaced Products will be warranted for a period equal to the
remainder of the original Limited Warranty on the original Product or for
ninety (90) days, whichever is longer. All replaced Products, parts,
components, and equipment shall become the property of COOLPAD. Except to any
extent expressly allowed by applicable law, transfer or assignment of this
Limited Warranty is prohibited.
To obtain service under this Limited Warranty, you must return the Product to
an authorized device service facility in an adequate container for shipping,
accompanied by the sales receipt or comparable proof of sale showing the
original date of purchase, the serial number of the Product and the seller’s
name and address. Replacement parts and/or services are available for three
years after the end of production of the product. To obtain assistance on
where to deliver the Product, please call COOLPAD Customer Care at
1-877-606-5753. If COOLPAD determines
that any Product is not covered by this Limited Warranty, you must pay all
parts, shipping, and labor charges for the repair or return of such Product.
You should keep a separate backup copy of any contents of the Product before
delivering the Product to COOLPAD for warranty service, as some or all of the
contents may be deleted or reformatted during the course of warranty service.
THIS LIMITED WARRANTY SETS OUT THE FULL EXTENT OF COOLPAD’S RESPONSIBILITIES,
AND THE EXCLUSIVE REMEDY REGARDING THE PRODUCTS. ALL DISPUTES WITH COOLPAD
ARISING IN ANY WAY FROM THIS LIMITED WARRANTY OR THE SALE, CONDITION OR
PERFORMANCE OF THE PRODUCTS SHALL BE RESOLVED EXCLUSIVELY BY ANY COURT WITH
COMPETENT JURISDICTION. Any such dispute shall not be combined or consolidated
with a dispute involving any other person’s or entity’s Product or claim, and
specifically, without limitation of the foregoing, shall not under any
circumstances proceed as part of a class action. The laws of the State of
California, without reference to its choice of laws principles, shall govern
the interpretation of the Limited Warranty and all disputes arising out of the
products or services.
This settlement of disputes also applies to claims against COOLPAD’S
employees, contractors, agents, and/or other representatives, as well as any
of all of its affiliated entities, regardless of place of incorporation, if
any such claim arises from the Product’s sale, condition or performance.
Notwithstanding the foregoing, neither this warranty nor provision of any
Product shall, in and of itself, provide for in persona jurisdiction over any
of COOLPAD’s employees, contractors, agents, and/or other representatives, or
over its affiliated entities.
Severability
If any portion of this Limited Warranty is held to be illegal or
unenforceable, such partial illegality or unenforceability shall not affect
the enforceability of the remainder of the
Limited Warranty.
Coolpad Technologies, Inc.
Email: hello@coolpad.com
Customer Service: 1-877-606-5753
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>