Hisense MWH505S WiFi/Bluetooth Module User Manual
- June 6, 2024
- Hisense
Table of Contents
MWH505S WiFi/Bluetooth Module
User Manual
The user manual of TV’s WIFIBluetooth module
MODEL: MWH505S
The product description The user can achieve TV connection WIFI net and
Bluetooth, through this module This equipment may be operated in all European
countries.
Basic parameters
Feature Description | Feature Description |
---|---|
Model | SIWHSO5S |
Product Name | BT/Wi-Fi Module |
Major Chipset | MT7663BU |
WLAN Standard | IEEE 802.11a/b/g/n/ac |
BT Standard | BT2.1/3.0/4.0/5.1 |
WLAN Frequency Range | 2.4GHz”2.4835GHz,5.15″5.85GHz |
BT Frequency Range | 2402MHz”2480MHz |
Spread Spectrum | IEEE 802.11b: DSSS (Direct Sequence Spread Spectrum) |
IEEE802.11a/g/n/ac: OFDM (Orthogonal Frequency Division Multiplexing)
Modulation Method| DSSS/BBPSK/DQPSK/16-QAM/ 64-QAM/256QAM
Data Transfer Rate| 1,2,5.5,6,11,12,18,22,24,30,36,48,54,60, 90,120 and
maximum of 867Mbps
Antenna Reference| WIFI1/BT Internal Printed ANT,WiFiO external ANT
Interface| USB2.0
Supply Voltage| 3.3V±0.2V
Dimension| 45 (mm) 30 (mm) 2.85 (mm)
Operating Temperature| -10° C to 70° C
Storage Temperature| -40° C to 85° C
RF output power
| Band| Limited power
---|---|---
BT| 2402MHZ-2480MHZ| 0-20
WlAN| 2412MHZ-2472MHZ| <20
5150MHZ-5850MHZ
The display method of Model approved code
In the factory, the model approve code is pasted on the back shell in a label.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC ID: SARMWH505S
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of FCC RF Rules.
This equipment should be installed and operated with a minimum distance of 20
in (50cm)between the radiator and your body. This transmitter must not be co-
located or operated in conjunction with any other antenna or transmitter
CAUTION:
To comply with the limits of the Class B digital device pursuant to Part 15 of
the FCC Rules, this device is compliant with Class B limits. All peripherals
must be shielded and grounded. Operation with non-certified peripherals or
non-shielded cables may result in interference to radio or reception
MODIFICATION
To assure continued compliance, Any changes or modifications not expressly
approved by the grantee of this device could void the user’s authority to
operate the device.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 50 cm(8 in )between the radiator and your body NOTE To
satisfy FCC exterior labeling requirements, the following text must be placed
on the exterior of the end product Contains Transmitter Module FCC ID:
SARMW505S To satisfy IESD exterior labeling requirements, the following text
must be placed on the exterior of the end product ” Contains Transmitter
Module IC: 27123-MW505S
This symbol on the product or on its packaging indicates that this product
must not be disposed of with your household waste. Instead, it is your
responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and
electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources and
ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste
equipment for recycling, please contact your local city office, your household
waste disposal service or the shop where you purchased the product. The device
is restricted to indoor use only when operating in the 5150 to 5350 MHz
frequency range.
| BG| CZ| DK| DE| EE| IE| EL| ES| FR| HR
---|---|---|---|---|---|---|---|---|---|---
CY| LV| LT| LU| HU| MT| NL| AT| PL| PT
SI| SK| Fl| SE| UK| NO| IS| LI| CH| TR
Manufacturer: QingdaoHisense Communication Co., Ltd.
Address: 218 Qianwangang Road, Qingdao Economic & Technological Development
Zone, Qingdao, China
Importers:
Hisense France SAS
Address: 9 Rue des 3 Soeurs, 93420 Villepinte, France
Hisense Iberia, S.L.U
Address: Ronda Auguste y Louis Lumiere. 23 Nave 12. Edificio Lumiere – Parque
Tecnológico 46980 Paterna (Valencia) – Spain
Hisense Italia S.r.l
Address: Via Montefeltro, 6/A, 20156
MILANO Hisense South Africa
Address: The Estuaries, Building 17 Oxbow Crescent,
Century City, Cape Town, SouthAfrica
IC Statement
i , the device for operation in the band 51505250 MHz is only for indoor use
to reduce the potential for harmful interference to co-channel mobile
satellite systems; Footnote4
ii for devices with detachable antenna(s), the maximum antenna gain permitted
for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that
the equipment still complies with the e.i.r.p. limit;
iii for devices with detachable antenna(s), the maximum antenna gain permitted
for devices in the band 5725-5850 MHz shall be such that the equipment still
complies with the e.i.r.p. limits as appropriate; and iv where applicable,
antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to
remain compliant with the e.i.r.p. elevation mask requirement set forth in
section 6.2.2.3 shall be clearly indicated. This device complies with Industry
Canada’s license-exempt RSS. Operation is subject to the following two
conditions: “Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the
device.
EU DECLARATION OF CONFORMITY
It is hereby declared the following designated product:
Product Type: | BT/Wi-Fi Module | Product colour image |
---|---|---|
Model No: | MWH505S | **** |
Product Description: | BT/Wi-Fi Module | |
Software version: | — | |
Hardware version: | MWH505S V1.00 |
Complies with the essential protection requirements of Directives on Radio Equipment Directive 2014/53/EU. The assessments were based on the following regulations and standards:
Requirement | Standard | Report No. | Assessment Body |
---|---|---|---|
Health and safety | IEC 62368-1:2014 and/or |
EN 62368-1:2014+ A11:2017EN 62311:2020
EN 50383:2010
EN 50385:2017
1999/519/EC| SRTC2022-9003(R)-0008
SRTC2022-9004(R)-22012608(I)| PHOENIX Test Lab
(Notified body 0700) certificate:
EMC| ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-3 V2.1.1 ETSI EN 301 489-17 V3.2.4| BWTR-2211-CEEMC
Radio
Spectrum| ETSI EN 300 328 V2.2.2 (2019-07)
ETSI EN 301893 V2.1.1 (2017-05)
ETSI EN 300 440 V2.2.1 (2018-07)| SRTC2022-9004(R)-22012608(D)
SRTC2022-9004(R)-22012608(E)
SRTC2022-9004(R)-22012608(F)
SRTC2022-9004(R)-22012608(G)
SRTC2022-9004(R)-22012608(P)
This declaration is the responsibility of the manufacturer:
Qingdao Hisense Communication Co., Ltd.
No.218, Qianwangang Road, Economic and Technological Development Zone,
Qingdao, Shandong Province,China
The authorized person signing for the company:
The authorized person signing for the company:
Li Hao
PM(Title) of QingdaoHisense Communication Co., Ltd.
Name in block letters & position in the company
Qingdao, February 24, 2022
Place & date
Legally valid signature
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>