EVEBILT HDSP25W Submersible Sump Pump User Guide

EVEBILT HDSP25W Submersible Sump Pump

Safety Information

• Do not splice the electrical power cord.
• Do not allow the electrical cord to become submerged.
• Do not use extension cords. They are a fire hazard and can reduce voltage sufficiently to prevent pumping and/or damage the motor.
• Do not handle or service the pump while it is connected to a power supply.
• DO NOT remove the grounding prong from the plug or modify the plug to protect against electrical shock. The power cord is a three-wire conductor and includes a 3-prong grounded plug. Plug the pump into a 3-wire, grounded, grounding type receptacle. Connect the pump according to electrical codes that apply.

DANGER: Do not pump flammable or explosive liquids such as oil, gasoline, kerosene, ethanol, etc. Do not use in the presence of flammable or explosive vapors. Using this pump with or near flammable liquids can cause an explosion or fire, resulting in property damage, serious personal injury, and/or death.

DANGER: Al.WAYS disconnect the power to the pump before servicing.

DANGER: Do not touch the motor housing during operation. The motor is designed to operate at high temperatures. Do not disassemble the motor housing.

DANGER: Do not handle the pump or pump motor with wet hands or when standing on a wet or damp surface, or in water before disconnecting the power.

WARNING: Release all pressure and drain all water from the system before servicing any component.

WARNING: Secure the discharge line before starting the pump. An unsecured discharge line will whip, possibly causing personal injury, and/or property damage.

WARNING: Extension cords may not deliver sufficient voltage to the pump motor. Extension cords present a life threatening safety hazard if the insulation becomes damaged or the connection ends fall into water. The use of an extension cord to power this pump is not permitted.

WARNING: Wear safety goggles at all times when working with pumps.

WARNING: This unit is designed only for use on 115 volts (single phase), 60 Hz, and is equipped with an approved 3-conductor cord and 3-prong grounded plug. Do not remove the ground pin under any circumstances. The 3-prong plug must be directly inserted into a properly installed and grounded 3-prong, grounding-type receptacle. Do not use this pump with a 2-prong wall outlet Replace the 2-prong outlet with a properly grounded 3-prong receptacle (a GFCI outlet) installed in accordance with the National Electrical Code and local codes and ordinances. All wiring should be performed by a qualified electrician.

WARNING: Protect the electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid kinking the cord. Do not use damaged or worn cords.

WARNING: Failure to comply with the instruction and designed operation of this unit may void the warranty. ATTEMPTING TO USE A DAMAGED PUMP can result in property damage, serious personal injury, and/or death.

WARNING: Ensure that the electrical circuit to the pump is protected by a 15 Amp fuse or circuit breaker.

CAUTION: Do not lift the pump by the power cord.

CAUTION: Know the pump and its applications, limitations, and potential hazards.

CAUTION: Secure the pump to a solid base. This will aid in keeping the pump in a vertical orientation. This is critical in keeping the pump operating at maximum efficiency. It will also help prevent the pump from clogging resulting in premature failure.

CAUTION: Periodically inspect the pump and system components to ensure the pump suction screen is free of mud, sand, and debris. Disconnect the pump from the power supply before inspecting.

CAUTION: Follow all local electrical and safety codes, along with the National Electrical Code (NEC). In addition, all Occupational Safety and Health Administration (OSHA) guidelines must be followed.

IMPORTANT: Ensure the electrical power source is adequate for the requirements of the pump.

IMPORTANT: This pump is made of high-strength, corrosion-resistant materials. It will provide trouble-free service for a long time when properly installed, maintained, and used. However, inadequate electrical power to the pump, dirt, or debris may cause the pump to fail. Please carefully read the manual and follow the instructions regarding common pump problems and remedies.

IMPORTANT: The motor of this pump has a thermal protector that will trip if the motor becomes too hot The protector will reset itself once the motor cools down and an acceptable temperature has been reached. The pump may start unexpectedly if it is plugged in.

Warranty

The manufacturer warrants the products to be free from defects in materials and workmanship for a period of one year from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If within one years this product is found upon examination by the manufacturer to be defective in materials or workmanship, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect or mishandling. Your original receipt of purchase is required to determine warranty eligibility. The purchaser must pay all labor and shipping charges necessary to replace the product covered by this warranty. This Limited Warranty does not cover products which have been damaged as a result of an accident, misuse, abuse, negligence, alteration, improper installation or maintenance, or failure to operate in accordance with the instructions supplied with the products, or operational failures caused by corrosion, rust, or other foreign materials in the system. Requests for service under this warranty shall be made by returning the defective product to the manufacturer as soon as possible after the discovery of any alleged defect. The manufacturer will subsequently take corrective action as promptly as reasonably possible. The manufacturer does not warrant and especially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. This is the exclusive remedy and any liability for any and all indirect or consequential damages or expenses whatsoever is excluded. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Contact the Customer Service Team at 1-844-883-1872 or visit www.HomeDepot.com.

Pre-Installation

PLANNING INSTALLATION
This submersible sump pump is designed for home sump applications. Use this pump only for pumping water. This unit is not designed as a waterfall or fountain pump, or for applications involving salt water or brine. Use with waterfalls, fountains, saltwater or brine will void the warranty. Do not use where water recirculates. This pump is not designed for use as a swimming pool drainer.
INSTALLATION REQUIREMENTS

NOTICE: Install the pump on a hard, level surface (cement, asphalt, etc.). Never place the pump directly on earth, clay, or gravel surfaces.

• Use a rigid plastic pipe for the discharge. Do not use ordinary pipe joint compound. Pipe joint compound can attack plastics.

CAUTION: Risk of flooding. Can cause personal injury and/or property damage. If a flexible discharge hose is used, make sure the pump is secured in the sump to prevent movement. Failure to secure the pump may allow pump movement, switch interference and prevent the pump from starting or stopping.

• To reduce motor noise and vibrations, a short length of rubber hose (1-7/8 in. (47.6 mm) I.D., e.g. radiator hose) can be connected into the discharge line near the pump using suitable clamps.
• If the check valve is not equipped with an air bleed hole to prevent air locking the pump, drill a 1/8 in. (3.2 mm) hole in the discharge pipe just above where the discharge pipe screws into the pump discharge. Be sure the hole is below the waterline and the check valve to prevent air locks.
• If the pump discharge line is exposed to outside subfreezing atmosphere, a portion of line exposed must be installed so any water remaining in the pipe will drain to the outfall by gravity. Failure to do this can cause water trapped in the discharge to freeze which could result in damage to the pump.
• The shaft seal depends on water for lubrication. Do not operate the pump unless it is submerged in water as the seal may be damaged if allowed to run dry.
  Do not change the preset tether switch length.

ELECTRICAL REQUIREMENTS

• For automatic operation, plug the pump into a GFCI wall outlet. Connect the pump to an individual branch circuit with no other outlets or equipment in the circuit.
• Size fuses or circuit breakers according to this chart:

PERFORMANCE CHART

SPECIFICATIONS

tethered switch Min. 14 in. (356 mm) diameter, 24 in. (61O mm) depth for vertical switch
Switch on/off| 1006 013 623|
 | 1006 013 667| ON:14.68 +/- 0.40in. , OFF: 7.59 +/- 0.40 in.
 | 1006 013 668|
 | 1006 013 666|
 | 1006 013 664

1006 013 663

| ON: 7.06 +/- 0.40 in. , OFF: 5.26 +/-0.40 in.

TOOLS REQUIRED

MATERIALS REQUIRED {NOT INCLUDED)

NOTE: Hardware not shown to actual size.

PACKAGE CONTENTS

Part      Description

A         Pump
DD        Adapter (1-1/2 in. MNPT X 1-1/4 in. FNPT)

Installation

1. Preparing a pump basin
   • The sump pump must be installed in a sump basin with a minimum diameter of 14 in. (356 mm)for vertical switch models and 18 in. (457 mm) for tethered float switch models.
   • The sump basin must have a minimum depth of 24 in. ( 610 mm) for vertical switch models and tethered float switch models.
   • The sump basin can be constructed of tile, concrete, steel, or plastic. Check local codes for approved materials and for proper installation.
2. Placing the pump in a basin
   • Place the pump on a hard surface inside the sump basin. Do not install the pump on clay, earth, or sand surfaces.
   • Clear the sump basin of debris which could clog the pump. Keep the inlet screen clear.
3. Installing the discharge plumbing
   • Attach a pipe adapter (DD) to the discharge pipe (AA). Wrap the threads with PTFE pipe thread sealant tape.
   • Screw the discharge pipe (AA) onto the pump (A) hand-tight, plus 1-1/2 turns.
   • Install an in-line check valve (BB) or an in-pump check valve.

Operation

1. Connecting power

   • Plug the power cord into a 115 V GFCI power outlet.
     WARNING: Do not handle this pump or plug in or unplug this pump with wet hands or while standing in water, unless you are certain all power has been turned off to the pump. Remember, the pump should be connected only to a properly grounded, GFCI outlet.

2. Operating the pump

   • After connecting power to the pump, test the pump by filling the sump basin with water and observing pump operation through one complete cycle.
   • The motor is equipped with an automatically-resetting thermal overload protector. If the motor gets too hot, the overload protector will shut off the pump before it is damaged. When the motor has cooled sufficiently, the overload protector will reset, and the motor will restart.
   • The pump will not remove all water. If operating a pump manually, and suddenly no water comes out of the discharge hose, shut off the unit immediately. The water level is probably very low and the unit has broken prime.
     NOTICE: If the overload protector stops the pump repeatedly, disconnect the power from the pump and check to find the problem. Low voltage, a long extension cord, clogged impeller, screen blocked by debris, or water that is too hot can cause motor overheating.

Care and Cleaning

WARNING: Before removing the pump from the basin for service, always disconnect electrical power to the pump and control switch. Do not lift the pump by the power cord.

• Unscrew the bolts (1) and remove the volute (2).
• Remove debris from around the impeller(3). ( Do not remove impeller.)
• Reassemble the pump.

Troubleshooting

□   Reset the circuit breaker

□   Make sure the pump is plugged in

□   Clean the plug prongs

The impeller is blocked.| Remove the debris around the impeller.
The float switch failed.| Replace the float switch.
The motor failed.| Replace the pump.
The pump operates, but pumps little or no water.| The screen is blocked.| Clean the screen.
Debris is caught in the impeller or discharge.| Remove the debris.
The impeller is broken.| Replace the impeller.
The pump starts and stops too often.| There is a backflow of water from the piping or the check valve is leaking.| Install or replace the check valve.
The float switch is stuck.| Clean float switch.
The float switch failed.| Replace the float switch.
The pump will not shut off.| The float switch is tangled.| Reposition the pump and make sure the switch moves freely.
The float switch failed.| Replace the float switch.

Questions, problems, missing parts? Before returning to the store,
call Everbilt Customer Service
B a.m. – 7 p.m., EST, Monday-Friday, 9 a.m. – 6 p.m., EST, Saturday
1-844-883-1872
HOMEDEPOT.COM
Retain this manual for Mure use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>