LOCOCO U60 Series UHF Wirelss Recording Microphone Instruction Manual

Wireless Recording Microphoneiln
U60 Series
Instruction for use

• Mini stylish exterior design
• Long range wireless transmission
• Recording real-time monitoring
• High definition call& recording
  

Please rood this manual carefully before using the product *

Thank you for choosing to use our wireless microphone products!
This device is a multi-purpose UHF wireless transmitter (low power consumption, long-distance). It can be used with UHF receiver for wireless recording of mobile phones, cameras and computers.

• Mini stylish exterior design
• Long-distance wireless transmission, strong anti-interference
• High-sensitivity microphone core and professional wireless solution
• Clear wireless recording. with real-time monitoring function
• AA* 2 batteries, also con be connected to the external DC5V power supply
• High-brightness led display. more intuitive working state

PRECAUTIONS AND WARM TIPS

1. The leveller mic is clamped in the color mouth, about 5-10cm away from the mouth is more appropriate. and then the volume is adjusted to the appropriate size (11 levels of volume con be adjusted)
2. If you need to replace the battery, must use the same specification (the some typo or equivalent type battery can be replaced otherwise of may load to the machine can not work normally or damage. If the battery is not replaced property there will be an explosion risk! (Please refer to the technical parameters of the 6th product for battery specifications)
3. When using external power adopters, Please select 3C certification and meet the standard requirements the adopter (DC 5v ****500mA).
4. Under normal circumstances. the products have been paired when leaving the factory. and can be used normally when unpacked without frequency alignment, If you need to adjust the frequency please follow the sixth: product use method to operate.

PRODUCT FUNCTION INTRODUCTION

Figure 1: Transmitter

1. The transmitter antenna
2. Owe! &splay
3. Micrcohoce input 3.5mm pat
4. Volume +/ Frequency + (long press 10 seconds to pat)
5. Volume -/ frequency –
6. AUX audio input
7. Power switch (long press On/Off, short press to switch model)
8. Bock clip
9. External power supply interface (DC 5V ****)
10. Battery holder (AA*2)

Figure 2: Receiver

1. The Receiver antenna
2. Indicator light (Blue light)
3. Audio output 3.5mm Port
4. 3.5MM headset monitoring port
5. Power switch (long press 2s On/Off)
6. Sack dip
7. External power supply interface (DC 5V ****)
8. Battery holder( AA*2)

DIAGRAM OF TRANSMITTER CONNECTION

1. Insert the delivered lavalier Mic into the transmitter 3.SmmMIC input interface. The microphone interface adopts a nut structure to make the connection more sold and less likely to have bad contact. so that you con have a better user experience.
2. Insert the delivered audio cable end into the 3.5mm LINE IN Interface of the transmitter, and insert the other end into the output interlace of the audio device.
   All audio devices can be transformed into wireless from matters in seconds.

DIAGRAM OF THE RECEIVER CONNECTED TO CAMERA/DESKTOP COMPUTER RECORDING

Fest. insert the receiver back clip into the hot shoe interface on the comers and then insert the 3.5mmplug end of the delivered recording cable into the CAMERA MIC input interface to achieve camera recording.

Computer recording can be realized by inserting the 3.5mm plug end of the recording cable into the MIC input interface of the desktop computer (generally pink).

RECEIVER CONNECTED TO MOBILE PHONE FOR RECORDING – SCHEMATIC

Fix the Lovelier MIC to the transmitter (MIC IN) interface and tighten the nut.
Then fix the Cell phone recording cable nut end to the receiver (Line OUT] interface, and tighten the nut.
Then fix the phone recording wire not end to the receiver (line OUT) interface, and tighten the nut.
The earphone can be plugged into the receiver mouthpiece to monitor the effect of the recording in real-time.

iPhone 7/8/X (Without 3.5mm Headphone jack)

Note: ABOUT THE LIMITATIONS OF VIDEO TAKING ON ANDROID PHONES

On Android phones mode before 2019, The belt-in Android camera app doesn’t support an external microphone. Third potty video APP software must be used to shoot. Such as Open Camera, Xicsoying, Douyin. Kvaishou and other software can solve this problem. There are no such restrictions lot live streaming and recording. Most Android phones released after 2019 (Android 10.0 or higher) don’t have these restrictions. There are no such restrictions on iPhones.

HOW TO USE THE PRODUCT

1. The connection between transmitter and receiver
   Long press the transmitter dextral power button for 2s. Then long-press the top button “VOLUME+” About 10 seconds.
   When a bright spot on the display screen flashes from left to right quickly, Release it and press the receiver power button immediately to enter the wireless paling. After a few seconds. The display of the transmitter is normal and the receiver’s blue light is always on. Indicating that the transmitter and the receiver are matched successfully, You can use it.

2. Frequency or Volume adjustment
   When the transmitter is turned on. The display “U08” indicates that the defoult volume of the system is level 8. At this time. Press the top button “-VOLUME-to reduce the volLene. Press the top button” VOLUME+ ” to increase the volume, press one button to reduce or increase the volume by 1 level. Which con be adjusted from 0-11 levels in total.
   Short press the power button to switch to the frequency display 386.5″. indicating that the default frequency of the system is 586.5MHz. At this time press the top button
   “-VOLUME to reduce the frequency, Press the right button “VOLUME+” to increase the frequency. Press once to reduce or increase the frequency by 1MHz. Frequency range: 572.5-586.5MHz. A total of 15 frequency points are adjustable.

3. Multiple devices used at the some time
   When multiple devices are used of the same time, You must follow the above steps (1. the connection method between the transmitter and the connector) to reconnect once, And then adjust the frequency according to Step2 If 10 devices are used at the same time. the frequency must be adjusted in sequence. And theta con is no repetition between the 10 frequency points.
   This product can support 15 units at the same time no crosstalk frequency, no interference!

4. Battery power display:
   The battery symbol on the display is . Display 3 grid means electric quantity 100%Display 2 grid means 75% electric quantity. Display 1 grid means electricity50%: when only is displayed and flashing. Indicating that the power has been lower than 25%. Please turn off and charge in time.

5. External power supply::
   When dry batteries are not installed a the battery is dead, the product con be supplied with a DC 5V Output charger or a mane power supply to prevent interruption of use.

6. Factory reset settings
   Press and hold to the” VOLUE+ ” button in the shutdown State. And then turn on the power switch. At this tittle. the display screen displays ‘LW” into the circular flash mode and releases it. And then immediately turn on the receiver power switch to enter the reset mode. Alter a few seconds. The display screen displays normal and the recovered blue light is always on. Real factory setting successfully.

PRODUCT TECHNICAL PARAMETERS

ACCESSORIES LIST

Warranty Card

Product ModelUser Name____
Dote of Purchase Contact Way_
Contact Address___

1. The products provided by the company. non-humondomoge, the implementation of a one-veer warranty, after-sale within a month due to product quality problems unconditional and timely replacement.
2. Alter the warranty period, the company wit follow up from time to time free of charge to assist in daily maintenance responsible for lifelong maintenance depending on the cost of materials
3. For quality or maintenance issues. please contact the local distributors.
4. The following circumstances do not enjoy warranty services:
   a. artificial damage caned by failure to use maintain and keep the product is not in accordance aim the instructions for use
   b. damage caused by tee cementing of the machine by technicians not related to the company.
   C. damage caused by force majeure.
   

Note: Due to the continuous optimization of products, parameters may change without notice, the actual packaging of the product shod prevail, the right of interpretation belongs to the company!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>