Bestway 65115 Hydro-Force Inflatable Cove Champion Owner’s Manual
- June 6, 2024
- Bestway
Table of Contents
Bestway 65115 Hydro-Force Inflatable Cove Champion
Whats in the box
WARNING: To avoid damage to the boat and injury to passengers, please don’t exceed the data given on the builder’s plate.
Technical Specifications
WARNING
Follow all the Safety and Operating Instructions. If you don’t follow this
instruction, it may cause overturn, explode the boat and causes to drowning.
-
Do not exceed the maximum recommended number of persons. Regardless of the number of persons on board, the total weight of persons and equipment must never exceed the maximum recommended load. Always use the seats / seating spaces provided.
-
When loading the craft, never exceed the maximum recommended load: Always load the craft carefully and distribute loads appropriately to maintain design trim (approximately level). Avoid placing heavy weights high up.
NOTE: The maximum recommended load includes the weight of all persons onboard, all provisions and personal effects, any equipment not included in the light craft mass, cargo (if any) and all consumable liquids (water, fuel, etc.). -
When using the boat, life-saving devices such as life jackets and buoys should be pre-inspected and used at all times.
-
Before every use, carefully inspect all boat components including air chambers, grab ropes, oars, and air valves, to ensure everything is in good condition and tightly secured. Please stop to repair if you find any damage.
-
Buckets, water scoops and air pumps should always be available in case of air leakage or if the boat takes on water.
-
Passenger numbers and load weights shall by no means exceed specified capacities. Refer to the Technical Specifications section of this manual to determine passenger numbers and load weights for your boat. Overweight will cause overturn and drowning.
-
Inflate according the numbered air chamber and rated pressure on the boat, or it will cause overinflation and boat explosion. Exceeding the data given on the capacity plate may cause the craft to damage, overturn and lead to drowning.
-
Keep the boat balanced. Uneven distribution of persons or load in the boat may cause overturn the boat and drowning.
-
When the boat is in motion, all passengers must remain seated at all times to avoid going overboard.
-
Use the boat in protected shore zones, up to 300 m (984 feet). Be careful with natural factors such as wind, tidewaters and tidal waves. BE AWARE OF OFFSHORE WINDS AND CURRENTS.
-
Be careful when landing on the shore. Sharp and rough objects such as rocks, cement, shells, glass, etc. may puncture the boat.
-
If one chamber is punctured when the boat is in the water, it may be necessary to fully inflate the other air chamber to prevent the boat from sinking.
-
To avoid damage do not drag the boat on rough surfaces.
-
Don’t leave the boat exposed to sun for long periods of time, as high temperatures shall give rise to air expansion, which can cause irreparable damage.
-
Always wear a life jacket!
-
It is the responsibility of the owner/operator to have at least on bucket/bailer on board, secured against accidental loss.
-
Never transport the boat in inflated condition on the car. Be aware of the potential harmful effects of liquids such as battery acid, oil, petrol. The liquids may damage your boat.
-
Be responsible, do not neglect the safety rules, this could jeopardize your life and the lives of others.
-
Follow these instructions to avoid drowning, paralysis or other serious injuries.
-
Know how to operate a boat. Check-in your local area for information and/or training as needed. Inform yourself about local regulations and dangers related to boating and/or other water activities.
ASSEMBLING OF THE BOAT
NEVER USE HIGH-PRESSURE AIR TO INFLATE INFLATABLES, THIS CAN DAMAGE YOUR PRODUCT.
- Spread out the boat on level ground.
- Assemble the removable fin to the bottom of the boat (Fig.1). Make sure the curvature of the fin is pointed towards the back end of the boat.
NOTE:
- Assemble the fin before inflation and also disassemble it after deflation.
- To avoid damage to the removable fin, do not enter shallow water
OVERVIEW
-
Inflate the air chambers with a HAND air pump.
An inflation scale is provided with the product.
Inflate the product until the printed scale is charged up to the same level as that of the supplied scale. (refer the belowing Table and Illustration)
Caution: Under and over-inflation of the boat will result in safety hazards. It is better to check the pressure of the boat each time before using. If you use other pressure gauges, the boat pressure should not be more than the data given on the builder’s plate. -
Never stand on or rest objects on the boat during inflation.
-
Inflate bottom chamber and other accessories such as seat until it is stiff to the touch but NOT hard.
-
Extended exposure to sun can shorten the lifespan of your boat. We suggest not leaving boats in direct sunlight for more than 1 hour after use.
| Item | Product Inflated Size | Printed Scale |
|---|---|---|
| Deflated Size | Inflated Size | |
| 65115 | 2.75 m x 81 cm (9′ x 32″) | 5 cm / 10 cm |
Oars Installation
NOTE: All drawings for illustration purpose only. May not reflect actual product.
Storage
-
Keep all accessories for future use.
-
Carefully clean the boat using a mild soap with clean water.
Note: Do not use acetone, acid, and/or alkaline solutions. -
Use a cloth to gently dry all surfaces.
Note: Do not dry the product in direct sunlight. Also, never dry with equipment such as electric blowers. Doing so will cause damage and shorten the boat’s life span. -
Deflate the hull chambers. Deflate all the hull chambers at the same time so the air-pressure drops together. This will prevent damage from occurring to the boat
inner structures. Next deflate the floor and seat. -
Fold the boat from front to back to remove additional air. You can also use a pump to drain any remaining air.
Repair
- If there is a small puncture, repair it according to the instruction on repair patch.
- If the hole is too big to be repaired with the provided patch, purchase a Bestway repair kit or send the boat to a speciality shop to make the repair.
Registration (For US/Canada customers only)
If you need to register your boat, please have the boat Hull Identification Number and model name ready and then visit
bestwaycorp.com/support to obtain your Certificate of Origin, or you can send e-mail to service@bestwaycorp.us for the Certificate of Origin.
The HIN is located on the starboard outboard side of the hull and near the stern.
PLEASE KEEP THIS MANUAL IN A SECURE PLACE, AND HAND IT OVER TO THE NEW OWNER WHEN YOU SELL THE CRAFT.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>